D425TX-2
Recommended Milling Conditions
Borehole parameters
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.1 Carbon Steel
GR.8 Stainless Steel
GR.9 Cast Iron
GR.12 鋁合金 Aluminium
Work Material
55~70
55~70
55~70
25~30
55~70
100~110
Vc m/min
RPM (min-1)
Feed (mm/rev)
RPM (min-1)
Feed (mm/rev)
RPM (min-1)
Feed (mm/rev)
RPM (min-1)
Feed (mm/rev)
RPM (min-1)
Feed (mm/rev)
RPM (min-1)
Feed (mm/rev)
Code No.
Dc
D425TX-2-1 D425TX-2-1.5 D425TX-2-2 D425TX-2-2.5 D425TX-2-3 D425TX-2-4 D425TX-2-5 D425TX-2-6 D425TX-2-7 D425TX-2-8 D425TX-2-9 D425TX-2-10 D425TX-2-11 D425TX-2-12 D425TX-2-13 D425TX-2-14 D425TX-2-15 D425TX-2-16
1 18,000 1.5 13,500 2 9,500 2.5 7,900 3 7,900 4 5,900 5 4,700 6 3,900 7 3,400 8 2,900 9 2,600 10 2,300 11 2,100 12 1,900 13 1,800 14 1,650 15 1,500 16 1,400
450 473 380 395 474 472 470 507 476 435 416 391 378 380 360 363 345 350
14,300 10,000
358 350 316 330 474 472 470 507 476 435 416 391 378 380 360 363 345 350
12,700
318 294 268 285 408 408 410 442 420 375 360 340 324 340 320 330 322 300
7,900 5,300 4,700 3,800 3,100 2,300 1,900 1,500 1,300 1,100 1,000
55 53 71 57
18,000 13,500
450 473 380 395 474 472 470 507 476 435 416 391 378 380 360 363 345 350
31,800 21,200 17,500 14,000 11,600 8,700 7,000
636 424 875 840 696 696 700 754 740 688 780 700 682 696 675 650 621 588
8,400 6,700 5,700 6,800 5,100 4,100 3,400 3,000 2,500 2,250 2,000 1,800 1,700 1,600 1,500 1,400 1,200
7,900 6,600 7,900 5,900 4,700 3,900 3,400 2,900 2,600 2,300 2,100 1,900 1,800 1,650 1,500 1,400
9,500 7,900 7,900 5,900 4,700 3,900 3,400 2,900 2,600 2,300 2,100 1,900 1,800 1,650 1,500 1,400
186 184 190 195 182 165 160 162 153 158 148 152 147 148
5,800 5,100 4,300 3,900 3,500 3,100 2,900 2,700 2,500 2,300 2,100
950 850 790 740 690 640 590
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0D
ap:2.0
（ mm ）
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid.
3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
208
Made with FlippingBook - Online Brochure Maker