Cutting Conditions
R303
R301 / R302
R328 / R329
R320
R308 / R318 / R319
R308 R318 R319 R320 R328 R329 R301 R302 R303
Dc
Dc
Dc
Dc
Dc
cutting speed Vc (m/min)
feed per tooth Fn (mm/rev)
cutting speed Vc (m/min)
feed per tooth Fn (mm/rev)
cutting speed Vc (m/min)
feed per tooth Fn (mm/rev)
cutting speed Vc (m/min)
feed per tooth Fn (mm/rev)
cutting speed Vc (m/min)
feed per tooth Fn (mm/rev)
Carbon Steel Materials
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
GR1 Carbon Steel
<24HRC Low-alloyed Steel <30HRC Hi-alloyed Steel 30~38HRC Hardened Steel 38~48HRC Hardened Steel 48~55HRC Hardened Steel 55~68HRC Hardened Steel
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
15
0.008×Dc
GR2
P
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
GR3
Hardened Steel Materials
8
0.005×Dc
8
0.005×Dc
8
0.005×Dc
8
0.005×Dc
8
0.005×Dc
GR4
5
0.003×Dc
5
0.003×Dc
5
0.003×Dc
5
0.003×Dc
5
0.003×Dc
GR5
H
GR6
GR7
Stainless Steel Materials
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
GR8-1 Ferritic 、 Martensitic
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
GR8-2 Austenitic
M
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
12
0.006×Dc
GR8-3 Austenitic-ferritic
Austenitic-ferritic Heat-resistant
8
0.004×Dc
8
0.004×Dc
8
0.004×Dc
8
0.004×Dc
8
0.004×Dc
GR8-4
Cast Iron Materials
15
0.006×Dc
15
0.006×Dc
15
0.009×Dc
15
0.006×Dc
15
0.009×Dc
GR9-1 Grey cast iron
K
15
0.006×Dc
15
0.006×Dc
15
0.009×Dc
15
0.006×Dc
15
0.009×Dc
GR9-2 Nodular cast iron
Aluminium Steel Materials
Wrought Aluminium alloys Aluminium cast alloys <10% Aluminium cast alloys >10%
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
GR10-1
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
GR10-2
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
20
0.006×Dc
GR10-3
N
Copper Steel Materials
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
GR11-1 Pure Copper
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
GR11-2 Brass
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
15
0.006×Dc
GR11-2 Bronze
※ All cutting data serve for orientation only and should be adapted individually to the technical conditions on location . 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
494
Made with FlippingBook - Online Brochure Maker