F690TX
Recommended Milling Conditions
Side Milling
GR.1 / GR.2 / G R.3 Carbon Steel / Low-alloyed Steel / Hi-alloyed Steel （ ~24HRC ） （ ~30HRC ）
GR.4 / GR.5 Hardened Steel/ Hardened Steel （ 38~48HRC ） （ 30~38HRC ）
GR.6 Hardened Steel （ 48~56HRC ）
GR.7 Hardened Steel （ 56~68HRC ）
Work Material
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
ap (mm)
ae (mm)
ap (mm)
ae (mm)
ap (mm)
ae (mm)
ap (mm)
ae (mm)
Code No.
Dc×L1
F690TX 2×16 6,864 F690TX 2×20 6,160 F690TX 3×6 13,200 F690TX 3×8 12,320 F690TX 3×12 9,240 F690TX 3×16 8,096 F690TX 3×20 7,392 F690TX 3×25 6,600 F690TX 3×30 6,160 F690TX 4×8 8,800 F690TX 4×12 7,832 F690TX 4×16 6,952 F690TX 4×20 6,072 F690TX 4×25 5,456 F690TX 4×30 4,840 F690TX 4×40 4,048 F690TX 5×20 7,007 F690TX 5×40 5,606 F690TX 6×12 5,830 F690TX 6×18 5,170 F690TX 6×24 4,620 F690TX 6×36 4,070 F690TX 6×54 3,498
607 563
0.028 0.315 6,240 0.017 0.198 5,600 0.15 0.8 12,000 0.15 0.72 11,200
552 512
0.028 0.315 5616 0.017 0.198 5040
442 0.039 0.315 5,900 410 0.024 0.198 5,300
90 84
0.023 0.315 0.014 0.198 0.15 0.8 0.1 0.72 0.075 0.670 0.054 0.630 0.044 0.580 0.043 0.495 0.029 0.360 0.09 1.3 0.085 1.150 0.065 1.000 0.058 0.900 0.043 0.8 0.029 0.648 0.007 0.315 0.06 0.9 0.03 0.3 0.1 1.0 0.05 0.9 0.04 0.8 0.02 0.6 0.01 0.3
1,375 1,329
1,250 1,208
0.15 0.8 10800 1000 0.15 0.8 12,740 0.15 0.72 10080 966 0.15 0.72 12,000
300 270 200 173 150 146 118 230 215 205 198 175 144
1,012 0.1050.670 8,400
920 768 704 656 576 900 864 824 792 720 576 288 850 700 860 800 700 470 250
0.105 0.670 7560 0.081 0.630 6624 0.073 0.580 6048 0.065 0.495 5400 0.050 0.380 5040 0.1 1.2 7200 0.083 1.150 6408 0.065 1.000 5688 0.054 0.900 4968 0.043 0.8 4464 0.027 0.648 3960 0.007 0.315 3312 0.05 0.9 5733 0.01 0.3 4586 0.1 1.0 4770 0.05 0.9 4230 0.04 0.8 3780 0.02 0.6 3330 0.01 0.3 2862
736 0.105 0.670 9,000 614 0.081 0.630 7,900 563 0.073 0.580 7,100 525 0.065 0.495 6,400 461 0.050 0.380 6,000
845 774 722 634 990 950 906 871 792 634 317 935 770 946 880 770 517 275
0.081 0.630 7,360 0.073 0.580 6,720 0.065 0.495 6,000 0.050 0.380 5,600 0.1 1.2 8,000 0.083 1.150 7,120 0.065 1.000 6,320 0.054 0.900 5,520 0.043 0.8 4,960 0.027 0.648 4,400 0.007 0.315 3,680 0.05 0.9 6,370 0.01 0.3 5,096 0.1 1.0 5,300 0.05 0.9 4,700 0.04 0.8 4,200 0.02 0.6 3,700 0.01 0.3 3,180
720
0.1 1.2
7,963
691 0.120 1.150 6,400 659 0.100 1.000 5,600 634 0.080 0.900 4,900
576 0.065 0.8 461 0.04 0.6
4,500 3,900
230 0.01 0.315 3,300
72
680 0.05 0.9 560 0.01 0.3
6,370 5,733 5,308 4,778 4,247 3,716 3,185
250
90
688
0.1 1.0
200 160 130 120
640 0.05 0.9 560 0.04 0.8 376 0.02 0.6 200 0.01 0.3
90
（ mm ）
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
158
Made with FlippingBook - Online Brochure Maker