E236-2.5SX / 4.0SX
Recommended Milling Conditions
Side Milling
GR.4/GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1/GR.2/GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.16 Nickel
GR.17 High Temp Alloys
Work Material
140
100
80
80
50
30
Vc m/min
E236-2.5SX-6 6 E236-2.5SX-8 8 E236-2.5SX-10 10 E236-2.5SX-12 12 E236-2.5SX-16 16 E236-2.5SX-20 20
7,432 5,574 4,459 3,716 2,787 2,230
2,601 2,341 2,185 2,081 1,756 1,561
5,308 3,981 3,185 2,654 1,991 1,593
1,486 1,393 1,338 1,301
4,247 1,486 4,247 1,486 2,654 743 1,593 446 3,185 1,338 3,185 1,561 1,991 627 1,194 418
2,548 1,249 2,548 1,427 1,593 613 2,123 1,189 2,123 1,338 1,327 557
956 796 597 478
401 390 334 268
975 892
1,593 1,003 1,593 1,115 995
418 390
1,274 892 1,274 892
796
ap:2.0D
ap:2.0D
ap:2.0D ap:2.0D ap:2.0D ap:2.0D
（ mm ）
ae:0.12D
ae:0.1D
ae:0.1D ae:0.05D ae:0.05D ae:0.05D
High Speed Side Milling
GR.4/GR.5 Hardened Steel/Hardened Steel (30 ～ 38HRC ） （ 38 ～ 48HRC ）
GR.1/GR.2/GR.3 Carbon Steels/Low-alloyed Steel/Hi-alloyed Steel （～ 24HRC ） （～ 30HRC ）
GR.8 Stainless Steel
GR.15 Titanium
GR.16 Nickel
GR.17 High Temp Alloys
Work Material
200
160
130
130
100
80
Vc m/min
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
RPM (min-1)
Feed (mm/min)
Code No.
Dc
E236-2.5SX-6 6 E236-2.5SX-8 8 E236-2.5SX-10 10 E236-2.5SX-12 12 E236-2.5SX-16 16 E236-2.5SX-20 20
10,617
5,202 4,459 4,013 3,716 3,066 2,675
8,493 6,370 5,096 4,247 3,185 2,548
2,378 2,230 2,854 2,973 2,230 2,140
6,901 2,415 6,901 1,449 5,308 1,115 4,247 892 5,176 2,174 5,176 1,449 3,981 836 3,185 892 4,141 2,029 4,141 1,739 3,185 669 2,548 1,070 3,450 1,932 3,450 1,570 2,654 557 2,123 966 2,588 1,630 2,588 1,268 1,991 418 1,593 780 2,070 1,449 2,070 1,159 1,593 334 1,274 713
7,963 6,370 5,308 3,981 3,185
ap:2.0D
ap:2.0D
ap:2.0D ap:2.0D ap:2.0D ap:2.0D
（ mm ）
ae:0.1D
ae:0.05D
ae:0.1D ae:0.05D ae:0.05D ae:0.05D
※ Notice: E236-4.0SX is Long Length series End Mills. Please adjust the parameter according. 1. Please work with good rigidity / high precision facilities and collet chuck. 2. Please choose proper cutting fluid. 3. The cutting data is reference value only. Please adjust it according to your real working conditions. 4. If RPM is lower than the reference value, the Feed rate (fz) and RPM should be reduced by the same proportion. 5. If vibration occurs during cutting, please reduce cutting parameter.
60
Made with FlippingBook - Online Brochure Maker