Recommended Milling Conditions B219HX
Side Milling
GR.2 Low-alloyed Steel （ ~24HRC ）
GR.3 Hi-alloyed Steel （ ~30HRC ）
GR.4 Hardened Steel （ 30~38HRC ）
GR.8 Stainless Steel
GR.1 Carbon Steel
GR.9 Cast Iron
GR.10 Alumini - um
GR.15 Titanium
Work Material
164
131
98
82
82
164
328
82
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
B219HX-1/16 B219HX-5/64 B219HX-3/32 B219HX-1/8 B219HX-5/32 B219HX-3/16 B219HX-1/4 B219HX-5/16 B219HX-3/8 B219HX-1/2
1/16 10,028 5.01 8,010 4.01 5,992 1.44 5,014 0.40 5,014 0.30 10,028 5.01 20,056 12.03 5,014 0.30 5/64 8,025 4.81 6,410 3.85 4,795 1.53 4,012 0.64 4,012 0.64 8,025 4.81 16,050 12.84 4,012 0.64 3/32 6,689 4.68 5,343 3.74 3,997 2.40 3,344 1.00 3,344 0.80 6,689 4.68 13,378 16.05 3,344 0.80 1/8 5,014 9.23 4,005 7.37 2,996 5.51 2,507 2.01 2,507 1.70 5,014 9.23 10,028 32.09 2,507 1.70 5/32 4,018 12.86 3,209 7.70 2,401 5.76 2,009 3.21 2,009 2.41 4,018 12.86 8,035 32.14 2,009 2.41 3/16 3,343 15.78 2,670 8.54 1,997 6.39 1,671 4.01 1,671 2.67 3,343 15.78 6,685 32.09 1,671 2.67 1/4 2,507 15.04 2,003 8.81 1,498 6.59 1,254 4.51 1,254 3.01 2,507 15.04 5,014 30.08 1,254 3.01 5/16 2,006 15.24 1,602 9.61 1,198 7.19 1,003 5.21 1,003 4.01 2,006 15.24 4,011 30.49 1,003 4.01
3/8 1,671 15.38 1,335 10.15 999 7.59 1/2 1,254 15.54 1,001 10.81 749 8.09
836 5.68 627 6.02
836 4.68 1,671 15.38 3,343 33.43 836 4.68 627 5.01 1,254 15.54 2,507 35.10 627 5.01
※ All cutting data serve for orientation only and should be adapted individually to the technical conditions on location. 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
344
Made with FlippingBook - Online Brochure Maker