Milling
Solid carbide end mills
Cutting edge tolerance (mm)
Helix angles
Diameter (mm)
Series
Pictures
Catagory Teeth
Application
Material
Information
Used in carbon steel, tool steel, alloyed steel machining. The workpiece hardness is up to HRC45° Used in carbon steel, tool steel, alloyed steel machining. With 4 cutting edges, it can achieve better surface finish. The workpiece hardness is up to HRC45° Used in carbon steel, tool steel, alloyed steel machining. With 4 long edge design. The workpiece hardness is up to HRC45° Used in carbon steel, tool steel, alloyed steel machining. The round corner can prevent edge breakage during high-speed cutting. With 4 long edge design. The workpiece hardness is up to HRC45° Used in carbon steel, tool steel, alloyed steel machining. For profile milling, good toughness. The workpiece hardness is up to HRC45° High speed cutting and high feed finish cutting. Ideal choice for side finish milling. The workpiece hardness is up to HRC45° High speed cutting and high feed finish cutting. With 6 long edge design. Ideal choice for side finish milling. The workpiece hardness is up to HRC45° Design for vibration resistance. With special edge treatment. It can achieve better surface finish.
+0.00 -0.03
Universal type
M100-2ES
ECO line Z=2 35°
1-20
+0.00 -0.03
Universal type
M100-4ES
ECO line Z=4 35°
1-20
+0.00 -0.03
Universal type
M100-4EL
ECO line Z=4 35°
3-20
Universal type
M100-4RL
ECO line Z=4 30°
R±0.02
4-12
≤6±0.01 >6±0.02
Universal type
M100-2BS
ECO line Z=2 30°
2-20
+0.00 -0.03
Universal type
M105-6ES
ECO line
Z=6
45°
4-20
+0.00 -0.03
Universal type
M105-6EL
ECO line
Z=6
45°
6-20
+0.00 -0.02
Aluminium alloy
M145-2ES
ECO line Z=2 45°
3-20
Design for vibration resistance. With special edge treatment. It can achieve better surface finish.
+0.00 -0.02
Aluminium alloy
M145-3ES
ECO line Z=3 45°
3-20
Design for vibration resistance. With special edge treatment. It can achieve better surface finish.
+0.00 -0.02
Aluminium alloy
M145-3EL
ECO line Z=3 45°
4-20
Use in carbon steel, tool steel, alloyed steel machining. The workpiece hardness is up to HRC55°
+0.00 -0.02
Universal type
M110-2ES
Pro line Z=2 35°
3-20
4 cutting edges can achieve better surface finishing. The workpiece hardness is up to HRC55°
+0.00 -0.02
Universal type
M110-4ES
Pro line Z=4 35°
3-20
≤6 ±0.01 >6 ±0.02
Universal type
Use in profile machining. The workpiece hardness is up to HRC55° and high feed.
M110-2BS
Pro line Z=2 30°
3-20
For high speed finish and high feed milling. Excellent surface finishing. 1st choice for side finish milling. The workpiece hardness is up to HRC55° For rough milling steel, stainless steel, Ni- based alloyed, titanium alloyed, inconel , etc. Thanks to the fine waved cutting edge, the tool has low cutting force and high chip removal rate. Used in stainless steel, soft steel and cast iron milling. Special flute geometry and differential helix eliminate vibration. With extended edge design. The workpiece hardness is up to HRC40° Used in stainless steel, soft steel and cast iron milling. Special flute geometry and differential helix eliminate vibration. The workpiece hardness is up to HRC40° Used in stainless steel, soft steel and cast iron milling. Special flute geometry and differential helix eliminate vibration. With extended edge design. The workpiece hardness is up to HRC40° Used in stainless steel, soft steel and cast iron milling. It has close pitch to provide a better surface finish and tool life under the condition of high speed milling and cycloid milling.
+0.00 -0.02
Universal type
M115-6ES
Pro line
Z=6
45°
6-18
P 、 M 、 K 、 S
M116-4PS
Pro line
Z=4-6
45°
h10
6-20
P 、 M 、 K 、 S
≤12+0.00/-0.02 >12+0.00/-0.03
M121-4CSP
XP Line Z=4 35°/38°
4-20
P 、 M 、 K 、 S
≤12+0.00/-0.02 >12+0.00/-0.03
M121-4CS
XP Line Z=4 35°/38°
4-20
P 、 M 、 K 、 S
≤12+0.00/-0.02 >12+0.00/-0.03
M121-4ESP
XP Line Z=4 35°/38°
4-20
P 、 M 、 K 、 S
≤12+0.00/-0.02 >12+0.00/-0.03
M125-6ES
XP Line
Z=6
45°
6-20
309
Made with FlippingBook - Online Brochure Maker