Milling Solid Carbide End Mills
Solid Carbide End Mill M200 Cutting Data Recommendation
1.0D
0.5D
M200-2ES Slot milling
Slot milling ( ISO M)
Materials
( ISO P/K)
1.0D
1.0D
fz [mm/Tooth] Mill diameter [mm] 2 4 6 8 1012141620
Cutting speed Vc(m/min)
ISO
Workpiece Materials
C ≤ 0.25%
Annealed 125 428
85-120 0.007 0.018 0.027 0.045 0.054 0.059 0.063 0.072 0.099
0.25 < C ≤ 0.55%
Annealed 190 639
95-130 0.008 0.020 0.030 0.050 0.060 0.065 0.070 0.080 0.110
0.25 < C ≤ 0.55%
Heat-treated 210 708
95-130 0.008 0.020 0.030 0.050 0.060 0.065 0.070 0.080 0.100
Unalloyed steel
Annealed 190 639
95-130 0.008 0.019 0.029 0.048 0.057 0.062 0.067 0.076 0.105
C > 0.55%
Heat-treated 300 1013
75-100 0.007 0.018 0.027 0.045 0.054 0.059 0.063 0.072 0.099
C > 0.55%
Free cutting steel
Annealed 220 745
80-120 0.008 0.019 0.029 0.048 0.057 0.062 0.067 0.076 0.105
Annealed
175 591
100-120 0.008 0.019 0.029 0.048 0.057 0.062 0.067 0.076 0.105
Heat-treated
300 1013
60-100 0.007 0.018 0.027 0.045 0.054 0.059 0.063 0.072 0.099
Low-alloyed steel
Heat-treated
380 1282
60-100 0.007 0.017 0.026 0.043 0.052 0.056 0.060 0.069 0.095
Heat-treated
430 1477
50-75 0.007 0.016 0.025 0.041 0.049 0.053 0.057 0.066 0.090
Annealed
200 675
90-120 0.007 0.018 0.027 0.045 0.054 0.059 0.063 0.072 0.099
High-alloyed steel and highalloyed tool steel
Hardened and tempered
300 1013
75-100 0.007 0.018 0.027 0.045 0.054 0.059 0.063 0.072 0.099
Hardened and tempered
400 1361
50-80 0.007 0.017 0.026 0.043 0.052 0.056 0.060 0.069 0.095
Ferritic/Martensite,Annealed
200 675
40-70 0.006 0.015 0.023 0.038 0.045 0.049 0.053 0.060 0.083
Stainless steels
Martensite,Heat-treated
330 1114
40-50 0.005 0.013 0.020 0.033 0.039 0.042 0.046 0.052 0.072
Austenitic,hardened
200 675
50-70 0.006 0.020 0.035 0.043 0.050 0.055 0.060 0.067 0.080
Stainless steels
Austenitic,precipitation hardened stainless steel(PH stainless steel)
300 1013
30-50 0.005 0.016 0.028 0.034 0.040 0.044 0.048 0.054 0.064
Austenitic,ferritic,duplex
230 778
40-50 0.006 0.019 0.033 0.041 0.048 0.052 0.057 0.064 0.076
Ferritic
200 400
110-145 0.012 0.020 0.042 0.060 0.075 0.085 0.100 0.110 0.125
Malleable cast iron
Pearlitic
260 700
90-120 0.010 0.017 0.036 0.051 0.064 0.072 0.085 0.094 0.106
Low tensile strength
180 200
120-130 0.012 0.020 0.042 0.060 0.075 0.085 0.100 0.110 0.125
Grey cast iron
High tensile strength/Austenitic
245 350
100-120 0.011 0.018 0.038 0.054 0.068 0.077 0.090 0.099 0.113
Ferritic
155 400
100-120 0.012 0.020 0.042 0.060 0.075 0.085 0.100 0.110 0.125
Nodular cast iron
Pearlitic
265 700
85-115 0.010 0.017 0.036 0.051 0.064 0.072 0.085 0.094 0.106
GGV(CGI) Wrought aluminum alloy Cast aluminum alloy
230 400
60-95 0.010 0.016 0.034 0.048 0.060 0.068 0.080 0.088 0.100
Non-aging alloy
30
-
Aged alloy
100 340
≤ 12% Si, non-aging alloy
75
260
≤ 12% Si, aged alloy
90
310
＞ 12% Si, non-aging alloy
130 450
Magnesium alloy
70
250
Unalloyed,electrolytic copper
100 340
Copper and copper alloy(bronze/ brass)
Brass,bronze,red brass
90
310
Cu alloy,short chip
110 380
High tensile,Ampco alloy
300 1010
Annealed 200 680 Aged 280 940 Annealed 250 840 Aged 350 1180 Cast 320 1080
Fe-based
Fe-based alloy
Ni or Co based
Pure Titanium
200 680
Titanium alloy
α and β alloy, aged
375 1260
β alloy
410 1400
Tungsten alloy
300 1010
Molybdenum alloy
300 1010
Hardened and tempered
50HRC -
Hardened steel
Hardened and tempered
55HRC -
Hardened and tempered
60HRC -
Chilledcastiron Hardened and tempered
55HRC -
The cutting data are average recommended values. For special applications, adjustment is needed.
458
Made with FlippingBook - Online Brochure Maker