M.D.I. Frese a filettare ISO 60° HM Threading mills type ISO 60° VHM-Fräser zum schneiden von ISO-gewinden 60° M.D.I. fraises a fileter ISO 60°
FMSR ... N
RIVESTIM. COATED TIALN
TOLLERANZE
D
d
10°
GENERICO / ALL PURPOSE
TOLLERANCE RANGE
e8
h6
ØD = 3,10 - 20
H
MG
L1
ØD
Ød
P
> PER FILETTATURE ISO 60° > ATTACCO DIN 6535 HA > RIVESTIMENTO TIALN
> FOR ISO 60° THREAD > SHANK DIN 6535 HA > TIALN COATED
(mm) ØD
Filetti utili T hread useful
Preforo d. Prebore
Filetto eseguibile Thread type
ART.
L1
3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 Z
Ød
H ±1
0,70 0,80 0,75 1,00 0,75 1,00 1,25 0,75 1,00 1,25 1,50 1,75 1,00 1,25 1,50 2,00 1,00 1,50 2,00 1,00 1,50 2,00 2,50 1,00 1,50 2,00 2,50 1,00 1,50 2,00 3,00 P/mm
FMSR 031.070 N FMSR 040.080 N FMSR 045.075 N FMSR 045.100 N FMSR 060.075 N FMSR 060.100 N FMSR 060.125 N FMSR 080.075 N FMSR 080.100 N FMSR 080.125 N FMSR 080.150 N FMSR 080.175 N FMSR 100.100 N FMSR 100.125 N FMSR 100.150 N FMSR 100.200 N FMSR 120.100 N FMSR 120.150 N FMSR 120.200 N FMSR 140.100 N FMSR 140.150 N FMSR 140.200 N FMSR 140.250 N FMSR 160.100 N FMSR 160.150 N FMSR 160.200 N FMSR 160.250 N FMSR 200.100 N FMSR 200.150 N FMSR 200.200 N FMSR 200.300 N
3,1 4,0 4,5 4,5 6,0 6,0 6,0 8,0 8,0 8,0 8,0 8,0
6 6 6 6 6 6 6 8 8 8 8 8
55 55 55 55 55 55 55 66 66 66 66 66 80 80 80 80 82 82 82
8
11 15 16 12 20 15 12 26 20 16 13 11 25 20 16 12 30 20 15 35 23 17 14 40 26 20 16 40 26 20 13
3,3 4,2 8,3 5-6 7,2
M4 M5
12 12 12 15 15 15 20 20 20 20 20 25 25 25 25 30 30 30 35 35 35 35 40 40 40 40 40 40 40 40
MF9
M6-M7
MF8 MF8
7
6,8-7,8-8,8
M8-M9-MF10 MF10-MF12 MF10-MF12
9,2-11,2
9-11
9
MF10
8,5-9,5-10,5
M10-M11-MF12
10,2
M12
10,0 10,0 10,0 10,0 12,0 12,0 12,0 14,0 14,0 14,0 14,0 16,0 16,0 16,0 16,0 20,0 20,0 20,0 20,0
10 10 10 10 12 12 12 14 14 14 14 16 16 16 16 20 20 20 20
11
MF12 MF14 MF14
12,8 12,5
12 13
M14
MF14 MF16
14,5
14 15
M16
100 100 100 100 100 100 100 100 110 110 110 110
MF16 MF18 MF18
16,5
16
15,5
M18
17-19
MF18-MF20 MF20-MF22 MF20-MF22
18,5-20,5
18-20
17,5-19,5
M20-M22
21>
MF22> MF24> MF24> MF24>
22,5>
22> 21>
- Per filettature interne usare un diametro fresa non superiore ai 2/3 del diametro del filetto, per i filetti a passo fine 3/4. Per filettatu- re esterne il diametro fresa non deve essere superiore al diametro del filetto. - For inner threading use a milling cutter diameter no greater than 2/3 of the diameter of the thread, for fine thread pitches use 3/4. For outer threading the milling cutter diameter must not be greater than the diameter of the thread.
PARAMETRI DI TAGLIO A PAG. 1175 CUTTING DATA ON PAGE 1175 SCHNTTPARAMETER AUF SEITE 1175 PARAMETRES DE COUPE PAGE 1175
? PAG. 1176
820
Made with FlippingBook - Online Brochure Maker