Cutting Conditions
F636TX
F636TX
F518TX
F518TX
F517TX
F517TX
F517TX
F517TX
F517TX F518TX F636TX
Dc
Dc
Dc
Dc
Dc
Dc
Dc
Dc
ae=0.4xDc ae
ae=0.4xDc ae
ae=0.1xDc ae
ae=0.1xDc ae
ae=0.02xDc ae
ae=0.02xDc ae
ae ae=Dc
ae ae=Dc
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
Carbon Steel Materials
120 0.006xDc 120 0.006xDc 130 0.006xDc 140 0.007xDc 110 0.006xDc 120 0.006xDc 120 0.006xDc 120 0.006xDc
GR1 Carbon Steel
<24HRC Low-alloyed Steel <30HRC Hi-alloyed Steel 30~38HRC Hardened Steel 38~48HRC Hardened Steel
100 0.005xDc 100 0.005xDc 110 0.005xDc 120 0.006xDc 110 0.005xDc 100 0.005xDc 100 0.005xDc 120 0.005xDc
GR2
P
80 0.005xDc 80 0.005xDc 90 0.005xDc 100 0.006xDc 70 0.005xDc 80 0.005xDc 80 0.005xDc 80 0.005xDc Hardened Steel Materials
GR3
65 0.004xDc 90 0.003xDc 90 0.003xDc 100 0.003xDc 90 0.004xDc 100 0.003xDc 100 0.004xDc 90 0.003xDc
GR4
H
60 0.003xDc 80 0.003xDc 80 0.003xDc 90 0.003xDc 70 0.003xDc 90 0.003xDc 80 0.003xDc 80 0.003xDc Stainless Steel Materials
GR5
60 0.002xDc 70 0.004xDc 110 0.003xDc 130 0.003xDc 70 0.003xDc 80 0.004xDc 60 0.002xDc 70 0.004xDc
GR8-1 Ferritic 、 Martensitic
50 0.002xDc 60 0.003xDc 90 0.003xDc 100 0.003xDc 60 0.003xDc 70 0.003xDc 50 0.002xDc 60 0.003xDc
GR8-2 Austenitic
M
40 0.002xDc 50 0.003xDc 90 0.002xDc 60 0.002xDc 50 0.002xDc 60 0.003xDc 40 0.002xDc 50 0.003xDc
GR8-3 Austenitic-ferritic
Austenitic-ferritic Heat-resistant
30 0.002xDc 40 0.003xDc 40 0.002xDc 50 0.002xDc 40 0.002xDc 50 0.003xDc 30 0.002xDc 40 0.003xDc Cast Lron Materials
GR8-4
110 0.006xDc 110 0.006xDc 120 0.006xDc 130 0.007xDc 100 0.006xDc 130 0.005xDc 110 0.006xDc 110 0.006xDc
GR9-1 Grey cast iron
K
120 0.006xDc 120 0.006xDc 130 0.006xDc 140 0.007xDc 110 0.006xDc 140 0.005xDc 120 0.006xDc 120 0.006xDc
GR9-2 Nodular cast iron
All cutting data serve for orientation only and should be adapted individually to the technical conditions on location 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
224
Made with FlippingBook - Online Brochure Maker