S208TX
Recommended Milling Conditions
General processing
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.11 Copper
Work Material
100
100
65
65
55
65
100
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S208TX-R0.5 1 31,500 564 31,500 564 25,000 412 25,000 412 22,000 296 25,000 412 31,500 564 32,000 700 S208TX-R0.75 1.526,250 578 26,250 578 20,860 418 20,860 418 14,800 302 20,860 418 26,250 578 25,500 715 S208TX-R1 2 21,000 582 21,000 582 16,720 425 16,720 425 11,000 310 16,720 425 21,000 582 19,000 730 S208TX-R1.25 2.515,750 596 15,750 596 12,580 430 12,580 430 8,900 316 12,580 430 15,750 596 12,700 745 S208TX-R1.5 3 10,500 620 10,500 620 8,450 435 8,450 435 7,400 322 8,450 435 10,500 620 12,500 760 S208TX-R2 4 9,250 630 9,250 630 6,350 442 6,350 442 5,550 342 6,350 442 9,250 630 9,500 765 S208TX-R2.5 5 7,950 640 7,950 640 5,095 447 5,095 447 4,460 377 5,095 447 7,950 640 7,650 775 S208TX-R3 6 5,300 670 5,300 670 4,200 465 4,200 465 3,700 390 4,200 465 5,300 670 6,300 800 S208TX-R4 8 3,950 790 3,950 790 3,150 555 3,150 555 2,750 455 3,150 555 3,950 790 4,750 950 S208TX-R5 10 3,150 745 3,150 745 2,500 525 2,500 525 2,200 430 2,500 525 3,150 745 3,800 890 S208TX-R6 12 2,650 700 2,650 700 2,100 490 2,100 490 1,850 430 2,100 490 2,650 700 3,170 840 S208TX-R8 16 1,990 525 1,990 525 1,580 370 1,580 370 1,390 325 1,580 370 1,990 525 2,400 630 S208TX-R10 20 1,590 420 1,590 420 1,260 290 1,260 290 1,110 260 1,260 290 1,590 420 1,900 500
ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D
Depth of Cut （ mm ）
ae:0.2D ae:0.2D ae:0.2D ae:0.2D ae:0.1D ae:0.1D ae:0.2D ae:0.2D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
44
Made with FlippingBook - Online Brochure Maker