PRINCE™ PTO Gear Pumps
• Aluminum or Cast Iron center housing with cast iron end plates • Two outlet ports with plug to seal unused port • Self adjusting wear plates **Drive Shaft Required**
• SAE Ports • Oil Temp to 180F • Fixed displacement
CYLINDERS
Inlet Port (suction) is the larger port - stamped arrow designates the direction of the shaft and flow of oil. CID = Cubic Inch Displacement - the amount of oil that is discharged in one revolution of the gears Flow Rate (gpm) = Displacement (CID) X Speed (rpm) / 231
CYLINDER COMPONENTS
PART NO.
INLET PORT
OUTLET PORT
PRINCE NO.
HP CID GPM RPM PSI
DRIVING SHAFT REQ
Aluminum Center Housing - 6 Tooth Spline x 1 3/8” Diameter**
251563 251555 251560
HC-PTO-2A 18.1 5.70 11.40 540 HC-PTO-9A 27.4 7.80 17.10 540 HC-PTO-1A 32.1 9.90 21.00 540
2250 2250 2250
SAE 16 SAE 16 SAE 16
SAE 12 SAE 12 SAE 12
1 3/8 dia. 6 tooth spline 1 3/8 dia. 6 tooth spline 1 3/8 dia. 6 tooth spline
JACKS
Aluminum Center Housing - 21 Tooth Spline x 1 3/8” Diameter**
251565 251566
HC-PTO-3A 34.3 5.70 22.40
1000 2250 1000 2250
SAE 16
SAE 12 SAE 16
1 3/8 dia. 21 tooth spline 1 3/8 dia. 21 tooth spline
VALVES
HC-P-K11
58.8 9.90 40.00
SAE 20 rear
Cast Iron Housing - 6 Tooth Spline x 1 3/8” Diameter**
251557 251562
HC-PTO-2AC 18.1 5.70 11.40 540 HC-PTO-1AC 32.1 9.90 21.00 540
2250 2250
SAE 16 SAE 16
SAE 12 SAE 12
1 3/8 dia. 6 tooth spline 1 3/8 dia. 6 tooth spline
MOTORS
Cast Iron Housing - 21 Tooth Spline x 1 3/8” Diameter**
251554 205116 205220
HC-P-K11C 32.1 9.90 21.00
1000 2250
SAE 20 rear
SAE 16
1 3/8 dia. 21 tooth spline
PMCK-PTO-1A 180900877
Seal Kit for both aluminum & cast iron
Torque Arm Kit
PUMPS
VANE & DUMP PUMPS
ENGINES
FLUIDYNE™ - V10 & V20 Vane Pumps
• Direct replacement for Vickers vane pumps • 3/4” straight keyed shaft • Flip cam ring to change the rotation of the pump - note, this will void the warranty.
POWER UNITS
INLET PORT
OUTLET PORT
PART NO.
ROTATION
CID
GPM
RPM
PSI
MOUNTING
FILTRATION
V10 Vane Pumps
250128 250125 250124 256132 256107 250134 256148 250133
CW CW CW CW
0.60 0.80 1.00 1.19 1.62 1.62 1.81 2.22
9.4 Max 10.9 Max 12.8 Max 14.6 Max 17.7 Max 17.7 Max 19.7 Max 21.6 Max
4000 3400 3200 3000 2800 2800 2800 2500
2500 2500 2500 2200 2500 2500 2500 2500
1 NPT 1 NPT 1 NPT 1 NPT
1/2 NPT 2 bolt A flange 1/2 NPT 2 bolt A flange 1/2 NPT 2 bolt A flange 1/2 NPT 2 bolt A flange 3/4 NPT 2 bolt A flange 3/4 NPT 2 bolt A flange 3/4 NPT 2 bolt A flange 3/4 NPT 2 bolt A flange
GAUGES & METERS
V20 Vane Pumps
CW CCW CW CW
1 1/4 NPT 1 1/4 NPT 1 1/4 NPT 1 1/4 NPT
CONTROLS
FLUID COOLERS
FLUIDYNE™ - A10V Variable Volume Piston Pumps
• Flow is proportional to drive speed and displacement • Ports located on opposing sides of pump • Port adapter flanges available upon request
• Interchangeable with Rexroth • Adjusting swash-plate design allows for smooth variation of flow • Pressure control allows to set and maintain constant pressure
HOSES & FITTINGS
Note: For use with open center systems
INLET PORT
OUTLET PORT
COMPONENTS
PART NO. ROTATION CID
GPM RPM
PSI
MOUNTING
250136 250162 250142
CW 1.71 CW 2.75 CW 4.33
22 Max 31 Max 41 Max
3000 2600 2200
4000 4000 4000
1 1/4 UNC Thread 3/4 UNC Thread 1 1/2 UNC Thread 1 UNC Thread
2 bolt B flange 2 bolt B flange 2 bolt C flange
2 UNC Thread
1 UNC Thread
BEARINGS & BUSHINGS
METARIS™ - Dump Pumps
MOBILE PRODUCTS
• Pressure balance thrust plates • Heavy duty roller bearing • Foot mount bracket sold separately
• Constructed of three piece cast iron • Interchangeable with Commercial Intertech C101 and C102 • High pressure shaft seals • Direct acting relief with load check
CUSTOM SOLUTIONS
OUTLET PORT
PART NO.
ROTATION
CID
GPM
RPM
PSI
INLET PORT
MOUNTING
250107 250112 250115
Bi-rotational
6.38 6.38
39 @ 1200 RPM 1800 39 @ 1200 RPM 1800
2500 2500
1 1/4 NPT 1 1/4 NPT
1 NPT 1 NPT
Remote Direct
CCW
Foot Mount Bracket for Dump Pump
95
Made with FlippingBook flipbook maker