2920D 2940D 3PL Non Folding Wing Operator Safety Manual

2900SPEEDTILLER 3 POINT LINKAGE

OPERATOR & SAFETY MANUAL

RIGID - NON-FOLDINGWINGMODELS: 2920,2922, 2925, 2930, 2935 & 2940D

1023 W 9th St | PO Box 248, Grafton, ND 58237 | USA 74 Young Rd | PO Box 340 ,Cowra, NSW 2794 | AUS

© K-Line Ag 2019

Wou ld you l i ke a copy of th i s manual emai l ed to you?

Send your reques t to mar ket i ng@k- l i ne . net .au or scan here :

Dear Customer

Thank you for purchasing a Three Point Linkage Speedtiller Poweflex® made by K-Line Industries. We would like to assure you that you have made a good choice, and will be able to rely on this high quality piece of equipment. We ask you to follow the user’s instructions closely, as this will ensure that you experience the benefits of using the machine without experiencing the unnecessary down time caused by misuse. When you receive the machine, make sure that it has not been damaged during transportation and that no parts are missing. Contact your dealer immediately if any parts are missing. Ensure that all components are correctly adjusted. The return of the Warranty Registration Form Page 46 will enable a prompt and efficient identification of your Speedtiller and attention to any concern you may have. Before operating PLEASE TAKE THE TIME TO LEARN the process of operation. Do not take the unit for granted; ease into becoming familiar with your new equipment. The operator should be a responsible adult familiar with farm machinery and trained for this purpose. Do NOT allow persons to operate or assemble the unit until they have read this manual and understand how to use this machine, and observe the safety precautions. Never exceed the limits of this machine. If its ability to do a job, or to do so safely, is in question - DO NOT TRY IT.

DO NOT attempt to operate this equipment under the influence of drugs or alcohol.

Remember - Your best assurance against accidents is a careful and responsible operator.

If you have any questions not answered in this manual or require additional copies or the manual is damaged, please contact your dealer or be free to phone us on our free call number:

USA - 1800 445 6882 AUS - 1800 194 131

The team here at K-Line Agriculture trust you enjoy a good season and prove the benefits of owning and operating a quality machine that is built to perform.

Signed:

James Larsen General Manager

LEGAL DISCLAIMER LAST UPDATED: 04/10/19

The information contained in the K-Line Industries Pty Ltd (also trading as “K-Line Ag” and “K-Line Agriculture”) manual is for general information purposes only. K-Line Industries Pty Ltd assumes no responsibility for errors or omissions in the contents on the book. In no event shall K-Line Industries Pty Ltd be liable for any special, direct, indirect, consequential, or incidental damages or any damages whatsoever, whether in an action of contract, negligence with the use of the Service or the contents of the Service. K-Line Industries Pty Ltd reserves the right to make additions, deletions, or modification to the contents of this manual at any time without prior notice.

4

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

OP & SAFETY MANUAL Table Of Contents CUSTOMER LETTER 3 LEGAL DISCLAIMER 4 SPECIFICATIONS 6 Tracking Adjustments Front Disc Gang Lateral Positioning Front Disc Standard Factory Setting Adjustment Procedure

22

23-25

24 25 25 25 26

Side Coulter Adjustment Excessive Trash Conditions Maintenance & Safe Procedures

INTRODUCTION

7 7 7 7 7

Identifying The Machine Tractor Requirements

Definitions Used In This Manual Availability Of Genuine Parts

EXPLODED VIEWS

27-31

RISK MANAGEMENT

8-10

Speedtiller Jump Arm Assembly

27 28 29 30

Identifying Hazards

8 8 8 8 9

Disc Arm Bearing

Monitor & Review Control Measures

Side Coulter

Risk Assessment

50mm Roller Bearing Shaft Heavy Duty Roller Bearing

Risk Control

31

Risk Assessment Score Chart

Rear Roller Bearing Fitting instructions

32

Risk Assessment Table

10

SAFETY

11-18

Bolt Torque Tables

33-34

Safety Precautions

11

Important Notice (MUST READ)

12 13 13 14 15 16 17 18

SAFETY DECALS

35-39

Safety Alert Symbol

Safety Sign Care

35 36

Signal Words

Safety Decal Placement & Quantities

Instruction For Safe Operation

Decals

37-38

Tire Pressures & Safety Attaching To Machine

Logo Decal placement & Quantities

39

Safe Operation In Field/Transport/ Roading

TESTIMONIAL PERMISSION FORM 40-41

Transporting/ Roading

WARRANTY Warranty Letter

44-46

FIELD OPERATION Speedtiller Start-Ups Performing Maintenance

19-26

44 46

19

Warranty Registration Form

20

Useful Hints

21

END OF DOCUMENT

48

5

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

3 P L NON - FOLDED S P EC I F I CAT I ONS

RIGID MODEL SIZES

2920D 2922D

2925D

2930D 2935D 2940D

2.0M (6.6FT)

2.25M (7.4FT)

2.5M (8.2FT)

3.0M (9.8 FT)

3.5M (11.5FT)

4.0M (13.1FT)

OPERATING WIDTH APPROX.

80-105KW 110-140HP

90-110KW 130- 150HP

50-75KW 70-90HP

60-80KW 80-105 HP

70-90KW 90-120HP

111-164KW 150-220HP

TRACTOR POWER RANGE

16

18

20

24

28

32

NUMBER OF DISCS

SPEEDTILLER WEIGHT DEPENDING ON ROLLER ETC.

1532KG 3378LB

1646KG 3629LB

1790KG 3947LB

2048KG 4516LB

2356KG 5195LB

2814KG 6205 LB

TOWING TRANSPORT HEIGHT

-

-

-

-

-

-

-

-

-

-

-

-

TRANSPORT HEIGHT

2.3M (7.5FT)

2.5M (8.2FT)

2.8M (8.5FT)

3.3M (12.5FT)

3.8M (12.5FT) 2.4M (7.9FT)

4.3M (14.1FT)

TRANSPORT WIDTH

2.4M (7.9FT) 2.4M (7.9FT) 2.4M (7.9FT)

2.4M (7.9FT)

2.4M (7.9FT)

TRANSPORT LENGTH

Figure 1

6

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

AFTER DELIVERY

When you receive themachine, make sure that it has not been damaged during transportation and that no parts are missing. Only by giving us immediate advice can the necessary replacement parts be obtained. Ensure that all components are correctly adjusted.

GENUINE PARTS

K-Line spare parts and accessories have been specifically designed and developed for the machines produced. We would call your attention to the fact that non-genuine parts and accessories are not recommended by K-Line. The use of such replacement parts frees K-Line from all liability and makes the warranty void. The installation and/or use of non-genuine parts may, because of technical characteristics of construction, modify or influence the performance of the machine negatively.

IDENTIFYING THE MACHINE FOR REQUESTING SPARE PARTS

The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate the model and number of your equipment to ensure prompt and efficient attention.

TRACTOR REQUIREMENTS

10-14 Horsepower x width of machine in feet 25-35 Kilowatt x meter width of machine in meters Tractor weight must be same as or greater than the towed unit.

Hydraulic valves

1 x Double spool (optional) 2800 PSI approximately

Hydraulic operating pressure

DEFINITIONS USED IN THIS MANUAL

DISC ARM IDENTIFICATION (REAR VIEW)

VIEW FROM REAR OF MACHINE

FRONT ARM

REAR ARM

BOLT TENSION

Top plate bolt tension 200ft lbs/280nm

Disc bolt tension 250ft lbs/340nm

Figure 2

Figure 3

Figure 4

7

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

R I S K M A N A G E M E N T

Risk management is the process of finding out what may cause an injury, deciding what may happen as a result, and doing something about it.

The steps of risk management are: • Identify the hazards to workplace health and safety arising from work activities • Assess the risks

• Determine and implement control measures to reduce risk • Monitor and review the effectiveness of the control measures IDENTIFYING HAZARDS

Prior to commencing work, all hazards related to the work tasks should be identified. The selection of the appropriate work procedure(s) will depend on the type of work procedure(s) and hazards involved. Regular safety inspections will also identify hazards and ensure that control measures are in place. RISK ASSESSMENT Risk assessment allows appropriate control measures to be developed. Once hazards have been identified, they should be assessed in terms of their potential to do harm. To assess risk, consideration should be given to probability and consequences. (SEE RISK ASSESSMENT SCORE CHART - Pg 9). RISK CONTROL Risk control is the process of eliminating or reducing risk factors. Control measures should be chosen and implemented to eliminate or reduce risk as far as practicable. When deciding on the most appro- priate measures to use, practicality and acceptance of the control measures should be considered. Safe Working Procedures will be developed for all high – medium risk hazards. MONITOR AND REVIEW CONTROL MEASURES The risk identification, assessment and control process requires regular monitoring to ensure the implemented control measures perform as originally intended and continue to prevent or adequately control the risk of injury or incident. Control measures should also be checked carefully to ensure that new hazards are not created, directly or indirectly, by the original control measures.

8

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

R I S K A S S E S S M E N T S C O R E C H A R T

Figure 5

AT ALL TIMES COMPLY WITH RECOMMENDATIONS AND REQUIREMENTS OF THE MANUFACTURER AND THE ENVIRONMENTAL PROTECTION AUTHORITY

9

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

R I S K A S S E S S M E N T

CONT I NUED

RISK SCORE

REVISED RISK SCORE

CODE

HAZARDS

CONTROL

ADJUSTING & CLEANING MUST ONLY BE DONE WHEN MACHINE IS LOWERED OR IN TRANSPORT POSITION AND ONLY AFTER ALL CHAINS AND BOLTS HAVE BEEN CHECKED FOR TIGHTNESS & WEAR IN THE LOWER POSITION. ENSURE JACK IS INSTALLED CORRECTLY & JACK RECEIVES REGULAR MAINTENANCE. KEEP FEET AND BODY CLEAR WHEN OPERATING. ENSURE NO PERSONNEL ARE BETWEEN TRACTOR & HARROW BAR WHEN HITCH- ING TRACTOR MACHINE MUST BE LOWERED INTO WORKING POSITION USING SUITABLE LIFTING EQUIPMENT BEFORE PRIMING IS EFFECTED BY SLIGHTLY LOOSENING FITTING/S INTO CYLINDERS AND OPERATING TRACTOR HYDRAULICS TO ACHIEVE FULL UNINTERRUPTED TRAVEL OF CYLINDER SEVERAL TIMES. THEN RE-TIGHTEN HYDRAULIC TINE FITTINGS ENSURE ALL THREE JACKS ARE CORRECTLY POSITIONED AND TAKING WEIGHT BEFORE REMOVING DRAWBAR PIN. STICKERS WARN OPERATOR MAINTAIN REGULAR CHECKS ON HYDRAULIC SYSTEM FOR WEAR & CHECK ALL FITTINGS ARE SECURE ENSURE TRACTOR OIL FLOW IS LIMITED TO REDUCE FALLING SPEED OR DO NOT INTERRUPT MACHINE FALLING UNTIL MACHINE IS FULLY IN LOWERED POSITION SAFETY PINS MUST BE PUT IN PLACE AS SOON AS MACHINE IS PUT IN TRANSPORT POSITION AND IF TRAVELLING ON PUBLIC ROADS TO DISCONNECT HYDRAULICS FROM TRACTOR

CRUSHING - WHEN ADJUSTING AND CLEANING, AS MACHINE MAY DROP WITHOUT WARNING

1

5

1(A).

CRUSHING - IMPROPER USE OF JACK

1

5

1(B).

CRUSHING - WHEN HITCHING TRACTOR

2

5

1(C).

CRUSHING - PRIOR TO PRIMING HYDRAULIC SYSTEM, AS MACHINE MAY DROP WITHOUT WARNING

1

5

1(D).

SUDDEN LIFT OF DRAWBAR CAUSING SEVERE INJURY, IF MACHINE BECOMES UNHITCHED PENETRATION OF OIL - BROKEN OR BADLY MAINTAINED HYDRAULIC LINES RUPTURE OF OIL LINES BY OVER PRESSURE WHEN MACHINE COMES TO SUDDEN STOP BEFORE

1

5

1(E).

2

5

2(A).

2

5

2(B).

FULLY LOWERED TO WORKING POSITION

COLLISION - HYDRAULICS ACCIDENTALLY LOWERED WHEN MACHINE IS BEING OPERATED IN TRANSPORT

1

5

3.

Figure 6

ALL HAZARDS & RISKS ARE CONTROLLED THROUGH SAFE WORKING PROCEDURES & ADEQUATE SIGNAGE

10

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

WARNING! ! ! SAFETY PRECAUTIONS

FAI LURE TO OBSERVE THE FOLLOWING INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH

It is the responsibility of the purchaser to:

• Maintain in as new condition all warning and safety signs and devices at all time.

• Consult electricity authorities and all relevent energy companies to determine safe working distances from overhead power lines etc BEFORE operation of the machine. POWER LINES CAN ARC AND ELECTROCUTE WITHOUT COMING IN CONTACT!!! • Ensure all operators are familiar with this manual and all safety devices and features of the machine.

• Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine.

• Maintain the machine at all times in a condition that is safe to operate, and ensure strength and balance of machine is adequate to accommodate the K-Line products you have purchased. • Must conduct a risk assessment, taking all risks into consideration before comissioning machine for use.

11

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

It is the responsibility of the operators to: Read and understand your manual. Take time to familiarize yourself with the operation of this machine, particularly the safety signs and devices fitted to this machine.

USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY.

Slow down in terrain such as rocks, or other difficult operating conditions.

I MPORTANT NOT I C E

• Safe work procedure analysis must be performed before attempting to assemble this machine.

• Do not attempt to operate this equipment under the influence of Drugs & Alcohol. • K-Line Ag can not be held responsible for any injury, death or property damage in the process of assembling this machine.

For further information please contact :

US: 1800 445 6882 AU: 1800 194 131

• Ensure hydraulic system is full primed.

12

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S A F E T Y A L E R T ! ! S A F E T Y . . . Y O U C A N L I V E W I T H I T

YOUR SAFETY AND THE SAFETY OF OTHERS IS IMPORTANT

• BE PREPARED! • BE SAFE! • BE AWARE! • BE SEEN!

When you see this symbol, you must be alert to the possibility of injury or death. SAFETY ALERT SYMBOL

SIGNAL WORDS

The use of signal words, DANGER , WARNING AND CAUTION relating to the safety messages. The appropriate signal word is selected when using the following guidelines.

Indicates an imminently hazardous situation that if not avoided, WILL result in serious injury or death if proper safety measures are not taken.

Indicates a potentially hazardous situation that, if not avoided COULD result in serious injury or death if proper safety measures are not taken .

Indicates potentially hazardous situation that, if not avoided MAY result in serious injury or death if proper safety measures are not taken.

ALL OPERATORS MUST UNDERSTAND AND ABIDE BY MAINTENANCE SAFETY PROCEDURES SET OUT IN THIS BOOK. IT IS THE RESPONSIBILITY OF THE ASSEMBLER TO ATTACH ALL SAFETY SIGNS AND DEVICES TO THIS MACHINE. FAILURE TO OBSERVE THE INSTRUCTIONS OF THIS BOOKLET COULD RESULT IN SERIOUS INJURY OR DEATH.

13

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

INSTRUCTIONS FOR SAFE OPERATION

The machine should not be driven, maintained or repaired by people who are not aware of the contents of this Risk Document. This User’s Manual should be read and understood by all those who use, adjust or control the machine. These safety instructions should be passed onto other users. 1. BE SURE tractor drawbar pin is locked securely in place. 2. Make SURE all personnel are clear of machine when folding/unfolding & when in operation. 3. DO NOT operate unit while people are within 20 metres. 4. KEEP CLEAR of machine when in working & lifted position - AT ALL TIMES. 5. Hydraulic lines & hoses operate under extremely high pressure & if damaged or worn MUST be repaired IMMEDIATELY. 6. Keep HANDS & BODY CLEAR of any oil leakage as high pressure oil can penetrate the skin. 7. All bolts, nuts & pins MUST be well secured. 8. DO NOT stand on or ride on machine. 9. NEVER get under or on top of machine when it is supported by jack and KEEP LEFT & BODY CLEAR when operating jack. 10. NEVER alter the depth control or change to or from transport position, while another person adjusts safety pins. 11. This machine has not been designed or built for road use. Please consult State Police, Roads & Traffic Authority and any other relevant authorities regarding the roads concerned when in transit. 12. DO NOT operate if any part of this machine is within 10 metres of overhead power lines. 13. SPEED LIMIT - Subject to permit regulations, local government Authorities, road surface conditions & prime mover towing recommendations. Maximum towing speed is 40km/hr. DO NOT EXCEED AT ANY TIME. I MPORTANT K-LINE INDUSTRIES Spare parts and accessories have been specifically designed and developed for the machines produced. We call your attention to the fact that non genuine parts and accessories are not recommended by K-LINE INDUSTRIES. The use of such replacement parts frees K-LINE INDUSTRIES from all liability and makes the warranty void. The installation and/or use of non genuine parts may, because of the technical characteristics of construction, modify or influence the performance of the machine negatively. 14. TIRE PRESSURE - Consult recommended tire pressure table. 15. Before operation, all hydraulic cylinders must be primed.

REMEMBER AN IMPLEMENT WITH NO BRAKES REQUIRES CAUTION & COMPETENCE

14

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

TIRE SAFETY & PRESSURES

• Always cage tires before seating beads. • Never exceed stated pressures when seating beads. • Do not attempt to mount a tire unless you have the suitable equipment and experienced personnel. • Inflating tires can be dangerous. Always stand to the side when inflating. • Failure to comply could result in serious injury or death. • Load ratings of replacement tires should meet or exceed weight require- ments. • Correct pressure is 90PSI / 413KPA (Center) 75PSI / 344KPA (Wing) • Before mounting wheel to machine, check all hub and rim contact surfaces are undamaged and free of paint, dirt and grease. • Lubricate wheel stubs with standard viscosity oil. • Tension wheel nuts to 350ft lbs / 474nm. • For field operation: Re-tension after first, fifth, then every fifty hours of op- eration. • For road travel re-tension first 3miles (5kms), 10miles (15kms), and thereafter at 25miles (40kms) intervals

SERVICING PROCEDURES

- ALWAYS CAGE TIRES BEFORE SEATING BEADS. - NEVER EXCEED STATES PRESSURES WHEN SEATING BEADS. FAILURE TO COMPLY COULD RESULT IN SERIOUS INJURY OR DEATH

Figure 7

Figure 8

TIRE PRESSURE Center: 90PSI / 413KPA Wing: 75PSI / 344KPA Wheel nut tension: 350ft lbs / 47nm

Figure 9

15

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S A F E T Y

AT TA C H I N G T O M A C H I N E

1. Keep well clear when backing up to machine. 2. Shut down tractor. 3. Secure all 3 Point Linkage safety locks & lock drawbar pin in place. 4. Lock up 3 point linkage anti sway stabiliser system on tractor. 5. Both linkage arms must be set level. 6. Plug in electrical lead to tractor connection (if provided) . HITCHING TO TRACTOR N.B. keep body well clear when attaching tractor to machine at all times. Follow all safety precautions set out on preceding pages

Figure 10

16

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S A F E T Y

SAFE OPERATION IN FIELD & TRANSPORT/ROADING

IT IS THE RESPONSIBILITY OF THE OPERATORS TO: • READ AND UNDERSTAND YOUR MANUAL. • TAKE TIME TO FAMILIARIZE YOURSELF WITH THE OPERATION OF THIS MACHINE, PARTICULARLY THE SAFETY SIGNS AND DEVICES FITTED TO THIS MACHINE. USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY. Slowdown in terrain such as rocks or other difficult operating conditions.

POWER LINES CAN ARC AND ELECTROCUTE WITHOUT COMING IN DIRECT CONTACT

Figure 11

Consult electricity authorities and all relevant energy companies to determine safe working distances from overhead power lines etc. BEFORE operation of this machine. • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine. • Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations.

17

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S A F E T Y

BEWARE OF VERTICAL AND HORIZONTAL CLEARANCES NEEDED WHEN UNFOLDING WINGS.

BEWARE OF PINCH POINTS IN WING LIFT AREA WHEN SECURING OR

RELEASING SAFETY LOCKS.

KEEP ALL PERSONNEL WELL CLEAR OF WING RADIUS WHEN

UNFOLDING OR LOWERING WINGS AND REAR MODULE.

TRANSPORTING/ ROADING 1. Tractor manufacturer specifications must comply for weight and suitability of rear mounted implements. 2. Lock up 3 Point Linkage anti sway stabiliser system on tractor 3. Ensure tractor tires are correctly inflated 4. Ensure safety locks and pins are engaged. 5. Keep brake pedals latched together at all times 6. Plan your route to avoid heavy traffic 7. Observe bridge load ratings 8. TIP OVER HAZARD this is an unbraked implement. Use extreme caution when turning and on steep terrain. 9. Maximum towing speed is 20mph (32km/hr ). DO NOT EXCEED AT ANY TIME.

Figure 13

Figure 12

18

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S P E E D T I L L E R S T A R T - U P T I P S Ⓡ

THIS IS A GUIDE ONLY AND MUST BE READ IN CONJUNCTION WITH INSTRUCTION MANUAL 1) TILT ADJUSTMENT (SETTING TO REDUCE SIDEWAYS TRACKING) • Start with front disc 20mm higher than back discs. • Follow diagram for tilt settings. pg 20 • To adjust -turn top link and lock.

FRONT LATERAL DISC POSITIONING IS FACTORY SET. See pg 22 for adjustment setting.

2) SPEED RANGE • 8-15kph. (5.9mph) • Greater activity occurs at higher speeds.

HEADLANDS/ TURNING • Always raise machine when on headlands and when turning. 3) ROAD TRAVEL SPEED LIMIT • 32kmh (20mph) 4) Ensure wings are locked out during operation. (2940T - 2985T)

19

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

P E R F O R M I N G M A I N T E N A N C E

DAILY MAINTENANCE CHECK FOR OPTIMUM PERFORMANCE

Before Starting Work:

Disc bolts - Check first 10hrs of operation

1. For field operation: Re-tension after 1st, 5th, then every 50 hrs of operation. 2. For road travel re-tension first 3miles (5kms), 10miles (15kms), and thereafter at 25miles (40kms) intervals. 3. Check discs and disc bolt tension to specified torque 250ft lb / 340nm. 4. Check for damaged, worn and fatigued parts. Have machine repaired if necessary. 5. Ensure all appropriate safety decals are securely attached to machine – Page 35. 6. Check all safety mechanisms are in place and operating correctly. 7. Lubricate rear roller bearings – Refer to Page 32 8. Instruction manual has been read, understood and stored with machine. Always reset adjustments after changing disc blades.

Figure 14

Starting work Machine must be: •

Lowered to ground

OR, •

Placed in raised position with all safety locks engaged and engine shut down before performing any field adjustements, failure to comply could result in serious injury or death. Set machine on level surface • Ensure both tractor 2 point linkage arms are correctly adjusted for level working. • Adjust roller 1” or 25mm above surface • Preliminarily adjust tilt approx. 3/4” or 20mm higher at front. Run at operating speed and check adjustments in this order: • Tracking in line • Lateral front disc adjustment • Adjust for depth of cut gradually • Check coulter setting for best furrow filling

Disc arm locating bolts - Check first 10hrs of operation

Figure 15

*NB - Ensure that all discs engage with the soil for positive rotation. Where heavy trash conditions and loose soils are encountered, machine may have to yore sideways slightly to achieve the desired result.

20

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

F I E L D O P E R AT I O N

U S E F U L H I N T S 1. Machine digging too shallow on right hand side • Lower right hand tractor linkage arm. 2. Cross working at 15 degrees off line gives better leveling and trash clearance. 3. Full ground disturbance starts at 2.5 inches.(60 mm) Adjustment should be made to compensate for disc wear and concavity. • To improve weed control and for better soil disturbance • Adjust lateral disc positioning • Ensure machine is traveling in line • Increase depth of cut • Replace discs

Blocking in excessive trash • Lower rear discs gang to drive better in soil. • Adjust angle or lift soil deflector to allow greater flow • Try reducing speed slightly

Clogging in Wet Soils 1. Raise working depth 2. Raise front discs 3. Give soil more time to dry out.

21

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

F I E L D O P E R AT I O N

ENSURE DEPTH SETTINGS ARE EVEN ACROSS THE ENTIRE WIDTH OF MACHINE BEFORE ADJUSTING FRONT & REAR DISC GANG DEPTH RELATIONSHIP. TRACKING ADJUSTMENTS

TRACKING TO THE LEFT

TRACKING TO THE RIGHT

Figure 17

Figure 16

Figure 18

REAR DISCS GANGS WORK SLIGHTLY LOWER THEN FRONT DISCS

*NB - Due to the nature of this machine, some overlap should be allowed for side tracking as soil types and conditions can vary within any given run. Where difficult trash conditions are encountered ensure rear discs are set deep enough to positively rotate in the soil.

22

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

F I E L D O P E R AT I O N

REAR VIEW OF DISC PROFILE

The disc positioning system is used for maximum soil disturbance, reduced ridging and weed control. Adjustment can also be made to compensate for disc wear. ADJUSTMENT PROCEDURE *NB - Be suremachine is tracking in line before attempting to make this adjustment. Pg 22 FRONT DISC GANG LATERAL POSITIONING • Start with factory settings. Pg 24 • To remove any ridges, test run at normal operating speed and stop quickly. • Check for ridges of undug soil. Follow ridges into machine and identify which direction to adjust - See diagrams on this page . • Only adjust front sideways in small increments ½” or 12mm • Re-check in hard soils as jump arms tend to flex more.

Figure 20

REMEMBER, FULL GROUND DISTURBANCE STARTS AT 2 ½” 60MM

Adjustable Front Gang

Left

Right

Top Elevation

Soil Throw

Figure 21

Soil Throw

(A)

(B)

(A)

Cross Sectional View Of Soil Distrubance

Move Front Gang Right To Cut Out (A) Left To Cut Out (B)

Figure 22

Figure 19

23

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

FRONT DISC GANG LATERAL POSITIONING STANDARD FACTORY SETTING

REAR

FRONT

Figure 23

Recommended Spacing - Lateral Disc Gang

22”Discs

115 mm

24”Discs

95 mm

Figure 24

Measurements may vary according to disc concavity.

24

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

F I E L D O P E R AT I O N FRONT DISC GANG LATERAL POSITIONING CONT

Slide adjuster linkage

ADJUSTMENT PROCEDURE Loosen main retaining bolts on slide mechanism • Turn slide adjusting linkage to adjust to right or left • Lock slide adjusting linkage and tighten main retaining bolts (380ft lb / 500nm tension)

Slide Bolts

Left

Right

Figure 25

Height adjustment setting

Fore & aft adjustment

SIDE COULTER ADJUSTMENT Series of holes are provided for disc height and front to back positions for optimum furrow filling.

FOR EXCESSIVE TRASH CONDITIONS • Move coulter forward and angle outwards • Raise coulter. • Move coulter to the outside of

supporting angle for more clearance.

Angle adjustment

Figure 26

25

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

M A I N T E N A N C E & S A F E P R O C E D U R E S

• Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. -Makesuremaintenanceareahasplentyofventilation. Beware exhaust fumes may cause asphyxiation. • Prior to commencing work, IDENTIFY ALL HAZARDS! Use control measures to eliminate these dangers. • Use blocks to support frame of machine on level area free of obstruction. • Always use a safety support and chock the wheels. • Never use an implement jack to support the machine. Only when doing maintenance. • Never work under raised machine unless all components are securely positioned and locked. • Engage all safety transport locks, chock wheels and front drawbar for temporary service if machine is in free standing mode. • A fire extinguisher and first aid kits should be kept readily accessible while performing maintenance on this equipment. • Follow the torque chart in this manual when tightening bolts and nuts. • Refer to bolt torque chart for head identification marking. • Always replace bolts with specified grades. • Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to original specifications, • Always use approved lifting equipment • If equipment has been altered in any way from original design, the manufacturer does not accept any liability for warranty or personal injury. • Replace all shields and guards after servicing before moving. • After servicing, be sure all tools, parts and service equipment are removed. • The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate themodel and number of your equipment to ensure prompt and efficient attention. • K-Line Agriculture spare parts and accessories

have been specifically designed and developed for themachines produced. We would call your attention to the fact that non-genuine parts and accessories are not recommended by K-Line. Use of non-genuine parts and acessories releases K-Line from all liability and makes the warranty void. The installation and/or use of non-genuine parts may, because of technical characteristics of construction, may modify or influence the performance of the machine negatively.

26

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S P E EDT I L L E R J UMP ARM AS S EMB LY

EXP L ODED V I EW

• Lift jump arm into position • Loosely attach top clamp plate ② with front clamp plate bolt ⑤ & conelock nuts ⑤. (Just start by a few threads only & leave arm hanging loosely) • Slide in torsion rubbers ③ • Loosely attach rear clamp bolts ⑤ & conelock nuts ⑤ • Check sideways positioning • Tension all clamp bolts ⑤ with conelock nuts ⑤ provided.

Figure 27

ITEM NO.

QTY

PART NO

PART

1

1

29003JAAF1.SKI

COMPLETE JUMP ARM FRONT (ALL EXCEPT DISC) COMPLETE JUMP ARM BACK (SHOWN) (ALL EXCEPT DISC) JUMP ARM ONLY FRONT (NOT INCLUDING HUB) JUMP ARM ONLY BACK (NOT INCLUDING HUB)

1

29003JAARI.SKI

1 1

29003JAWF1 29003JAWR1 29000THP08

2 3 4

1 1 1

2900 JUMP ARM TOP HAT

29000JAX230 2900 TORSION RUBBER (REQUIRES SET OF 4)

29003JAA03

COMPLETE DISC HUB UNIT

5

6 29000JABK.TH 2900 JUMP ARM BOLT KIT- 1 X M12 SET SCREW WITH CONELOCK NUT

6

5

9M12035Z8SS

M12 X 35MM BOLT

6

5

9MI2SWZ

M12 SPRING WASHER

2900 DISC BOLT KIT - 1 X PLOUGH BOLT WITH CONELOCK NUT

7

4

29000PLBK

8 8 8 8

1 1 1 1

9SD1805S 9SD2005S 9SD2206S 9SD2406S

18” X 5MM SCALLOPED DISC 20” X 5MM SCALLOPED DISC 22” X 6MM SCALLOPED DISC 24” X 6MM SCALLOPED DISC

27

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

DISC ARM BEARING

EXP L ODED V I EW

2

5

4

1

9

10

8

9

7

8

7

6

3

5

2

6

3

4

1

Figure 28

2

5

4

1

*NB Spindle torque tension 360ft lb / 500nm

ITEM NO.

QTY.

PART NUMBER

DESCRIPTION

9

1

1

29003JAW02

2900 DISC STUB

8

2

1

29003JAM02

2900 REMOVABLE 5 STUD JUMP ARM HUB

3

1

9SS508011ML

2900 JUMP ARM SEAL

7

4

1

9MRV2090

MRV2090 SEAL

6

3

5

1

9DRT40.73

DOUBLE TAPER ROLLER BEARING

6

1

29003JAM03

BEARING SPACER

7

1

29003JAM06

BEARING RETAINER

8

1

9M16040Z12CS

M16 X 40 COUNTER SUNK SCREW

9

1

9OR151

151 O-RING

10

5

9M12035Z8SS

M12 X 35MM BOLT

10

5

9M12SWZ

M12 SPRING WASHER

3, 4, 5, 8 & 9

1

29003JAKB1

BEARING KIT

28

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SIDE COULTER

EXP L ODED V I EW

Figure 29

ITEM NO.

QTY.

PART NUMBER

DESCRIPTION

WEIGHT

1

1

2900LSSWS1

2900 SPRAY STOPPER SHAFT WELDMENT

1.74

2

1

2900LSSWA1

2900 SPRAY STOPPER ANGLE

6.12

3

1

2900LSSWM1

2900 LEFT HAND SPRAY STOPPER MOUNT

8.00

4

1

29000SSWT1

2900 SPRAY STOPPER TOP HAT

3.34

5

1

29000JAX215

2900 SHORT RUBBER-220MM LONG

1.20

6

1

9HW40.62.015

LASER CUT SEAL PROTECTOR - 40.2ID X 62.2 OD X 1.5THK

0.02

7

1

Q55ISWBH

SINGLE COULTER HUB DISC MOUNT / BEARING HUB

1.01

8

1

9TC50-65-8

50OD X 65ID X 8THK OIL SEAL

0.00

9

1

9HW58.68.015

LASER CUT BEARING SPACER - 58 ID X 67.8 OD X1.5THK

0.01

10

1

9MW50M4011

ISC SEAL SPACER- 50 OD X 40 ID X 11THK

0.06

11

1

9DRT396837

DOUBLE TAPERED ROLLER BEARING

0.55

12

1

9HW18.55.08

HEAVY WASHER - 18 ID X 55 OD X 9THK

0.13

13

3

9M16SWZ

M16 SPRING WASHER, 5.5 X 4.0MM, ZINC PLATED

0.01

14

1

9M16040Z8SS

M16 X 40MM SET SCREW, ZINC PLATED, 8.8 GRADE

0.12

15

1

9CD2405

24” X 5MM PLAIN (FLAT) COULTER DISC

7.61

16

1

Q55ISHC01

Q55 SINGLE COULTER PRESSED

0.17

17

5

9M12030CHG4

M12 X 30MM CUPHEAD BOLT & NUT, GRADE 4.6, GAL

0.03

18

5

9M12SWZ

M12 SPRING WASHER, 4.0 X 2.5MM, ZINC PLATED

0.01

19

5

9M12HNG

M12 HEX NUT, GAL

0.02

20

2

9M16050Z8SS

M16 X 50MM, SET SCREW, ZINC PLATED, 8.8 GRADE

0.13

21

2

9M16FWZ

M16 FLAT WASHER, ZINC PLATED

0.01

22

2

9M16HNZ

M16 HEX NUT, ZINC PLATED

0.09

23

2

9M20045Z8SS

M20 X 45MM SET SCREW, ZINC PLATED, 8.8 GRADE

0.21

24

2

9M20SWZ

M20 SPRING WASHER, 6.0 X 4.0MM, ZINC PLATED

0.01

25

2

9M20HNZ

M20 HEX NUT, ZINC PLATED

0.07

26

6

9M12055Z8SS

M12 X 55MM SET SCREW, ZINC PLATED, GRADE 8.8

0.07

27

6

9M12CLZ

M12 CONELOCK, ZINC PLATED

0.02

29

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

50MM ROLLER BEARING SHAFT

EXP L ODED V I EW

* OP T I ON

Figure 30

ITEM NO. QTY.

PART NUMBER

DESCRIPTION

WEIGHT

1

1 1

9BHF212

F212 BEARING HOUSING

2.33 2.20 0.13 0.03 0.10

2 3 4 5 6 7

9UC2123LJ

UC212 BEARING BEARING CLIP POLY WASHER

4

9RBC01

1

9PWM04

4 9M16065Z8CS M16 X 65MM SOCKET SCREW

4

9M16CLZ

M16 CONELOCK NUT

0.04665

1

N/A

N/A

30

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

HEAVY DUTY ROLLER BEARING

EXP L ODED V I EW

* OP T I ON

Figure 31

ITEM NO.

QTY.

PART NUMBER 2900HRBM06

DESCRIPTION

1

1 1 1 1 1 1 1 1 1 1 1 1

2900H ROLLER BEARING HOUSING 22215 SPHERICAL ROLLER BEARING

2 3 4 5 6 7 8 9

9SR22215K

29000RBM05 29000RBM04 29000RBM02 29000RBM03 29000RBM01

2900H SPHERICAL SEAL LARGE BEARING SPACER 2900H INNER LABYRINTH 2900H INNER SEAL SPACER

2900H DOUBLE TAPER

9ASH2313

H2313 BEARING ADAPTOR SLEEVE

9MB13 9KM13

LOCKING WASHER

10

LOCKING NUT

11

9OR357

357 ‘O’ RING 5 1/2” X 5 7/8” X 3/16” CS COMPLETE BEARING ASSEMBLY

2900HRBA60

31

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

REAR ROLLER BEARING FITTING INSTRUCTIONS

1. Kit comes partially assembled and pre-greased. 2. IMPORTANT; Locking nut must only be tensioned with approved socket. DO NOT tighten with hammer and punch. 3. Thoroughly clean roller shaft and check for defects. 4. Run a bead of silicon along the gap in the adaptor sleeve. 5. Apply ‘Lock tight’ shaft lock to roller shaft. 6. Push bearing units onto roller shaft with mounting face to the exterior, ensuring large O-ring is installed in outer groove. Set outer mounting face of bearings apart to give a measurement of only 2-4mm less than the internal measurement of the bow, to allow easy fitting of roller assembly to bow. Distance of bearing faces must not be greater than internal measurement of bow, or O-ring may be damaged when fitting. 7. Double check bearing face position measurement is correct. 8. IMPORTANT; Bearing assembly must be fully tensioned twice for complete seating. To do this: • (a) Remove locking washer, and fully tighten castle nut to 500ft lb /700nm. • (b) Undo castle nut and insert locking washer. 9. Re-tighten locating nut to 500ft lbs /700nm. 10. Fold locking washer down. 11. Smear some grease around outer O-ring and slide roller assembly into bow, securing mounting bolts. 12. Ensure the O-ring is seated correctly, and the grease nipple is accessible. 13. Bolt flange bearing to bows and secure tightly. 14. Allow 12 hours after fitting to allow sealant to set before greasing, then follow Instructions for greasing roller bearings.

Figure 32

32

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

M E T R I C B O L T T O R Q U E TA B L E

Lubed means c l eaned dry bo l t s l ubr i cated wi th a s tandard med i um v i scos i t y mach i ne o i l . Lubr i cate a l l contac t areas of the bo l t s and washers . Lubr i cat i ng the bo l t s i s the sugges t i ng method. Thread Engagement

Figure 33

33

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

I M P E R I A L B O L T T O R Q U E TA B L E

Lubed means cleaned dry bol ts lubr icated wi th a standard medium viscosi ty machine oi l . Lubr icate al l contact areas of the bol ts and washers. Lubr icat ing the bol ts is the suggest ing method. Thread Engagement

Figure 34

34

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

S A F E T Y S I G N C A R E

• Keep safety signs clean and legible at all times • Replace safety signs that are missing or have become illegible • Replaced parts that displayed a safety sign should also display the current sign.

TO ORDER SAFETY DECALS CONTACT:

Australia: K-Line Agriculture PO Box 340 74 Young Rd Cowra NSW 2794

USA: K-Line Agriculture PO Box 567

700 Division Avenue S Cavalier ND 58220 Email: sales@k-lineag.com Free-call: 1800 445 6882

Email: sales@k-line.net.au Free-call: 1800 194 131

HOW TO INSTALL SAFETY SIGNS: • Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper. • Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. • Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. • Failure to comply could result in serious injury or death

Figure 35

Locate where necessary. (Refer to Safety decal placement, Pg36)

35

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SAFETY DECAL PLACEMENT

Figure 36

ALL model sizes have same decals & quantities.See tables below:

DECALS ON MACHINE

2940D

G

H

I

K

U

1

1

2

2

1

Figure 37

IMPORTANT If safety signs have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer or direct from factory.

36

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SAFETY DECALS

A. 9WD-W022

B. 9WD-C023

E. 9WD-D01V

G. 9WD-W021

C. 9WD-W05

D. 9WD-D04

H. 9WD-C04

I. 9WD-I01

F. 9WD-D01H

37

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SAFETY DECALS

CONT I NUED

N. 9WD-W01

J. 9WDW-T5

0. 9WD-D01

K. 9WDD-T3

R. AUS SPEED STICKER MAX 32KPH/20MPH

L. 9WD-W024

S. 9WD-W02

M. 9WD-W10

T. HYDRAULIC COLOUR

38

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SAFETY DECALS

CONT I NUED

*NOTE: WHEEL DEPTH STICKER: WHITE WITH CUT OUTS (SHOWN AS BLACK)

U. 9WD-I02

Y. WHEEL DEPTH

W. FOLDING INSTRUCTION

Q. 9WD.F01

P. 9WD-R01

39

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

T E S T I MO N I A L P E R M I S S I O N F O R M

Name: Phone Numbers: Machine Type & Size:

I give permission for K-Line to publish my: (tick all that apply)

Testimonial Name Photo Audio Video

I give permission for K-Line to give interested clients my contact number to discuss my K-Line product

SIGNATURE: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ DATE: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

My Story:

More to say? Please turn over...

40

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

Thank you!

41

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

SEND US A TESTIMONIAL EXPLAINING WHY YOU LOVE YOUR K-LINE AG PRODUCT, AND WE WILL SEND A FREE HAT! Send to marketing@k-line.net.au or scan here :

42

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

THIS PAGE IS LEFT INTENTIONALLY BLANK

43

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

WA R R A N T Y

K-LINE AGRICULTURE has been known over the last 22 years for supplying an ever expanding range of quality agricultural machinery. K-LINE AGRICULTURE warrants the products it manufactures and distributes to be free of defective materials and workmanship for a period of twelve months from date of purchase, to the first owner. Any part of the goods manufactured and distributed by K-LINE AGRICULTURE that proves to be defective material, will be replaced or repaired by K-LINE AGRICULTURE when returned to K-LINE AGRICULTURE at cost to purchaser and at purchaser’s risk. Goods sold shall only have the benefit of this warranty if the purchaser has complied with the manufacturer’s instructions in relation to the maintenance and operation of the said goods. All conditions and warranties implied by Law or Statute are hereby expressly excluded and negative so far as legally permissible. K-LINE AGRICULTURE is not otherwise liable for any direct, indirect or consequential loss or damage howsoever arising or occurring, whether founded in tort, contract, and statute or otherwise. This warranty must be read as subject to the General Terms and Conditions and does not cover misuse, neglect or negligence. ANY CLAIM FOR WARRANTY IS ALSO SUBJECT TO THE FOLLOWING CONDITIONS: • Machine has not been subject to misuse. • The speed limit of 20mph (32kmh) has been observed at all times. • The machine has not been used for custom or hire work. • Equipment must be handled, assembled, operated, maintained and stored correctly in accordance with the manufacturer’s instructions by competent personnel. • Warranty registration form must be signed by reseller and purchaser and returned to K-LINE AGRICULTURE within 14 days of invoice. Warranty is not valid unless registered. • Normal wear and tear, routine maintenance costs and accidental damage are NOT covered by this warranty. • Any alteration of equipment or negligence in maintenance including the use of non-genuine parts, renders this warranty null and void. • K-LINE AGRICULTURE will not authorize or reimburse expenses without a warranty request form filled out to K-LINE AGRICULTURE satisfaction.

Signed on behalf of K-LINE AGRICULTURE

44

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

THIS PAGE IS LEFT INTENTIONALLY BLANK

45

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

WA R R A N T Y R E G I S T R AT I O N F O R M

 Conduct comprehensive risk assessment of machine with consideration for use and maintenance

 Ensure machine is delivered as per purchase order including options

 All pins and lynch pins are in place

 Hydraulic system is primed and operating properly (if applicable).

 Check gear boxes for oil (if applicable).

 Check belts for tightness (if applicable).

 Instruction manual is supplied and explained.

It is the responsibility of the purchaser to: • Maintain in as new condition all warning and safety signs and devices at all times. • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine. • Before mounting, check with manufacturer of machine or consult engineer to ensure strength and balance of machine is adequate to accommodate the K-Line products you have purchased. • You must conduct a risk assessment, taking all risks into consideration before commissioning machine for use.

Reseller:

Client First Name: Client Last Name:

Salesman:

Trading Name:

Address:

Address:

Phone:

Phone:

Date of In- voice: Invoice No:

Email Address:

Start- Up Date:

Machine Make & Type:

Serial No:

Signed:

Signed:

To confirm registration for warranty, please return this page (signed) to F :( 02) 6342 6913 or E: sales@k-line.net.au

46

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

THIS PAGE IS LEFT INTENTIONALLY BLANK

47

2900 3PL SPEEDTILLER NON FOLDING WING

OPERATOR & SAFETY MANUAL

END OF DOCUMENT

1023 W 9th St | PO Box 248, Grafton, ND 58237 | USA 74 Young Rd | PO Box 340 ,Cowra, NSW 2794 | AUS

© K-Line Ag 2019

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45 Page 46 Page 47 Page 48

www.k-line.net.au

Made with FlippingBook - Online Brochure Maker