page 3
FEATHERWEIGHT® Uniclic ™ Luxury Vinyl Installation Sheet
low 20-30°angle. Gradually lower the plank down flat, applying pressure inward and downward, until the end joint closes, insuring that the planks are perfectly aligned. Install remaining full planks in the first row. ▪The last plank in the first row may need to be cut. Measure the distance between the wall and the surface of the last full plank. Subtract 5/16” (8.2mm) from this measurement to allow for the spacer. If this measurement is less than 8”(20.3cm) in length, trim first plank and last plank, each no less than 8”. Planks are cut using a sharp utility knife and straight edge or carpenter’s square. Score the surface of the plank with a utility knife, and then snap the plank at the score line. ▪The remaining piece cut off from the last plank in the first row may serve as the first plank in the second row provided it is at least 8”(20.3cm) long. Always stagger end joints from row to row a minimum of 8”(20.3cm) (see figure 1). ▪Install the long side of the first plank of the second row. Remember to place a 5/16”(8.2mm) spacer between the wall and the short side of the plank. Insert the tongue side into the groove side of the previous row at a low angle and lower flat to the substrate. ▪Install the second plank of the second row. Position the long side of the plank with the tongue side overlapping the groove of the planks in the previous row approximately 1/8”. Then, angle the end joint into the previous plank. Angle the plank down and gently push in until the plank locks into the previous row (see Figure 2). Continue installing remaining planks in second row. It is important to make sure that the first two rows are straight and square or this will adversely effect the entire installation (figure 1) ▪Continue working from left to right ,row by row. Be sure to maintain a 5/16” space around all walls and vertical objects and maintain a random appearance. Offset end joints a minimum of 8”(20.3cm). ▪ Featherweight® Glueless LVT planks are unique in that they can also be installed with a pull bar or tapping block and rubber mallet in difficult areas, such as the last row, and when fitting around door trim. Use a pull bar and rubber mallet to lock the joints together in the last row. Always use a pull bar on the cut edge of the plank. Factory edges can be damaged if the pull bar is used directly against them (figure 5 A and B). ▪When fitting around door trim it will be necessary to slide the plank under the trim. This can be accomplished easily by starting the row on the side of the room with the door trim and then sliding the plank into place once it is attached. The row can be completed by inserting the tongue in to the groove or the groove into the tongue depending on the direction. A special Uniclic™ approved tapping block and pullbar can also be used to lock the joints together while the planks are in a flat position. Use a series of light taps until the joint is gradually locked together (figure 5A and 5B). FINISHING THE INSTALLATION ▪After all planks have been installed, remove spacers from perimeter of room. ·Install transition moldings. Do not fasten any moldings through the flooring. ▪Pre-drill and install quarter round or baseboard molding. Molding must be sufficient size to cover the 5/16” (8.2mm) space. Do not fasten moldings through the flooring. Fasten into the wall. ▪If not covering exposed edges with trim, fill the gap with a high quality silicone caulking. ▪Use plywood to cover the top of the flooring when moving heavy furniture or appliances into position. ▪Use proper floor protectors under the legs of furniture. ▪Post installation temperature must be maintained between 65° and 85°F. Relative humidity must be maintained between 40% and 70%. BATHROOMS When the LVT planks are installed in a bathroom, the flooring can be laid under the toilet only if the floor is separated from adjacent rooms with a doorway threshold. Otherwise the flooring should be installed around the toilet leaving a 1/8” expansion space. Use a high quality silicone caulking to fill the expansion space at the tub, shower and all wet areas to prevent surface water seepage under the floor. STAIRS Featherweight® Glueless LVT planks can be installed fully adhered over steps using a high quality pressure sensitive luxury vinyl tile adhesive. Follow the instructions on the adhesive for trowel size and drying time. Always use a flush stair nose molding to finish each step at the nose. FINISHING THE JOB Remove all spacers. Install wall trim lightly over the floor surface. Drive fasteners into the wall and not the floor. When installing transitions or moldings, do not interfere with the free movement of the flooring - do not squeeze flooring with transitions or wall base. Do not drive fasteners in to the floor. Return appliances to the room by rolling or sliding over strips of hardboard to prevent damaging the floor. FLOOR CARE • Frequently moved furniture should be equipped with felt pads to avoid scratching the floor. Heavy furniture and appliances should be equipped with non staining large surface floor protectors. Furniture with castors or wheels must be easy swiveling, large surface non-staining and suitable for resilient floors. Do not use ball type castors as they can damage the floor. • Use walk off mats at entrances to prevent dirt and grit from being tracked on to the floor. • Sweep or vacuum the floor regularly to remove loose dirt. Avoid using a vacuum with a beater bar. • Clean up spills immediately. • Damp mop as needed using clean water and a diluted vinyl floor cleaner. We recommend the BONA™ line of products. Do not use harsh cleaners or chemicals on the floor. • Avoid exposure to long periods of direct sunlight. Close blinds or drapes during peak sunlight hours Featherweight®, and Feather Lodge® are registered trademarks of TP Brands, Intl, LLC. Featherweight® planks are luxury vinyl click tile planks, part of the Feather Lodge® family of responsibly built building products. Unilin™ and Uniclic™ are names licensed under Unilin Flooring, LLC.
For further information, visit our website @ www.featherlodge.com
Made with FlippingBook flipbook maker