3400 Series ThunderRipper Operator Safety Manual

3400P SERIES FORWARD FOLD THUNDER RIPPER

OPERATOR & SAFETY MANUAL

1023 W 9th St | PO Box 248, Grafton, ND 58237 | USA 74 Young Rd | PO Box 340 ,Cowra, NSW 2794 | AUS

© K-Line Ag 2020

3445P-3460P operator & safety manual.indd 1

13/03/2020 7:37:29 AM

Wou ld you l i ke a copy of th i s manual emai l ed to you?

Send your reques t to mar ket i ng@k- l i ne . net .au or scan here :

2

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 2

13/03/2020 7:37:29 AM

Dear Customer

Thank you for purchasing a Thunder Ripper®. We would like to assure you that you have made a good choice, and will be able to rely on this high quality piece of equipment. We ask you to follow the user’s instructions closely, as this will ensure that you experience the benefits of using the machine without experiencing the unnecessary down time caused by misuse. When you receive the machine, make sure that it has not been damaged during transportation and that no parts are missing. Contact your dealer immediately if any parts are missing. Ensure that all components are correctly adjusted. The return of the Warranty Registration Form Page 39 will enable a prompt and efficient identification of your Thunder Ripper® and attention to any concern you may have. Before operating PLEASE TAKE THE TIME TO LEARN the process of operation. Do not take the unit for granted; ease into becoming familiar with your new equipment. The operator should be a responsible adult familiar with farm machinery and trained for this purpose. Do NOT allow persons to operate or assemble the unit until they have read this manual and understand how to use this machine, and observe the safety precautions. Never exceed the limits of this machine. If its ability to do a job, or to do so safely, is in question - DO NOT TRY IT.

DO NOT attempt to operate this equipment under the influence of drugs or alcohol.

Remember - Your best assurance against accidents is a careful and responsible operator.

If you have any questions not answered in this manual or require additional copies or the manual is damaged, please contact your dealer or be free to phone us on our free call number:

USA - 1800 445 6882 AUS - 1800 194 131

The team here at K-Line Agriculture trust you enjoy a good season and prove the benefits of owning and operating a quality machine that is built to perform.

Signed:

James Larsen General Manager

3

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 3

13/03/2020 7:37:29 AM

OP & SAFETY MANUAL Table Of Contents

CUSTOMER LETTER

3

EXPLODED VIEWS

27-29

SPECIFICATIONS

5

Cylinder Tine

27 28 29

Shear Pin

Pear Roller Bearing

LEGAL DISCLAIMER

5

Hydraulic Cylinder Layout

30

INTRODUCTION

6 6 6 6 6

Availability Of Genuine Parts

Bolt Torque Tables

31-32

Identifying The Machine Tractor Requirements

TESTIMONIAL PERMISSION FORM

33-34

Defintions Used In This Manual

WARRANTY Warranty Letter

37-41

37 39

RISK MANAGEMENT

7-9

Warranty Registration Form Warranty Request Form

Identifying Hazards

7 7 7 7 8 9

41

Monitor & Review Control Measures

Risk Assessment

Risk Control

Risk Assessment Score Chart

END OF DOCUMENT

45

Risk Assessment Table

SAFETY

10-24

Important Notice (MUST READ)

10

Safety Alert Symbol

11 11 11

Signal Words

Your Safety & The Safety Of Others In Important Safety Decal Placement Of Both Machines

12

Safety Decals Logo Decals Safety Sign Care

13-15

16 17 18 19 19 19

Tire Safety & Pressures

Hydraulic Operation & Safety Hydraulic Hose Hook-Up Hose Grip Colour Codes Priming Hydraulic System Hydraulic System Failure Electrical Connection Hook-Up Hooking/ Unhooking Tractor

20 21 21 22 23 24 24 25 26 26

Transporting/Roading

Folding/ Unfolding Machine

Crushing Hazard

Maintenance & Safety

Operating Instructions & Tips After Delivery Check-List

4

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 4

13/03/2020 7:37:29 AM

THUNDER RIPPER SPECIFICATIONS

MODEL SIZES

3445P

3460P

4.5M (14.8FT)

6M (19.FT)

OPERATING WIDTH APPROX.

9 (500MM) (20") 13 (350MM) (14") 4750KG (10500LB)

11 (550MM) (21.7") 13 (462MM) (18") 7000KG (15500LB)

NO.TYNES (TINE SPACING)

WEIGHT APPROX.

3.6M (11.8FT) 2.5M (8.2FT) 5.45M (17.9FT)

4.2M (13.8FT) 3.5M (11.5FT) 5.75M (18.9FT)

TRANSPORT HEIGHT APPROX. TRANSPORT WIDTH APPROX.

TRANSPORT LENGTH

315-520HP (235-390KW)

385-520HP (285-390KW)

TRACTOR POWER RANGE*

TRACTOR HYDRAULIC REQUIREMENTS

STANDARD: 3 X DOUBLE SPOOL HYDRAULIC TINES: 3 X DOUBLE SPOOL + 1 X SINGLE SPOOL

HYDRAULIC REMOTES

2800 PSI (190 BAR) (19000KPA)

HYDRAULIC PRESSURE

HYDRAULIC FLOW CAPACITY REQUIRED MAXIMUM FLOW 10GPM (38 LITRES/MIN) FLOW ADJUSTABLE *TRACTOR POWER DEPENDANT ON NUMBER OF TINES. REFER PAGE 6 FOR TRACTOR POWER REQUIREMENTS

Figure 1

LEGAL DISCLAIMER LAST UPDATED: 13/03/20

The information contained in the K-Line Industries Pty Ltd (also trading as “K-Line Ag” and “K-Line Agriculture”) manual is for general information purposes only. K-Line Industries Pty Ltd assumes no responsibility for errors or omissions in the contents of the book. In no event shall K-Line Industries Pty Ltd be liable for any special, direct, indirect, consequential, or incidental damages or any damages whatsoever, whether in an action of contract, negligence with the use of the Service or the contents of the Service. K-Line Industries Pty Ltd reserves the right to make additions, deletions, or modification to the contents of this manual at any time without prior notice.

5

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 5

13/03/2020 7:37:29 AM

AFTER DELIVERY

When you receive the machine, make sure that it has not been damaged during transportation and that no parts are missing. Only by giving us immediate notice can the necessary replacement parts be obtained. Ensure that all components are correctly adjusted.

GENUINE PARTS

K-Line spareparts and accessories havebeen specificallydesigned anddeveloped for themachines produced. We would call your attention to the fact that non-genuine parts and accessories are not recommended by K-Line. The use of such replacement parts frees K-Line from all liability and makes the warranty void. The installation and/or use of non-genuine parts may, because of technical characteristics of construction, modify or influence the performance of the machine negatively.

IDENTIFYING THE MACHINE FOR REQUESTING SPARE PARTS

The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate the model and number of your equipment to ensure prompt and efficient attention.

TRACTOR REQUIREMENTS

• 35-40 Horsepower x no. of tynes • 26-30 Kilowatt x no. of tynes • Tractor weight must be the same as or greater than the towed unit.

DEFINITIONS USED IN THIS MANUAL

Figure 2

6

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 6

13/03/2020 7:37:29 AM

R I S K M A N A G E M E N T

Risk management is the process of finding out what may cause an injury, determining what may happen as a result, and doing something about it.

The steps of risk management are: • Identify the hazards to workplace health and safety arising from work activities • Assess the risks

• Determine and implement control measures to reduce risk • Monitor and review the effectiveness of the control measures IDENTIFYING HAZARDS

Prior to commencing work, all hazards related to the work tasks should be identified. The selection of the appropriate work procedure(s) will depend on the type of work procedure(s) and hazards involved. Regular safety inspections will also identify hazards and ensure that control measures are in place. RISK ASSESSMENT Risk assessment allows appropriate control measures to be developed. Once hazards have been identified, they should be assessed in terms of their potential to do harm. To assess risk, consideration should be given to probability and consequences. (SEE RISK ASSESSMENT SCORE CHART - Pg 8). RISK CONTROL Risk control is the process of eliminating or reducing risk factors. Control measures should be chosen and implemented to eliminate or reduce risk as far as practicable. When deciding on the most appropriate measures to use, practicality and acceptance of the control measures should be considered. Safe Working Procedures should be developed for all medium-high risk hazards. MONITOR AND REVIEW CONTROL MEASURES The risk identification, assessment and control process requires regular monitoring to ensure the implemented control measures perform as originally intended and continue to prevent or adequately control the risk of injury or incident. Control measures should also be checked carefully to ensure that new hazards are not created, directly or indirectly, by the original control measures.

7

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 7

13/03/2020 7:37:29 AM

R I S K A S S E S S M E N T S C O R E C H A R T

Figure 3

AT ALL TIMES COMPLY WITH RECOMMENDATIONS AND REQUIREMENTS OF THE MANUFACTURER AND THE ENVIRONMENTAL PROTECTION AUTHORITY

8

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 8

13/03/2020 7:37:29 AM

CONT I NUED

R I S K A S S E S S M E N T

RISK SCORE

REVISED RISK SCORE

CODE

HAZARDS

CONTROL

ADJUSTING & CLEANING MUST ONLY BE DONE WHEN MACHINE IS LOWERED OR IN TRANSPORT POSITION AND ONLY AFTER ALL CHAINS AND BOLTS HAVE BEEN CHECKED FOR TIGHTNESS & WEAR IN THE LOWER POSITION. ENSURE JACK IS INSTALLED CORRECTLY & JACK RECEIVES REGULAR MAINTENANCE. KEEP FEET AND BODY CLEAR WHEN OPERATING. ENSURE NO PERSONNEL ARE BETWEEN TRACTOR & HARROW BAR WHEN HITCHING TRACTOR MACHINE MUST BE LOWERED INTO WORKING POSITION USING SUITABLE LIFTING EQUIPMENT BEFORE PRIMING IS EFFECTED BY SLIGHTLY LOOSENING FITTING/S INTO CYLINDERS AND OPERATING TRACTOR HYDRAULICS TO ACHIEVE FULL UNINTERRUPTED TRAVEL OF CYLINDER SEVERAL TIMES. THEN RE-TIGHTEN HYDRAULIC TINE FITTINGS ENSURE ALL THREE JACKS ARE CORRECTLY POSITIONED AND TAKING WEIGHT BEFORE REMOVING DRAWBAR PIN. STICKERS WARN OPERATOR MAINTAIN REGULAR CHECKS ON HYDRAULIC SYSTEM FOR WEAR & CHECK ALL FITTINGS ARE SECURE ENSURE TRACTOR OIL FLOW IS LIMITED TO REDUCE FALLING SPEED OR DO NOT INTERRUPT MACHINE FALLING UNTIL MACHINE IS FULLY IN LOWERED POSITION SAFETY PINS MUST BE PUT IN PLACE AS SOON AS MACHINE IS PUT IN TRANSPORT POSITION AND IF TRAVELLING ON PUBLIC ROADS TO DISCONNECT HYDRAULICS FROM TRACTOR

CRUSHING - WHEN ADJUSTING AND CLEANING, AS MACHINE MAY DROP WITHOUT WARNING

1

5

1(A).

CRUSHING - IMPROPER USE OF JACK

1

5

1(B).

CRUSHING - WHEN HITCHING TRACTOR

2

5

1(C).

CRUSHING - PRIOR TO PRIMING HYDRAULIC SYSTEM, AS MACHINE MAY DROP WITHOUT WARNING

1

5

1(D).

SUDDEN LIFT OF DRAWBAR CAUSING SEVERE INJURY, IF MACHINE BECOMES UNHITCHED PENETRATION OF OIL - BROKEN OR BADLY MAINTAINED HYDRAULIC LINES RUPTURE OF OIL LINES BY OVER PRESSURE WHEN MACHINE COMES TO SUDDEN STOP BEFORE FULLY LOWERING TO WORKING POSITION COLLISION - HYDRAULICS ACCIDENTALLY LOWERED WHEN MACHINE IS BEING OPERATED IN TRANSPORT

1

5

1(E).

2

5

2(A).

2

5

2(B).

1

5

3.

Figure 4

ALL HAZARDS & RISKS ARE CONTROLLED THROUGH SAFE WORKING PROCEDURES & ADEQUATE SIGNAGE

9

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 9

13/03/2020 7:37:29 AM

It is the responsibility of the operators to: Read and understand your manual. Take time to familiarize yourself with the operation of this machine, particularly the safety signs and devices fitted to this machine.

USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY.

Slow down in terrain such as rocks, or other difficult operating conditions.

I MPORTANT NOT I C E

• Safe work procedure analysis must be performed before attempting to assemble this machine.

• Do not attempt to operate this equipment under the influence of Drugs & Alcohol. • K-Line Ag can not be held responsible for any injury, death or property damage in the process of assembling this machine.

For further information please contact :

US: 1800 445 6882 AU: 1800 194 131

• Ensure Hydraulic system is fully primed, pg 20.

K-Line Ag has produced this manual as a guide for the operation of your machine. While every care and precaution has been taken in compiling this booklet, K-Line Ag carries no responsibility for errors and omissions. • This production is made available as is, without warranty of any kind expressed or implied. • K-Line Ag assumes no responsibility for damages resulting from the use of information contained herein. • This booklet is compiled to comply with the present state of the machine at the time of publication, and K-Line Ag reserves the right to improve and revise their products at any time.

10

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 10

13/03/2020 7:37:29 AM

S A F E T Y A L E R T ! ! S A F E T Y . . . Y O U C A N L I V E W I T H I T Y O U R S A F E T Y A N D T H E S A F E T Y O F O T H E R S I S I M P O R TA N T

• BE PREPARED! • BE SAFE! • BE AWARE! • BE SEEN!

When you see this symbol, you must be alert to the possibility of injury or death. SAFETY ALERT SYMBOL

SIGNAL WORDS

The use of signal words, DANGER , WARNING AND CAUTION relating to the safety messages. The appropriate signal word is selected when using the following guidelines.

Indicates an imminently hazardous situation that if not avoided, WILL result in serious injury or death if proper safety measures are not taken.

Indicates a potentially hazardous situation that, if not avoided COULD result in serious injury or death if proper safety measures are not taken .

Indicates potentially hazardous situation that, if not avoided MAY result in serious injury or death if proper safety measures are not taken.

ALL OPERATORS MUST UNDERSTAND AND ABIDE BY MAINTENANCE SAFETY PROCEDURES SET OUT IN THIS BOOK. IT IS THE RESPONSIBILITY OF THE ASSEMBLER TO ATTACH ALL SAFETY SIGNS AND DEVICES TO THIS MACHINE. FAILURE TO OBSERVE THE INSTRUCTIONS OF THIS BOOKLET COULD RESULT IN SERIOUS INJURY OR DEATH.

11

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 11

13/03/2020 7:37:29 AM

SAFETY DECAL PLACEMENT

*NOTE: Shown on 3445P model

Figure 5

Decals & quantities shown in table below:

DECALS USED ON MACHINE A B C D E G H J K L M N O R S T 1 2 1 1 2 1 1 1 1 1 6 2 1 1 2 1

Figure 6

IMPORTANT If safety signs have been damaged, removed, become illegible or parts replaced without decals, new decals must be applied. New decals are available from your authorized dealer or direct from factory.

12

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 12

13/03/2020 7:37:29 AM

S A F E T Y D E C A L S

*NOTE:

NOT ALL DECALS GO ON ALL MODELS. (See previous page for details)

A. 9WD-W022

B. 9WD-C023

E. 9WD-D01V

G. 9WD-W021

C. 9WD-W05

D. 9WD-D04

H. 9WD-C04

F. 9WD-D01H

I. 9WD-I01

13

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 13

13/03/2020 7:37:30 AM

S A F E T Y D E C A L S

CONT I NUED

N. 9WD-W01

J. 9WDW-T5

0. 9WD-D01

K. 9WDD-T3

R. AUS SPEED STICKER MAX 32KPH/20MPH

L. 9WD-W024

S. 9WD-W02

M. 9WD-W10

T. HYDRAULIC COLOR

14

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 14

13/03/2020 7:37:31 AM

S A F E T Y D E C A L S

CONTINUED

*NOTE: WHEEL DEPTH STICKER: WHITE WITH CUT OUTS (SHOWN AS BLACK)

U. 9WD-I02

Y. WHEEL DEPTH

W. FOLDING INSTRUCTION

Q. 9WD.F01

P. 9WD-R01

15

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 15

13/03/2020 7:37:33 AM

L O G O S T I C K E R S

THUNDER RIPPER STICKER: 980 X 80MM (2 x either side of drawbar) (Left side - decal cut in half)

Figure 7

K-LINE AGRICULTURE STICKER: 380 X 125MM (1 x back of center frame)

Figure 8

LEFT VIEW

Center between arrows shown in images below

BACK VIEW

Figure 9

RIGHT VIEW

Figure 11

Figure 10

16

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 16

13/03/2020 7:37:33 AM

S A F E T Y S I G N C A R E

• Keep safety signs clean and legible at all times. • Replace safety signs that are missing or have become illegible. • Replaced parts that displayed a safety sign should also display the current sign.

TO ORDER SAFETY DECALS CONTACT:

USA: K-Line Agriculture PO Box 248 1023 W 9th St Grafton ND 58237

K-Line Agriculture PO Box 340 74 Young Rd Cowra NSW 2794 Email: sales@k-line.net.au Free-call: 1800 194 131

Australia:

Email: sales@k-lineag.com Free-call: 1800 445 6882

HOW TO INSTALL SAFETY SIGNS: • Be sure that the installation area is clean and dry. • Decide on the exact position before you remove the backing paper. • Remove the smallest portion of the split backing paper. • Align the decal over the specified area and carefully press the small portion with the exposed sticky backing in place. • Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place. • Failure to comply could result in serious injury or death.

Figure 12

Locate where necessary. (Refer to safety decal placement - Pg 12)

17

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 17

13/03/2020 7:37:33 AM

TIRE SAFETY & PRESSURES ( I F WHEELS F ITTED)

SERVICING PROCEDURES

• Always cage tires before seating beads. • Never exceed stated pressures when seating beads. • Do not attempt to mount a tire unless you have the suitable equipment and experienced personnel. • Inflating tires can be dangerous. Always stand to the side when inflating. • Failure to comply could result in serious injury or death. • Load ratings of replacement tires should meet or exceed weight requirements. • Correct pressure is 90PSI/620KPA (Centre) • Before mounting wheel to machine, check all hub and rim contact surfaces are undamaged and free of paint, dirt and grease. • Lubricate wheel stubs with standard viscosity oil. • Tension wheel nuts to 350ft lbs/ 474nm. • For field operation: Re-tension after 1st, 5th, then every 50 hrs of operation. • For road travel re-tension first 3 miles (5kms), 10 miles (15kms), & thereafter at 25 miles (40kms) intervals.

Figure 13

Figure 14

Tire Pressures When Fitted With Standard 22.5 Inch Tires

TIRE PRESSURE Centre: 90PSI/620KPA

Wheel Nut Tension: 350ft lbs /474nm

Figure 15

When optional flotation tires are fitted use tire pressures stated on the tire. If no pressure stated use 50/55 PSI.

18

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 18

13/03/2020 7:37:34 AM

HYDRAUL IC OPERATION & SAFETY

HYDRAULIC HOSE HOOK UP

• For ease of hook up, hose grip handles are color coded. • The same color is used for each hydraulic circuit. • To distinguish between EXTEND and RETRACT , hose grips are marked accordingly. • Clean hydraulic hose breakaway ends before connecting to tractor. • Hose grip circuits are color coded and marked accordingly for In & Out . • After disconnecting tractor, ensure hydraulic hoses are safely stored in the hose holder.

HOSE GRIP COLOR CODES

COLOR

FUNCTION

GREEN

WING LIFT

BLUE

ROLLER (OPTION)

RED

WHEEL LIFT

EXTEND

YELLOW

FORE & AFT (TILT)

Figure 16

Figure 17 Hydraulic Ram Extension & Retraction Diagram

Out

FORE & AFT (TILT) CIRCUIT

In

WHEEL LIFT CIRCUIT

Out

In

Out

WING FOLD CIRCUIT

In

Out

ROLLER CIRCUIT

In

Figure 18

19

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 19

13/03/2020 7:37:37 AM

SAFETY

Hydraulic fluid escaping under pressure can have sufficient force to cause injury. Keep all hoses and connections in good serviceable condition. Failure to heed may result in serious personal injury or death. Escaping hydraulic fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving the pressure before disconnecting lines or performing work on the system. Make sure hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system. Use a piece of paper or cardboard, NOT BODY PARTS , to check for suspected leaks. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. DO NOT DELAY! If an accident occurs, see a doctor familiar with this type of injury immediately. Any fluid injected into the skin or eyes must be treated within a few hours or gangrene may result.

ENSURE HYDRAULIC SYSTEM IS FULLY PRIMED BEFORE USING

PRIMING HYDRAULIC SYSTEM

• Fully extend and retract hydraulic cylinders. • Repeat 3-4 times and hold lever extended each way for 10 to 15 seconds to release air from the system.

If problem exists hold hydraulic lever under pressure, until air is fully released from system.

POWER LINES CAN ARC & ELECTROCUTE WITHOUT COMING IN DIRECT CONTACT

Figure 19

Consult electricity authorities and all relevant energy companies to determine safe working distances from overhead power lines etc. BEFORE operation of this machine: • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine. • Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations.

20

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 20

13/03/2020 7:37:37 AM

SAFETY

IN THE EVENT OF HYDRAULIC SYSTEM FAILURE OR HYDRAULIC HOSE RUPTURE, YOU MUST FOLLOW THE STEPS SET OUT BELOW. Escaping Hydraulic fluid is dangerous and can cause serious injury or death.

STEP 1: PREPARE FOR SHUTDOWN. • Immediately return hydraulic lever to neutral position. • Stop operating machine.

STEP 4: APPLY THE LOCKOUT / TAG-OUT DEVICE. • Disconnect all hydraulic hoses from tractor remotes. • Place Lockout or Out of Service Tags on all hoses. STEP 5: CONTROL THE STORED ENERGY. • Ensure no hydraulic pressure remains in system, slowly release bleed tap (if equipped), or slightly loosen one hydraulic connection on each circuit to allow any remaining fluid under pressure to be released. • Double check the steps and verify that the equipment has been shut down and has the Lock and Tag Labels evident to prohibit operation. Have repairs carried out and defective parts replaced. Do not re-connect to tractor or other hydraulic power source, until system has been fully tested. STEP 6: VERIFY ISOLATION OF EQUIPMENT.

STEP 2: SHUTDOWN THE EQUIPMENT. • Use hydraulic lever to lower machine to ground (if in raised position).

STEP 3: ISOLATE THE EQUIPMENT. • Freely operate remote levers to release residual pressure from system. • If tractor is equipped place levers in float position. • Shut down tractor.

ELECTRICAL CONNECTION HOOK UP

• Ensure tractor and machine electrical connections are compatible. • Plug lead into tractor terminal. • Test lighting prior to road travel. (Power not required for field work)

21

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 21

13/03/2020 7:37:37 AM

S A F E T Y

HOOKING UP TO TRACTOR

1. Keep well clear when backing up to machine. 2. Shut down tractor. 3. Secure & lock drawbar pin in place. 4. Install safety chain by crossing the chains under the tongue and secure to the drawbar hitch frame of the tractor. 5. Clean all hydraulic couplings. 6. Hoses are coded according to function Pg 19 . 7. Beware of high pressure fluid. 8. Plug in hoses to respective remote ports. 9. Plug in electrical lead to tractor connection. 10. Release implement jack & store. 11. Check hydraulic cylinders are fully primed to avoid serious injury or death. 12. See Pg 20 to prime hydraulic system. UNHOOKING • Machine must be fully lowered or in transport position with safety locks engaged. • Use wheel chocks. • Release hydraulic pressure from system. • Lock Implement jack in place. • Remove safety chains and drawbar pin.

Figure 20

Figure 21

If implement jack is damaged DO NOT USE , replace immediately, or severe bodily harm may result.

Figure 22

22

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 22

13/03/2020 7:37:37 AM

S A F E T Y

TRANSPORTING/ROADING

1. Ensure towing unit weight is the same as or greater than the towed unit. 2. Lockout tractor drawbar swing mechanism. 3. Ensure tires are correctly inflated - Pg 18. 4. Check wheel nut tension *NB - Pg 18 for wheel nut re-tensioning times 4 sequence. 5. Ensure all safety locks are engaged. 6. Ensure safefy chains are attached to towing unit. 7. Ensure tractor brakes are latched together at all times. 8. Plan your route to avoid heavy traffic. 9. Observe bridge load ratings.

TIP OVER HAZARD this is an unbraked implement. Use extreme caution when turning and on steep terrain. Maximum towing speed is 20mph (32km/hr). DO NOT EXCEED AT ANY TIME. NEVER transport machine on public roads without complying with Federal and State laws and local regulations governing the safe movement of farm machinery. Refer to Figure 23

Figure 24

Figure 23

POWER LINES CAN ARC & ELECTROCUTE WITHOUT COMING IN DIRECT CONTACT

Figure 25

Consult electricity authorities and all relevant energy companies to determine safe working distances from overhead power lines etc. BEFORE operation of this machine. • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine. • Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations.

23

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 23

13/03/2020 7:37:38 AM

S A F E T Y

• Beware of pinch points in wing lift area when securing or releasing safety locks. • Never stand within radius of wings when in raised position, or folding and unfolding. BEWARE OF CRUSHING HAZARD WHEN ENGAGING & DISENGAGING SAFETY LOCKS & IN THE OPERATION OF THE WING FOLDING MECHANISM

Figure 26

FAILURE TO COMPLY WILL RESULT IN SERIOUS INJURY OR DEATH.

TO UNFOLD MACHINE • Fully raise with wheel lift. • Release safety locks. • Lift wings just free of lift saddle by operating tilt hydraulics (YELLOW). • Extend wing cylinders to open position (GREEN). • Lower tilt cylinders to work position (YELLOW). • TO FOLD MACHINE • Fully raise with wheel lift. • Fully raise tilt (YELLOW), and back of slightly so the wings at closing will contact saddle correctly.

Figure 27 - Safety Lock

• Fold wings into saddle (GREEN). • Lower into position (YELLOW). • Secure safety locks.

DANGER: BEWARE OF UPTHRUST AND DOWN THRUST ON DRAWBAR DURING OPERATION. Figure 28 • Tractor weight must be equal to machine weight. • Drawbar pin must be securely fastened with safety chains in place.

Figure 28

24

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 24

13/03/2020 7:37:38 AM

M A I N T E N A N C E & S A F E T Y

• Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. • Make sure maintenance area has plenty of ventilation. Beware, exhaust fumes may cause asphyxiation. • Prior to commencing work, IDENTIFY ALL HAZARDS! Use control measures to eliminate these dangers. • Use blocks to support frame of machine on level area free of obstruction. • Always use a safety support and chock the wheels. • Never use an implement jack to support the machine. Only when doing maintenance. • Never work under raised machine unless all components are securely positioned and locked. • Engage all safety transport locks, chock wheels and front drawbar for temporary service if machine is in free standing mode. • A fire extinguisher and first aid kits should be kept readily accessible while performing maintenance on this equipment. • Follow the torque chart in this manual when tightening bolts and nuts. • Refer to bolt torque chart for head identification marking. • Always replace bolts with specified grades. • Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to original specifications, • Always use approved lifting equipment • If equipment has been altered in any way from original design, the manufacturer does not accept any liability for warranty or personal injury. • Replace all shields and guards after servicing before moving. • After servicing, be sure all tools, parts and service equipment are removed. • The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate themodel and number of your equipment to ensure prompt and efficient attention.

• K-Line Agriculture spare parts and accessories have been specifically designed and developed for the machines produced. We would call your attention to the fact that non- genuine parts and accessories are not recommended by K-Line. Use of non- genuine parts and accessories releases K-Line from all liability and makes the warranty void.

The installation and/or use of non- genuine parts may, because of technical characteristics of construction, modify or influence the performance of the machine negatively.

25

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 25

13/03/2020 7:37:38 AM

OPERATING INSTRUCTIONS & TIPS

The K-Line Ag Thunder Ripper is a heavy-duty deep tillage tool designed for hard pan removal and soil fracturing. The key operating principle of the Thunder Ripper is that the roller controls the depth of the digging, and that the tilt cylinder (YELLOW) is adjusted so front & rear tines dig at same depth. • When turning on headlands lift the Thunder Ripper out of the ground. • Shear-Pin trip style tines have a break-out at approx 5000kg, hydraulic tines have a breakout at approx 1000kg at 1000PSI. • Hydraulic tines can be adjusted to 1500kg break-out at 1450PSI, however it is not recommended to operate at this pressure at all times. Increased wear will occur on components then operating at this higher pressure. • If tines are breaking out regularly, consider slowing down, reducing ripping depth, or waiting for increase in moisture content in soil (after rain).

If you have any questions please call K-Line on (02) 6340 0400.

AFTER DEL IVERY CHECK L IST

1. Check all pivot pins are fastened and anchor bolts are correctly tensioned. 2. Before mounting wheel to machine, check all hub and rim contact surfaces are undamaged and free of paint, dirt and grease.

3. Lubricate wheel studs with standard viscosity oil. 4. Tension wheel nuts to torque specifications pg 18 5. Check tires are inflated according to pressure stated on tire.

6. Check for damaged, worn and fatigued parts. Have machine repaired if necessary. 7. Ensure all appropriate safety decals are securely attached to machine – Pg 12 8. Check all safety mechanisms are in place and operating correctly. 9. Instruction manual has been stored with machine.

26

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 26

13/03/2020 7:37:38 AM

34000HTA01 BREAKDOWN

EXP L ODED V I EW

Figure 29

ITEM NO.

QTY.

PART NUMBER

DESCRIPTION

1

1

34000HTW01

3400 SERIES HYDRAULIC TYNE (HEAD) WELDMENT 1

2

1

34000HTW02

3400 SERIES HYDRAULIC TINE (PIVOT ARM) WELDMENT 2

3

1

34000HTW03

3400 SERIES HYDRAULIC TINE (TOP HAT) WELDMENT 3

DISPLACEMENT CYLINDER - 2 3/4" BORE X 150MM STROKE X 2 3/4" ROD

4

1

9CYKL28.150D

5

2

9HSB38.32.38

HARDENED STEEL BUSH - 1.5'' OD x 1.25'' ID x 1.5'' LONG

6

2

9M16025Z8SS

M16 X 25MM, SET SCREW, ZINC PLATED, 8.8 GRADE

7

2

9M16SWZ

M16 SPRING WASHER, 5.5 X 4.0MM, ZINC PLATED

8

4

9M20065Z8

M20 X 65MM, ZINC PLATED, 8.8 GRADE

9

4

9M20SWZ

M20 SPRING WASHER, 6.0 X 4.0MM, ZINC PLATED

10

4

9M20HNZ

M20 HEX NUT, ZINC PLATED

11

1

9M20FWZ

M20 X 39 X 3.0MM FLAT WASHER, ZINC PLATED

12

1

9M20NYZ

M20 NYLOC NUT, ZINC PLATED

13

1

9M24120Z8

M24 X 120MM, ZINC PLATED, GRADE 8.8

14

1

9M24150Z8

M24 X 150MM, ZINC PLATED, GRADE 8.8

15

4

9M24FWZH

M24 X 50 X 4.0MM FLAT WASHER, ZINC PLATED, STANDARD

16

2

9M24NYG

M24 NYLOC NUT, GAL

17

1

9RCPB9RC

R-CLIP 2.5MM

18

1

9TDP32.130

MACHINING OF GREASE GROOVE IN 9TDP32.130 CHROME SHAFT

19

1

9TDP32.185

TEAR DROP PIN - Ø1.25" X 185MM LONG WITH GREASE GROOVE

20

1

9TP32.190

TAPERED PIN Ø1.25'' X 190MM - M20 THREAD

21

1

9WPAG28-TP1

AG 28'' TYNE POINT 1

22

1

9WPAG28-TSG1

AG 28'' TYNE SHIN GUARD 1

23

1

9WPAG28-TSL1

AG 28'' TYNE SHANK LEG 1

27

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 27

13/03/2020 7:37:38 AM

SHEAR-PIN TRIP TINE

EXP L ODED V I EW

*NOTE: • ENTIRE TINE ASSEMBLY : 9WPAG7014-020.6 • 9WPTIAPAG016 COMES WITH THE 2 X RCPB11HP & THE 1 X PIN

• 9WPAG28-MBA.6 CAN BE ORDERED AS A WHOLE UNIT OR FIXING HARDWARE CAN BE SUPPLIED WITHOUT CP1 & CP2

Figure 30

BOM ID

PART NUMBER

DESCRIPTION

QTY PER TYNE

TOTAL QTY 3435D

TOTAL QTY 3460D

1

9M24090Z8

M24 X 90MM, ZINC PLATED, GRADE 8.8

4

28

44

2

9WPAG28-MBA.6.CP2 AG 28’’ TYNE - 6’’ MOUNT - CLAMP PIECE 2

1

7

11

3

9WPAG28-MBA.6.CP1 AG 28’’ TYNE - 6’’ MOUNT - CLAMP PIECE 1

1

7

11

4

9M24SWZ

M24 SPRING WASHER, 7.0 X 5.0MM, ZINC PLATED

8

56

88

5

9M24HNZ

M24 HEX NUT, ZINC PLATED

4

28

44

6

9I22089Z8

7/8 X 3.5” BOLT, UNC, GRADE 8, ZINC PLATED

1

7

11

7

9I022SWZ

7/8” SPRING WASHER, 1/4 X 3/16”, ZINC PLATED

1

7

11

8

9I022HNZ

7/8” HEX NUT, UNC, STEEL, ZINC PLATED

1

7

11

9

9WPTIAPAG016

SHEAR PIN FOR 9WPAG7014-020

1

7

11

10 9RCPB11HP

HAIR PIN CLIP - 3MM WIRE, SUITS 1” DIAMETER PINS

2

14

22

11

9WPAG28-TSL1

AG 28'' TYNE SHANK LEG 1

1

7

11

12

9WPAG28-TSG1

AG 28’’ TYNE SHIN GUARD 1

1

7

11

13

9RCPB9RC

R-CLIP 2.5MM

1

7

11

14

9WPAG28-TP1

AG 28’’ TYNE POINT 1

1

7

11

28

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 28

13/03/2020 7:37:38 AM

PEER ROLLER BEARING

EXP L ODED V I EW

* X 4 BEARINGS REQUIRED EACH MACHINE (2 X BEARINGS PER ROLLER)

Figure 31

ITEM NO.

QTY.

PART NUMBER 9BUC60F212P6L

DESCRIPTION

1

1

PEER 60MM BEARING IN F212 HOUSING

29

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 29

13/03/2020 7:37:38 AM

HYDRAUL I C CY L I NDE R L AYOUT

Figure 32

ITEM NO.

QTY.

PART NUMBER

DESCRIPTION

CYLINDER 5.5” X 48” X 2.5” ROD, WITH SF60ES BALL END ON BUTT END, M64 X 3 THREADED ROD CYLINDER HD 60MM ROD END BALL END (SIA60ES) WITH M64 THREAD PHASED CYLINDER 4.5" X 8" X 2"ROD, 1.3/4" UNF THREAD COMES WITH M64 ADAPTOR AND SF60ES ON BUTT END PHASED CYLINDER 5" X 8" X 55M,M ROD 1.3/4" UNF THREAD COMES WITH M64 ADAPTOR AND SF60ES ON BUTT END CYLINDER 5” X 24” X 2” ROD, WITH GK60DO BALL END ON BUTT END, M42 X 2 THREADED ROD

1

1

9CYKL55.48

2

1

9BESIA60ES

3

1

9CYKL45.8PH01

4

1

9CYKL5.8PH01

4

2

9CYKL5.24

5

2

9BESIGEW50ES

50MM ID SIGEW SERIES SCREW-ON ROD END BALL END

DISPLACEMENT CYLINDER - 2 3/4" BORE X 150MM STROKE X 2 3/4" ROD

9CYKL28.150D

30

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 30

13/03/2020 7:37:38 AM

M E T R I C B O L T T O R Q U E TA B L E

Lubed means c l eaned dry bo l t s l ubr i cated wi th a s tandard med i um v i scos i t y mach i ne o i l . Lubr i cate a l l contac t areas of the bo l t s and washers . Lubr i cat i ng the bo l t s i s the sugges ted method. Thread Engagement

Figure 33

31

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 31

13/03/2020 7:37:38 AM

I M P E R I A L B O L T T O R Q U E TA B L E

Lubed means cleaned dry bolts lubricated with a standard medium viscosity machine oil. Lubricate all contact areas of the bolts and washers. Lubricating the bolts is the suggested method. Thread Engagement

Figure 34

32

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 32

13/03/2020 7:37:39 AM

T E S T I MO N I A L P E R M I S S I O N F O R M

Name: Phone Numbers: Machine Type & Size:

I give permission for K-Line to publish my: (tick all that apply)

Testimonial Name Photo Audio Video

I give permission for K-Line to give interested clients my contact number to discuss my K-Line product

SIGNATURE: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ DATE: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

My Story:

More to say? Please turn over...

33

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 33

13/03/2020 7:37:39 AM

Thank you!

34

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 34

13/03/2020 7:37:39 AM

SEND US A TESTIMONIAL EXPLAINING WHY YOU LOVE YOUR K-LINE AG PRODUCT, AND WE WILL SEND A FREE HAT! Send to marketing@k-line.net.au or scan here :

35

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 35

13/03/2020 7:37:39 AM

THIS PAGE IS LEFT INTENTIONALLY BLANK

36

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 36

13/03/2020 7:37:39 AM

WA R R A N T Y

K-LINE AGRICULTURE has been known over the last 22 years for supplying an ever expanding range of quality agricultural machinery. K-LINE AGRICULTURE warrants the products it manufactures and distributes to be free of defective materials and workmanship for a period of twelve months from date of purchase, to the first owner. Any part of the goods manufactured and distributed by K-LINE AGRICULTURE that proves to be defective material, will be replaced or repaired by K-LINE AGRICULTURE when returned to K-LINE AGRICULTURE at cost to purchaser and at purchaser’s risk. Goods soldshall onlyhave thebenefit of thiswarranty if thepurchaser has compliedwith themanufacturer’s instructions in relation to the maintenance and operation of the said goods. All conditions and warranties implied by Law or Statute are hereby expressly excluded and negative so far as legally permissible. K-LINE AGRICULTURE is not otherwise liable for any direct, indirect or consequential loss or damage howsoever arising or occurring, whether founded in tort, contract, and statute or otherwise. This warranty must be read as subject to the General Terms and Conditions and does not cover misuse, neglect or negligence. ANY CLAIM FOR WARRANTY IS ALSO SUBJECT TO THE FOLLOWING CONDITIONS: • Machine has not been subject to misuse. • The speed limit of 20mph (32kmh) has been observed at all times. • The machine has not been used for custom or hire work. • Equipment must be handled, assembled, operated, maintained and stored correctly in accordance with the manufacturer’s instructions by competent personnel. • Warranty registration form must be signed by reseller and purchaser and returned to K-LINE AGRICULTURE within 14 days of invoice. Warranty is not valid unless registered. • Normal wear and tear, routine maintenance costs and accidental damage are NOT covered by this warranty. • Any alteration of equipment or negligence in maintenance including the use of non-genuine parts, renders this warranty null and void. • K-LINE AGRICULTURE will not authorize or reimburse expenses without a warranty request form filled out to K-LINE AGRICULTURE satisfaction.

Signed on behalf of K-LINE AGRICULTURE

37

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 37

13/03/2020 7:37:39 AM

THIS PAGE IS LEFT INTENTIONALLY BLANK

38

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 38

13/03/2020 7:37:39 AM

WA R R A N T Y R E G I S T R AT I O N F O R M

 Conduct comprehensive risk assessment of machine with consideration for use and maintenance

 Ensure machine is delivered as per purchase order including options

 All pins and lynch pins are in place

 Hydraulic system is primed and operating properly (if applicable).

 Check gear boxes for oil (if applicable).

 Check belts for tightness (if applicable).

 Instruction manual is supplied and explained.

It is the responsibility of the purchaser to: • Maintain in as new condition all warning and safety signs and devices at all times. • Ensure all operators are familiar with this manual and all safety devices and features of the machine. • Maintain the machine at all times in a condition that is safe to operate, and ensure it complies with any relevant safety acts of parliament, government authorities and regulations. • Take every reasonable precaution as is commonly expected in this industry and in the operation of the machine. • Before mounting, check with manufacturer of machine or consult engineer to ensure strength and balance of machine is adequate to accommodate the K-Line products you have purchased. • You must conduct a risk assessment, taking all risks into consideration before commissioning machine for use.

Reseller:

Client First Name: Client Last Name:

Salesman:

Trading Name:

Address:

Address:

Phone:

Phone:

Date of In- voice: Invoice No:

Email Address:

Start- Up Date:

Machine Make & Type:

Serial No:

Signed:

Signed:

To confirm registration for warranty, please return this page (signed) to F :( 02) 6342 6913 or E: sales@k-line.net.au

39

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 39

13/03/2020 7:37:39 AM

THIS PAGE IS LEFT INTENTIONALLY BLANK

40

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 40

13/03/2020 7:37:39 AM

WA R R A N T Y R E Q U E S T F O R M

RESELLER: _______________________CLIENT: ______________________ ADDRESS: _______________________ _____________________________ PHONE: ______________________________________________________ MACHINE MAKE & TYPE: ____________________________________________ SERIAL NO: ______________________ CUSTOMER ORDER NO: _______ INVOICE NO: _____________________ DATE OF INVOICE: ___________ FULL DESCRIPTION: ________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ CAUSE: ____________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ DATE OF FAILURE: _______________ HOURS WORKED: _____________ DATE OF REPAIR: ________________ HECTARES WORKED: __________ I AGREE: 1. That in accordance with the warranty given by K-LINE AGRICULTURE, I have taken every reasonable precaution as is commonly expected in this industry in the operation of the machine.

2. This claim is not due to negligence, lack of maintenance, routine wear & tear or accidental damage & no unauthorized alteration has been made to this machine.

OPERATOR: SIGNATURE ________________________________ DATE:_____________________

OWNER: SIGNATURE

_________________________________

DATE:_____________________

OFFICE USE ONLY: ACCEPTED: YES/NO

DENIED:

YES/NO

DATE: ___________________________________ GOODS REPAIRED/ REPLACED/ REFUNDED FOR

DATE: _____________________________ REASON FOR DENIAL: _______________

CREDIT? (CIRCLE)

___________________________________

REFUND OR REIMBURSEMENT REQUIRED? _ CHQ NO/ ADJUSTMENT NOTE NO: ___________ SHIPPING DETAILS: _______________________ APPROVED BY: ___________________________

__________________________________

CHANGE REQUIRED? (CIRCLE)

DESIGN

WORK METHOD

ACTION TAKEN: ___________________________ SUPPLIED PRODUCT __________________________________________ REFER TO SUPPLIER CLIENT SATISFIED YES/NO RECALL REQUIRED FILE CLOSED BY: _________________________

DATE: _____________________________

41

3400P SERIES FORWARD FOLD THUNDER RIPPER Ⓡ

OPERATOR & SAFETY MANUAL

3445P-3460P operator & safety manual.indd 41

13/03/2020 7:37:39 AM

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44 Page 45

www.k-line.net.au

Made with FlippingBook - Online Brochure Maker