MOVING COIL CARTRIDGES SPECIFICATION FOR MONO VINTAGE RECORDS
for 78 rpm Shellac SP Records
for Mono Vinyl AT-MONO3/LP
for Mono Vinyl AT33 MONO
AT-MONO3/SP
Model Number
Type
Horizontal Mono Moving Coil (see note n°6)
Horizontal Mono Moving Coil (see note n°6)
Horizontal Mono Moving Coil Aluminium/Synthetic Resin
Body Material
Aluminium/Synthetic Resin
Aluminium/Synthetic Resin
Frequency Response
20 to 15,000 Hz
20 to 20,000 Hz
20 to 20,000 Hz
Output Voltage
1.2 mV (at 1 kHz,12 cm/sec)
1.2 mV (at 1 kHz, 5.0 cm/sec)
0.35 mV (at 1 kHz, 5.0 cm/sec) 23 degrees (see note n°1) 2.3 to 2.7 g (standard 2.5 g
Vertical Tracking Angle
23 degrees
23 degrees
Vertical Tracking Force Range
3 to 7 g (standard 5.0 g)
1.5 to 2.5 g (standard 2.0 g)
Stylus Shape
Conical
Conical
Conical
Stylus Curvature Radius Stylus Construction & Size
2.5 mil (see note n°5) Bonded round shank Aluminium Pipe 10 x 10 – 6 cm / dyne
0.6 mil (see note n°5) Bonded round shank
0.65 mil (see note n°5) Nude square shank
Cantilever
Aluminium Pipe
Duralumin Pipe
Static Compliance Dynamic Compliance Wire Used for Coil
20 x 10 – 6 cm / dyne
20 x 10 – 6 cm / dyne
3.5 x 10 – 6 cm / dyne (100 Hz)
7 x 10 – 6 cm / dyne (100 Hz)
6 x 10 – 6 cm / dyne (100 Hz)
PCOCC (see note n°3)
PCOCC (see note n°3)
PCOCC (see note n°3) Min 100 W (see note n°7)
Recommended Load Impedance
400 W to 47,000 W (see note n°7)
400 W to 47,000 W (see note n°7)
Coil Impedance DC Resistance Coil Inductance Cartridge Weight
40 W (1 kHz)
40 W (1 kHz)
10 W (1 kHz)
40 W
40 W
10 W
190 m H (1 kHz)
190 m H (1 kHz)
28 m H (1 kHz)
6.8 g
6.8 g
6.9 g
Dimensions Mounting
16.0 (H) x 16.6 (W) x 26.5 (L) mm
16.0 (H) x 16.6 (W) x 26.5 (L) mm
16.0 (H) x 16.6 (W) x 26.5 (L) mm
1/2” centres
1/2” centres
1/2” centres
Accessories Included
Non-magnetic screw driver; 1 brush; 2 washers; 2 x 20 mm mounting screws; 2 x 13 mm mounting screws; 2 x nuts; 1 plastic protector; 1 set of PCOCC lead wires AT6101
Non-magnetic screw driver; 1 brush; 2 washers; 2 x 20 mm mounting screws; 2 x 13 mm mounting screws; 2 x nuts; 1 plastic protector; 1 set of PCOCC lead wires AT6101
Non-magnetic screw driver; 1 brush; 2 washers; 2 x 19 mm mounting screws; 2 x 13 mm mounting screws; 1 plastic protector; 2 x nuts; 1 set of PCOCC lead wires AT6101
XP SERIES AUDIOPHILE DJ MOVING MAGNET CARTRIDGES SPECIFICATIONS
AT-XP7
AT-XP5
AT-XP3
Model Number
Type
Moving Magnet VM Cartridge
Moving Magnet VM Cartridge
Moving Magnet VM Cartridge
Mounting
Half-inch
Half-inch
Half-inch
Frequency Response Channel Separation Output Channel Balance
20 to 20,000 Hz 22 dB (1 kHz) 2.0 dB (1 kHz)
20 to 18,000 Hz 20 dB (1 kHz) 2.0 dB (1 kHz)
20 to 18,000 Hz 20 dB (1 kHz) 2.0 dB (1 kHz)
Output Voltage
6.0 mV (at 1 kHz, 5 cm/sec) 20 degree (see note n°1) 2.0 to 4.0 g (standard 3g)
5.5 mV (at 1 kHz, 5 cm/sec) 20 degree (see note n°1) 2.0 to 4.0 g (standard 3g)
5.5 mV (at 1 kHz, 5 cm/sec) 20 degree (see note n°1) 2.0 to 4.0 g (standard 3g)
Vertical Tracking Angle
Vertical Tracking Force Range
Stylus Shape Stylus Size
Elliptical bonded
Elliptical bonded
Conical bonded 0.6 mil (see note n°5)
0.3 x 0.7 mil (see note n°5) Bonded Round Shank Aluminium tapered tube
0.3 x 0.7 mil (see note n°5) Bonded Round Shank Carbon reinforced ABS
Stylus Construction
Bonded Round Shank Carbon reinforced ABS
Cantilever
Coil Impedance Static Compliance Dynamic Compliance
6,700 W (1 kHz)
6,700 W (1 kHz)
6,700 W (1 kHz)
20 x 10 – 6 cm / dyne
20 x 10 – 6 cm /dyne
20 x 10 – 6 cm /dyne
8.0 x 10 – 6 cm / dyne (100 Hz)
6.0 x 10 – 6 cm / dyne (100 Hz)
6.0 x 10 – 6 cm / dyne (100 Hz)
Recommended Load Impedance Recommended Load Capacitance
47,000 W
47,000 W
47,000 W
100-200 pF
100-200 pF
100-200 pF
Weight
6.2g
6.2g
6.2g
Dimensions
17.2 (H) x 17.8 (W) x 28.3 (L) mm
17.2 (H) x 17.8 (W) x 28.3 (L) mm
17.2 (H) x 17.8 (W) x 28.3 (L) mm
Replacement Stylus Accessories Included
ATN-XP7
ATN-XP5
ATN-XP3
Cartridge installation screws 11 mm x 2,8 mm x 2; Washer x 2; Nut x 2; Non-magnetic screwdriver x 1
Cartridge installation screws 11 mm x 2,8 mm x 2; Washer x 2; Nut x 2; Non-magnetic screwdriver x 1
Cartridge installation screws 11 mm x 2,8 mm x 2; Washer x 2; Nut x 2; Non-magnetic screwdriver x 1
XP SERIES PRE-MOUNTED CARTRIDGE-HEADSHELL SETS SPECIFICATIONS
AT-XP7/H
AT-XP5/H
AT-XP3/H
Model Number
Dimensions
H21.2×W21.4×L62.4mm
H21.2×W21.4×L62.4mm
H21.2×W21.4×L62.4mm
Weight
15.6g
15.6g
15.6g
(1) Vertical tracking angle of 20 degrees is IEC/DIN standard. (2) When the stylus is to be replaced, replace the entire cartridge. Take the used cartridge to your Audio‑Technica Authorized Service Centre. The new cartridge, or any other model which is desired among the line-up of MC cartridges sold by Audio‑Technica, are available at the stylus replacement price (contact an Audio‑Technica Authorized Service Centre). (3) PCOCC = Pure Copper by Ohno Continuous Casting process. (4) When head amplifier connected. (5) The abbreviation mil is equal a thousandth of an inch - mil = 0,001 inch = 0,0254 mm = 25,4 m m
(6) Due to high output voltage this moving coil cartridge can be used directly in MM phono inputs without the use of a step-up transformer. (7) When connected to the MC input of a transformer-less phono pre-amp, choose a lower gain position due to the high output voltage (1.2 mV).
Audio-Technica Phono Cartridges Guide 2025 - 49
Made with FlippingBook - professional solution for displaying marketing and sales documents online