E235-2.5SX
Recommended Milling Conditions
Side Milling
GR.4/GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1/GR.2/GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.16 Nickel
GR.17 High Temp Alloys
Work Material
140
100
80
80
50
30
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E235-2.5SX-6 6 E235-2.5SX-8 8 E235-2.5SX-10 10 E235-2.5SX-12 12 E235-2.5SX-16 16 E235-2.5SX-20 20
7,432 5,574 4,459 3,716 2,787 2,230
1,858 1,672 1,561 1,486 1,254 1,115
5,308 3,981 3,185 2,654 1,991 1,593
1,062
4,247 1,062 4,247 1,062 2,654 531 1,593 319 3,185 956 3,185 1,115 1,991 448 1,194 299
995 956 929 697 637
2,548 892 2,548 1,019 1,593 438 2,123 849 2,123 956 1,327 398
956 796 597 478
287 279 239 191
1,593 717 1,593 796 1,274 637 1,274 637
995 796
299 279
ap:2.0D
ap:2.0D
ap:2.0D ap:2.0D ap:2.0D ap:2.0D
（ mm ）
ae:0.12D
ae:0.1D
ae:0.1D ae:0.05D ae:0.05D ae:0.05D
High Speed Side Milling
GR.4/GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1/GR.2/GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.16 Nickel
GR.17 High Temp Alloys
Work Material
200
160
130
130
100
80
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E235-2.5SX-6 6 E235-2.5SX-8 8 E235-2.5SX-10 10 E235-2.5SX-12 12 E235-2.5SX-16 16 E235-2.5SX-20 20
10,617
3,716 3,185 2,867 2,654 2,190 1,911
8,493 6,370 5,096 4,247 3,185 2,548
1,699 1,593 2,038 2,123 1,593 1,529
6,901 1,725 6,901 1,035 5,308 796 4,247 637 5,176 1,553 5,176 1,035 3,981 597 3,185 637 4,141 1,449 4,141 1,242 3,185 478 2,548 764 3,450 1,380 3,450 1,121 2,654 398 2,123 690 2,588 1,165 2,588 906 1,991 299 1,593 557 2,070 1,035 2,070 828 1,593 239 1,274 510
7,963 6,370 5,308 3,981 3,185
ap:2.0D
ap:2.0D
ap:2.0D ap:2.0D ap:2.0D ap:2.0D
（ mm ）
ae:0.1D
ae:0.05D
ae:0.1D ae:0.05D ae:0.05D ae:0.05D
1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
58
Made with FlippingBook - Online Brochure Maker