E110HX
Recommended Milling Conditions
Chamfering
GR.4 Hardened Steel （ 30~38HRC ）
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.8 Stainless Steel
GR.9 Cast Iron
GR.10 Aluminium
GR.11 Copper
GR.1 Carbon Steel
GR.15 Titanium
Work Material
30 ～ 60
25 ～ 70
15 ～ 40
25 ～ 50
30 ～ 80
100 ～ 200 100 ～ 200
15 ～ 30
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E110HX-1 E110HX-1.5 E110HX-2.0 E110HX-2.5 E110HX-3 E110HX-4 E110HX-5 E110HX-6 E110HX-8 E110HX-10 E110HX-12
1 14,3232,14814,3232,1487,957 47711,14083514,3232,14814,3232,14831,8304,7004,774 286 1.5 9,549 1,430 9,549 1,430 5300 318 7,427 557 9,549 1,430 9,549 1,430 21,220 3,183 3,183 190 2 7,1611,2807,1611,28039782385,5704177,1611,2807,1611,28015,9152,3872,387143 2.5 5,729 1,030 5,729 1,030 3183 238 4,456 400 5,729 1,030 5,729 1,030 12,732 1,900 1,909 114 3 4,774 1,000 4,774 1,000 2,652 198 3,713 334 4,774 1,000 4,774 1,000 10,610 1,591 1,591 100 4 3,978 835 3,978 835 2387 214 3,183 334 3,978 835 3,978 818 9,549 1,432 1,818 136 5 3,183 763 3,183 763 1910 200 2,546 305 3,183 763 3,183 835 7,639 1,145 1,591 119 6 2,917 612 2,917 612 1856 194 2,387 286 2,917 612 2,917 742 6,366 954 1,414 127 8 2,188 612 2,188 612 1392 194 1,790 286 2,188 612 2,188 763 5,570 1,114 1,273 114 10 1,750 612 1,750 612 1114 222 1,432 286 1,750 612 1,750 651 4,456 1,114 1,157 121 12 1,591 668 1,591 668 928 250 1,193 286 1,591 668 1,591 612 3,713 1,114 1,061 111
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
152
Made with FlippingBook - Online Brochure Maker