E126X / E128X
Recommended Milling Conditions
Side Milling
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.11 Copper
Work Material
65
65
55
40
38
40
65
115
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E126X/E128X-3 3 6,750 360 6,750 360 5,550 265 3,975 90
3,600
85
3,975
90
6,750 360 11,850 645
E126X/E128X-4 4 5,000 375 5,000 375 4,125 265 3,200 100 2,775 85 E126X/E128X-5 5 3,975 450 3,975 450 3,375 315 2,625 100 2,400 90 E126X/E128X-6 6 3,375 450 3,375 450 2,775 320 2,250 105 1,988 95
3,200 100 5,000 375 9,000 675 2,625 100 3,975 450 7,050 780 2,250 105 3,375 450 5,850 780 1,820 100 2,900 430 5,000 770
E126X-7
7 2,900 430 2,900 430 2,360 315 1,800 100 1,700 95
E126X/E128X-8 8 2,475 410 2,475 410 1,950 310 1,400 90
1,425
95
1,400
90 95 95 90 90
2,475 410 4,350 760 2,200 400 3,950 760 1,950 390 3,600 760 1,800 390 3,300 760 1,650 390 3,000 760
E126X-9
9 2,200 400 2,200 400 1,775 305 1,270
95
1,270 100 1,250 1,125 100 1,125
E126X/E128X-10 10 1,950 390 1,950 390 1,575 300 1,125 95
E126X-11
11 1,800 390 1,800 390 1,450 305 1,000
90 90
1,000
95 90 90 75 70
1,000
E126X/E128X-12 12 1,650 390 1,650 390 1,350 305
900 900 825 675
900 825 750 600
900 900 825 675
E126X-14
14 1,430 413 1,430 413 1,200 310
105 100
105 1,430 413 2,550 750 100 1,275 400 2,250 720
E126X/E128X-16 16 1,275 400 1,275 400 1,050 310
E126X/E128X-20 20 975
375
975
375
825
275
70
70
975
375 1,800 670
ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D ap:2.5D
（ mm ）
ae:0.1D ae:0.1D ae:0.1D ae:0.1D ae:0.1D ae:0.1D ae:0.1D ae:0.1D
※ Notice: E128X is Long Length series End Mills. Please adjust the parameter according 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
100
Made with FlippingBook - Online Brochure Maker