E110HX
Recommended Milling Conditions
Chamfering
GR.4 Hardened Steel （ 30~38HRC ）
GR.8 Stainless Steel
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.9 Cast Iron
GR.10 Aluminium
GR.10 Aluminium
GR.1 Carbon Steel
GR.15 Titanium
Work Material
30 ～ 60
25 ～ 70
15 ～ 40
25 ～ 50
30 ～ 80
15 ～ 30
25 ～ 80
100 ～ 200
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E110HX-1 E110HX-1.5 E110HX-2.0 E110HX-2.5 E110HX-3 E110HX-3.5 E110HX-4 E110HX-4.5 E110HX-5 E110HX-5.5 E110HX-6 E110HX-8 E110HX-10 E110HX-12
1 14,3232,14814,3232,1487,957 47711,14083514,3232,1484,774 28614,3232,14831,8304,700 1.5 9,549 1,430 9,549 1,430 5300 318 7,427 557 9,549 1,430 3,183 190 9,549 1,430 21,220 3,183 2 7,1611,2807,1611,28039782385,5704177,1611,2802,3871437,1611,28015,9152,387 2.5 5,729 1,030 5,729 1,030 3183 238 4,456 400 5,729 1,030 1,909 114 5,729 1,030 12,732 1,900 3 4,7741,0004,7741 , 000 2652 198 3,713 334 4,774 1,000 1,591 100 4,774 1,000 10,610 1,591 3.5 4,547 818 4,547 818 2728 204 3,637 381 4,547 818 1,818 136 4,547 818 9,094 1,364 4 3,9788353,97883523872143,1833343,9788351,5911193,9788359,5491,432 4.5 3,536 742 3,536 742 2122 190 2,828 296 3,536 742 1,414 127 3,536 742 8,848 1,327 5 3,1837633,18376319102002,5463053,1837631,2731143,1837637,6391,145 5.5 3,100 651 3,100 651 1736 182 2,314 277 3,100 651 1,157 121 3,100 651 6,944 1,041 6 2,9176122,91761218561942,3872862,9176121,0611112,9176126,366954 8 2,1886122,18861213921941,7902862,188612 994 1592,1886125,5701,114 10 1,750 612 1,750 612 1114 222 1,432 286 1,750 612 795 159 1,750 612 4,4561,114 12 1,591 668 1,591 668 928 250 1,193 286 1,591 668 663 159 1,591 668 3,7131,114
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
86
Made with FlippingBook - Online Brochure Maker