Cutting Conditions
F515SX
F515SX
F514SX
F514SX
F514SX
F514SX
F514SX F515SX
Dc
Dc
Dc
Dc
Dc
Dc
ae=0.1xDc ae
ae=0.02xDc ae
ae=0.02xDc ae
ae=0.4xDc ae
ae=0.1xDc ae
ae ae=Dc
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
cutting speed Vc (m/min)
feed per tooth fz(mm)
Carbon Steel Materials
120
0.006×Dc
120
0.006×Dc
130
0.006×Dc
140
0.007×Dc
110
0.006×Dc
120
0.006×Dc
GR1 Carbon Steel
<24HRC Low-alloyed Steel <30HRC Hi-alloyed Steel 30~38HRC Hardened Steel 38~48HRC Hardened Steel
120
0.005×Dc
120
0.005×Dc
130
0.005×Dc
140
0.006×Dc
110
0.005×Dc
120
0.005×Dc
GR2
P
80
0.005×Dc
80
0.005×Dc
90
0.005×Dc
100
0.006×Dc
70
0.005×Dc
80
0.005×Dc
GR3
Hardened Steel Materials
65
0.004×Dc
90
0.003×Dc
90
0.003×Dc
100
0.003×Dc
90
0.004×Dc
100
0.003×Dc
GR4
H
60
0.003×Dc
80
0.003×Dc
80
0.003×Dc
90
0.003×Dc
70
0.003×Dc
80
0.003×Dc
GR5
Stainless Steel Materials
80
0.003×Dc
90
0.004×Dc
110
0.003×Dc
130
0.003×Dc
70
0.003×Dc
80
0.004×Dc
GR8-1 Ferritic 、 Martensitic
70
0.003×Dc
80
0.003×Dc
90
0.003×Dc
100
0.003×Dc
60
0.003×Dc
70
0.003×Dc
GR8-2 Austenitic
M
40
0.002×Dc
50
0.003×Dc
90
0.002×Dc
60
0.002×Dc
50
0.002×Dc
60
0.003×Dc
GR8-3 Austenitic-ferritic
Austenitic-ferritic Heat-resistant
30
0.002×Dc
40
0.003×Dc
40
0.002×Dc
50
0.002×Dc
40
0.002×Dc
50
0.003×Dc
GR8-4
Cast Iron Materials
110
0.006×Dc
110
0.006×Dc
120
0.006×Dc
130
0.007×Dc
100
0.006×Dc
110
0.005×Dc
GR9-1 Grey cast iron
K
120
0.006×Dc
120
0.006×Dc
130
0.006×Dc
140
0.007×Dc
110
0.006×Dc
120
0.005×Dc
GR9-2 Nodular cast iron
※ All cutting data are for reference only. Please adjust according to actual machining conditions. 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
266
Made with FlippingBook - Online Brochure Maker