E158TX / E159TX
Recommended Milling Conditions
Side Milling
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.5 Hardened Steel （ 48~56HRC ）
GR.5 Hardened Steel （ 56~68HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
Work Material
100
100
80
65
62
60
30
62
100
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E158TX-1 E158TX-1.5 E158TX-2 E158TX-2.5 E158TX-3 E158TX-4
1 31,850 509 31,850 509 25,480 407 20,700 331 19,747 315 19,110 305 9,555 152 19,747 315 31,850 509 1.5 21,233 594 21,233 594 16,986 475 13,800 386 13,164 368 12,740 305 6,370 152 13,164 368 21,233 594 2 15,925 637 15,925 637 12,740 560 10,351 455 9,873 395 9,555 344 4,777 152 9,873 395 15,925 637 2.5 12,740 764 12,740 764 10,192 611 8,281 496 7,898 473 7,644 458 3,822 152 7,898 473 12,740 764 3 10,600 950 10,600 950 8,300 750 7,000 560 6,600 510 6,400 480 3,200 180 6,600 510 10,600 950 4 8,000 1,000 8,000 1,000 6,150 800 5,200 560 5,000 600 4,800 510 2,400 185 5,000 600 8,000 1,000
E158TX-5 5 6,350 1,000 6,350 1,000 5,000 840 4,200 580 4,000 610 3,800 530 2,000 190 4,000 610 6,350 1,000 E158TX/E159TX-6 6 5,300 1,200 5,300 1,200 4,200 950 3,500 700 3,300 650 3,200 540 1,600 190 3,300 650 5,300 1,200 E158TX/E159TX-8 8 4,000 1,200 4,000 1,200 3,100 900 2,700 650 2,500 640 2,400 550 1,200 175 2,500 640 4,000 1,200 E158TX/E159TX-10 10 3,200 1,100 3,200 1,100 2,500 850 2,100 600 2,000 585 1,900 520 950 155 2,000 585 3,200 1,100 E158TX/E159TX-12 12 2,650 1,100 2,650 1,100 2,000 850 1,750 560 1,700 530 1,600 470 800 160 1,700 530 2,650 1,100 E158TX/E159TX-16 16 2,000 950 2,000 950 1,600 730 1,300 500 1,250 430 1,200 400 600 160 1,250 430 2,000 950 E158TX/E159TX-20 20 1,600 760 1,600 760 1,300 580 1,100 450 980 380 950 350 480 160 980 380 1,600 760
ap:1.5D ap:1.5D ap:1.5D ap:1.5D ap:1.5D ap:1.0D ap:1.0D ap:1.5D ap:1.5D
（ mm ）
ae:0.2D ae:0.2D ae:0.2D ae:0.1D ae:0.1D ae:0.05D ae:0.05D ae:0.1D ae:0.2D
※ Notice: E159TX is Long Length series End Mills. Please adjust the parameter according
Side Milling (High-speed machining)
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.5 Hardened Steel （ 38~48HRC ）
GR.5 Hardened Steel （ 48~56HRC ）
GR.5 Hardened Steel （ 56~68HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
Work Material
200
200
200
200
150
100
80
150
200
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E158TX-3 E158TX-4 E158TX-5 E158TX-6 E158TX-8 E158TX-10 E158TX-12 E158TX-16 E158TX-20
3 21,233 1,274 21,233 1,274 21,233 1,274 21,233 1,274 15,925 955 10,616 637 8493 509 15,925 955 21,233 1,274 4 15,925 1,274 15,925 1,274 15,925 1,274 15,925 1,274 11,943 955 7,962 637 6370 509 11,943 955 15,925 1,274 5 12,740 1,528 12,740 1,528 12,740 1,528 12,740 1,528 9,555 1,146 6,370 764 5096 509 9,555 1146 12,740 1,528 6 10,500 2,800 10,500 2,800 10,500 2,500 10,500 1,800 8,000 1,350 5,300 900 4,200 600 8,000 1,350 10,500 2,800 8 8,000 2,400 8,000 2,400 8,000 2,300 8,000 1,700 5,900 1,350 4,000 850 3,200 550 5,900 1,350 8,000 2,400 10 6,300 2,350 6,300 2,350 6,300 2,200 6,300 1,650 4,700 1,300 3,200 800 2,500 500 4,700 1,300 6,300 2,350 12 5,300 2,350 5,300 2,350 5,300 2,100 5,300 1,650 4,000 1,300 2,600 785 2,100 480 4,000 1,300 5,300 2,350 16 4,000 1,800 4,000 1,800 4,000 1,800 4,000 1,600 3,000 1,200 2,000 780 1,600 480 3,000 1,200 4,000 1,800 20 3,200 1,500 3,200 1,500 3,200 1,500 3,200 1,450 2,400 1,100 1,600 730 1,300 475 2,400 1,100 3,200 1,500
ap:1.5D ap:1.5D ap:1.5D ap:1.5D ap:1.5D ap:1.0D ap:1.0D ap:1.5D ap:1.5D
（ mm ）
ae:0.05D ae:0.02D ae:0.05D ae:0.05D ae:0.05D ae:0.02D ae:0.02D ae:0.05D ae:0.05D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
104
Made with FlippingBook - Online Brochure Maker