S210TX
Recommended Milling Conditions
General processing
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.11 Copper
Work Material
100
100
65
65
55
65
100
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S210TX-R0.5 1 25,200 480 25,200 480 20,000 320 20,000 320 17,600 225 20,000 320 25,200 480 25,600 560 S210TX-R0.75 1.516,640 480 16,640 480 13,600 320 13,600 320 11,840 225 13,600 320 16,640 480 20,400 560 S210TX-R1 2 12,400 480 12,400 480 10,000 320 10,000 320 8,800 230 10,000 320 12,400 480 15,200 560 S210TX-R1.25 2.512,400 480 12,400 480 8,160 320 8,160 320 7,120 230 8,160 320 12,400 480 10,160 560 S210TX-R1.5 3 8,400 500 8,400 500 6,760 325 6,760 325 5,920 230 6,760 325 8,400 500 10,000 608 S210TX-R2 4 6,360 500 6,360 500 5,080 355 5,080 355 4,440 300 5,080 355 6,360 500 7,600 608 S210TX-R2.5 5 6,360 500 6,360 500 4,070 355 4,070 355 3,568 300 4,070 355 6,360 500 6,120 608 S210TX-R3 6 4,240 535 4,240 535 3,360 370 3,360 370 2,960 310 3,360 370 4,240 535 5,040 640 S210TX-R4 8 3,160 630 3,160 630 2,520 445 2,520 445 2,200 360 2,520 445 3,160 630 3,800 760 S210TX-R5 10 2,520 600 2,520 600 2,000 420 2,000 420 1,760 340 2,000 420 2,520 600 3,040 710 S210TX-R6 12 2,120 560 2,120 560 1,680 390 1,680 390 1,480 340 1,680 390 2,120 560 2,530 670 S210TX-R8 16 1,590 420 1,590 420 1,260 295 1,260 295 1,110 260 1,260 295 1,590 420 1,920 500 S210TX-R10 20 1,270 335 1,270 335 1,000 230 1,000 230 888 200 1,000 230 1,270 335 1,520 400
ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D ap:0.1D
Depth of Cut （ mm ）
ae:0.2D ae:0.2D ae:0.2D ae:0.2D ae:0.1D ae:0.1D ae:0.2D ae:0.2D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
46
Made with FlippingBook - Online Brochure Maker