Milling Solid Carbide End Mills
Solid Carbide End Mill M210 Cutting Data Recommendation
1.0D
0.3-0.5D
M210-4CS Slot milling M210-4RS ( ISO P/K)
Slot milling ( ISO M/S)
Materials
1.0D
1.0D
fz [mm/Tooth] Mill diameter [mm] 4 6 8 101214161820
Cutting speed Vc(m/min)
ISO
Workpiece Materials
C ≤ 0.25%
Annealed 125 428
85-150 0.016 0.023 0.032 0.040 0.054 0.059 0.063 0.072 0.081
0.25 < C ≤ 0.55%
Annealed 190 639
110-150 0.018 0.025 0.035 0.044 0.060 0.065 0.070 0.080 0.090
0.25 < C ≤ 0.55%
Heat-treated 210 708
110-150 0.018 0.025 0.035 0.044 0.060 0.065 0.070 0.080 0.090
Unalloyed steel
Annealed 190 639
100-120 0.017 0.024 0.033 0.042 0.057 0.062 0.067 0.076 0.086
C > 0.55%
Heat-treated 300 1013
80-110 0.016 0.023 0.032 0.040 0.054 0.059 0.063 0.072 0.081
C > 0.55%
Free cutting steel
Annealed 220 745
100-120 0.017 0.024 0.033 0.042 0.057 0.062 0.067 0.076 0.086
Annealed
175 591
100-120 0.017 0.024 0.033 0.042 0.057 0.062 0.067 0.076 0.086
Heat-treated
300 1013
80-110 0.016 0.023 0.032 0.040 0.054 0.059 0.063 0.072 0.081
Low-alloyed steel
Heat-treated
380 1282
80-100 0.015 0.022 0.030 0.038 0.052 0.056 0.060 0.069 0.077
Heat-treated
430 1477
70-110 0.015 0.021 0.029 0.036 0.049 0.053 0.057 0.066 0.074
Annealed
200 675
100-120 0.016 0.023 0.032 0.040 0.054 0.059 0.063 0.072 0.081
High-alloyed steel and highalloyed tool steel
Hardened and tempered
300 1013
80-100 0.016 0.023 0.032 0.040 0.054 0.059 0.063 0.072 0.081
Hardened and tempered
400 1361
70-110 0.015 0.022 0.030 0.038 0.052 0.056 0.060 0.069 0.077
Ferritic/Martensite,Annealed
200 675
50-70 0.014 0.019 0.026 0.033 0.045 0.049 0.053 0.060 0.068
Stainless steels
Martensite,Heat-treated
330 1114
40-60 0.012 0.016 0.023 0.029 0.039 0.042 0.046 0.052 0.059
Austenitic,hardened
200 675
60-80 0.017 0.025 0.035 0.040 0.045 0.050 0.060 0.070 0.080
Stainless steels
Austenitic,precipitation hardened stainless steel(PH stainless steel)
300 1013
30-45 0.014 0.020 0.028 0.032 0.036 0.040 0.048 0.056 0.064
Austenitic,ferritic,duplex
230 778
40-50 0.016 0.024 0.033 0.038 0.043 0.048 0.057 0.067 0.076
Ferritic
200 400
100-130 0.020 0.035 0.050 0.070 0.080 0.090 0.090 0.100 0.110
Malleable cast iron
Pearlitic
260 700
90-120 0.017 0.030 0.043 0.060 0.068 0.077 0.077 0.085 0.094
Low tensile strength
180 200
120-130 0.020 0.035 0.050 0.070 0.080 0.090 0.090 0.100 0.110
Grey cast iron
High tensile strength/Austenitic
245 350
95-110 0.018 0.032 0.045 0.063 0.072 0.081 0.081 0.090 0.099
Ferritic
155 400
110-130 0.020 0.035 0.050 0.070 0.080 0.090 0.090 0.100 0.110
Nodular cast iron
Pearlitic
265 700
85-110 0.017 0.030 0.043 0.060 0.068 0.077 0.077 0.085 0.094
GGV(CGI) Wrought aluminum alloy Cast aluminum alloy
230 400
95-110 0.016 0.028 0.040 0.056 0.064 0.072 0.072 0.080 0.088
Non-aging alloy
30
-
Aged alloy
100 340
≤ 12% Si, non-aging alloy
75
260
≤ 12% Si, aged alloy
90
310
＞ 12% Si, non-aging alloy
130 450
Magnesium alloy
70
250
Unalloyed,electrolytic copper
100 340
Copper and copper alloy(bronze/ brass)
Brass,bronze,red brass
90
310
Cu alloy,short chip
110 380
High tensile,Ampco alloy
300 1010
Annealed 200 680
40-55 0.011 0.019 0.025 0.035 0.045 0.060 0.070 0.070 0.080
Fe-based
Aged 280 940
30-40 0.009 0.015 0.020 0.028 0.036 0.048 0.056 0.056 0.064
Fe-based alloy
Annealed 250 840
40-55 0.011 0.019 0.025 0.035 0.045 0.060 0.070 0.070 0.080
Ni or Co based
Aged 350 1180
30-40 0.009 0.015 0.020 0.028 0.036 0.048 0.056 0.056 0.064
Cast
320 1080
30-40 0.009 0.015 0.020 0.028 0.036 0.048 0.056 0.056 0.064
Pure Titanium
200 680
40-55 0.012 0.021 0.028 0.039 0.050 0.066 0.077 0.077 0.088
Titanium alloy
α and β alloy, aged
375 1260
40-55 0.012 0.021 0.028 0.039 0.050 0.066 0.077 0.077 0.088
β alloy
410 1400
30-40 0.008 0.014 0.019 0.026 0.034 0.045 0.053 0.053 0.060
Tungsten alloy
300 1010
50-60 0.013 0.023 0.030 0.042 0.054 0.072 0.084 0.084 0.096
Molybdenum alloy
300 1010
50-60 0.013 0.023 0.030 0.042 0.054 0.072 0.084 0.084 0.096
Hardened and tempered
50HRC -
Hardened steel
Hardened and tempered
55HRC -
Hardened and tempered
60HRC -
Chilledcastiron Hardened and tempered
55HRC -
The cutting data are average recommended values. For special applications, adjustment is needed.
463
Made with FlippingBook - Online Brochure Maker