S645TX / S676ATX Recommended Milling Conditions
S645TX / Side Milling (High-speed machining)
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.6 Hardened Steel （ 48~56HRC ）
GR.7 Hardened Steel （ 56~68HRC ）
Work Material
200
150
100
80
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S645TX-1 S645TX-1.5 S645TX-2 S645TX-2.5 S645TX-3 S645TX-4 S645TX-5 S645TX-6 S645TX-8 S645TX-10 S645TX-12 S645TX-16 S645TX-20
1
21,233
1,000 1,100 1,100 1,274 1,274 1,274 1,528 1,800 1,700 1,650 1,650 1,600 1,450
23,900 21,233 21,233 19,100 15,925 11,943
1,050 1,100 1,100 1,150
23,900 21,231 15,900 12,740 10,616
950
25,477 16,980 12,740 10,200
1,020
1.5 21,233
1,000
815 660 570 509 509 509 600 550 500 480 480 475
2
21,233
820 715 637 637 764 900 850 800 785 780 730
2.5 21,233
3 4 5 6 8
21,233 15,925 12,740 10,500
955 955
8493 6370 5096 4,200 3,200 2,500 2,100 1,600 1,300
7,962 6,370 5,300 4,000 3,200 2,600 2,000 1,600
9,555 8,000 5,900 4,700 4,000 3,000 2,400
1,146 1,350 1,350 1,300 1,300 1,200 1,100
8,000 6,300 5,300 4,000 3,200
10 12 16 20
ap:1.5D
ap:1.5D
ap:1.0D
ap:1.0D
Depth of Cut （ mm ）
ae:0.05D
ae:0.05D
ae:0.02D
ae:0.02D
S676ATX / High SpeedSide Milling
GR.5 Hardened Steel （ 38~48HRC ）
GR.6 Hardened Steel （ 48~56HRC ）
GR.7 Hardened Steel （ 56~68HRC ）
Work Material
200
150
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
S676ATX-3 S676ATX-4 S676ATX-5 S676ATX-6 S676ATX-8 S676ATX-10 S676ATX-12 S676ATX-16 S676ATX-20
3 4 5 6 8
21,233 15,925 12,740 10,617
1,620 1,725 1,750 1,200 1,200
15,925 11,944
1,130 1,200 1,200
10,617
424 477 510 530 530 420 420 420 420
7,963 6,370 5,308 3,981 3,185 2,654 1,991 1,593
9,555 7,963 5,972 4,778 3,981 2,986 2,389
700 700 630 630 650 650
7,963 6,370 5,308 3,981 3,185
10 12 16 20
850 850 900 900
ap:1.5D
ap:1.5D
ap:1.5D
Depth of Cut （ mm ）
ae:0.01D
ae:0.01D
ae:0.01D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
56
Made with FlippingBook - Online Brochure Maker