Turning
Cutting Data Recommandation Table
Cutting parameter recommended table of parting off and grooving application f （ mm/rev ） 0.1 0.3 0.5 0.1 0.3 0.5 0.1 0.3 0.5 0.1 0.2 0.4 AP301U AP330M AC230P AW100K f （ mm/rev ） f （ mm/rev ） f （ mm/rev ）
Materials
Brinell hardness (HB/HRC)
Tensile strength Rm(N/mm²)
ISO
Workpiece material
C≤0.25%
Annealed Annealed
125 190
428 639 708 639
180 145 130 160 130 100 220 180 160 - 145 130 115 120 100 90 160 130 115 - 130 115 100 120 100 90 130 115 100 - 145 130 115 145 130 80 160 130 115 - 115 100 80 115 100 80 115 100 80 - 130 115 100 130 115 100 130 115 100 -
- - - - - - - -
- - - - - - - -
0.25<C ≤ 0.55% 0.25<C ≤ 0.55%
Heat-treated 210
Unalloyed steel
C>0.55% C>0.55%
Annealed
190
Heat-treated 300
1013
Free cutting steel (short-chip) Annealed
220 175 300 380 430 200 300 400 200 330 200 300 230 200 260 180
745 591
Annealed
180 145 130 - 115 100 80 - 170 90 105 -
- -
- -
- -
- -
- -
- -
P
Heat-treated Heat-treated Heat-treated
1013 1282 1477
Low-alloyed steel
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Annealed
675
-
-
-
-
-
-
-
-
-
-
-
-
High-alloyed steel and high-alloyed tool steel
Hardened and tempered Hardened and tempered
1013 1361
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- - - - - - - - - -
- - - - - - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
- - - - - - - - - -
- - - - - - - - - -
Ferritic/martensitic, annealed
675
165 135 105 - 150 115 70 - 165 135 105 - 155 120 80 - 135 110 85 - 115 90 65 - 115 90 65 - 185 140 95 - 185 140 95 - 145 110 80 - 145 110 80 -
Stainless steel
Martensitic, heat-treated
1114
Austenitic, quench hardened
675
M
Stainless steel
Austenitic, precipitation hardened (PH)
1013
Austenitic/ferritic, duplex
778 400 700 200 350 400 700 400
Ferritic
115 90 65 - 115 90 65 - 200 160 120 - 200 160 120 - 160 130 100 - 160 130 100 -
Malleable cast iron
Pearlitic
Low tensile strength
Grey cast iron
K
High tensile strength/austenitic
245
Ferritic
155 265 230
- -
- -
- -
- -
Nodular cast iron
Pearlitic
GGV(CGI)
-
-
-
-
-
-
-
-
-
-
-
-
Non-aging
30
-
-
-
-
-
-
-
-
-
-
-
-
-
Wrought aluminium alloys
Aged
100
340 260
-
-
-
-
-
-
-
-
-
-
-
-
≤ 12% Si, non-aging
75
-
-
-
-
-
-
-
-
-
850 500 200
Cast aluminium alloys
≤ 12% Si, aged
90
310
-
-
-
-
-
-
-
-
-
-
-
-
N
> 12% Si, non-aging
130
450 250 340 310 380
- -
- -
- -
- -
- -
- -
- -
- -
- -
450 250 40
Magnesium alloys
70
- -
- -
- -
Unalloyed, electrolytic copper
100
-
-
-
-
-
-
-
-
-
Brass, bronze, red brass
90
-
-
-
-
-
-
-
-
-
-
-
-
Copper and copper alloys
Cu alloys, short-chipping
110 300 200 280 250 350 320 200 375 410 300 300
-
-
-
-
-
-
-
-
-
-
-
-
High-tensile, Ampco alloy
1010
-
-
-
-
-
-
-
-
-
-
-
-
Annealed
680 940 840
-
-
-
-
-
-
-
-
-
-
-
-
Fe-based
Hardened
-
-
-
-
-
-
-
-
-
-
-
-
Heat-resistant alloys
Annealed
-
-
-
-
-
-
-
-
-
-
-
-
Ni or Co based
Hardened
1180 1080
-
-
-
-
-
-
-
-
-
-
-
-
Cast
-
-
-
-
-
-
-
-
-
-
-
-
S
Pure titanium
680
-
-
-
-
-
-
-
-
-
-
-
-
Titanium alloys
α and β alloys, hardened
1260 1400 1010 1010
-
-
-
-
-
-
-
-
-
-
-
-
β alloys
-
-
-
-
-
-
-
-
-
-
-
-
Tungsten alloys
-
-
-
-
-
-
-
-
-
-
-
-
Molybdenum alloys
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
- -
Hardened and tempered Hardened and tempered Hardened and tempered Hardened and tempered
50HRC 55HRC 60HRC
-
Hardened steel
-
-
-
-
-
-
-
-
-
-
-
-
-
H
-
-
-
-
-
-
-
-
-
-
-
-
-
Chilled cast iron
50HRC
-
-
-
-
-
-
-
-
-
-
-
-
-
The recommanded cutting data always refer to general cutting conditions. The actual selection should be adjusted according to machine rigidity, tool body and workpiece conditions and coolant.
189
Made with FlippingBook - Online Brochure Maker