Milling
Solid Carbide End Mill Eco Line Cutting Parameters
0.5D
Materials
M100-2ES
Slot milling
D
Tensile strength Rm(N/ mm²)
fz [mm/Tooth] Mill diameter [mm]
Brinell hardness (HB)
Cutting speed Vc(m/min)
Material classification
ISO
2 4
6 8
10 12 14
16
20
C ≤ 0.25%
Annealed 125
428
45~80
0.012 0.024 0.038 0.058 0.060 0.062 0.065 0.066 0.070
0.25 < C ≤ 0.55%
Annealed 190
639
45~75 0.012 0.024 0.038 0.058 0.060 0.062 0.065 0.066 0.070
0.25 < C ≤ 0.55%
Heat-treated 210
708
45~75 0.012 0.024 0.038 0.058 0.060 0.062 0.065 0.066 0.070
Unalloyed steel
Annealed 190
639
45~75 0.012 0.024 0.038 0.058 0.060 0.062 0.065 0.066 0.070
C > 0.55%
Heat-treated 300
1013
40~60
0.010 0.020 0.034 0.045 0.052 0.055 0.055 0.057 0.060
C > 0.55%
Free cutting steel (short-chip) Annealed 220
745
45~65
0.010 0.020 0.038 0.058 0.060 0.062 0.065 0.066 0.070
Annealed
175
591
45~75 0.012 0.024 0.038 0.058 0.060 0.062 0.065 0.066 0.070
P
Heat-treated
300
1013
40~60
0.010 0.020 0.034 0.045 0.052 0.055 0.055 0.057 0.060
Low-alloyed steel
Heat-treated
380
1282
40~60
0.010 0.020 0.034 0.045 0.052 0.055 0.055 0.057 0.060
Heat-treated
430
1477
30~40
0.008 0.020 0.030 0.040 0.045 0.050 0.050 0.050 0.055
Annealed
200
675
45~75 0.012 0.020 0.038 0.058 0.060 0.062 0.055 0.057 0.060
High-alloyed steel and high-alloyed tool steel
Hardened and tempered
300
1013
40~60
0.010 0.020 0.035 0.045 0.052 0.055 0.055 0.057 0.060
Hardened and tempered
400
1361
40~60 0.008 0.015 0.025 0.035 0.042 0.045 0.045 0.045 0.050
Ferritic/martensitic, annealed
200
675
35~40 0.010 0.020 0.038 0.058 0.060 0.055 0.055 0.057 0.060
Stainless steel
Martensitic, heat-treated
330
1114
30~35 0.010 0.020 0.035 0.045 0.052 0.055 0.055 0.057 0.060
Austenitic, quench hardened
200
675
30~35 0.007 0.020 0.035 0.043 0.050 0.053 0.055 0.057 0.058
M
Stainless steel
Austenitic, precipitation hardened (PH)
300
1013
30
0.004 0.015 0.030 0.032 0.035 0.040 0.043 0.045 0.050
Austenitic/ferritic, duplex
230
778
30~35 0.007 0.020 0.035 0.043 0.050 0.053 0.055 0.057 0.058
Ferritic
200
400
55~60
0.012 0.024 0.042 0.060 0.071 0.075 0.080 0.083 0.085
Malleable cast iron
Pearlitic
260
700
55~60
0.012 0.024 0.042 0.060 0.071 0.075 0.080 0.083 0.085
Low tensile strength
180
200
55~60
0.012 0.024 0.042 0.060 0.071 0.075 0.080 0.083 0.085
Grey cast iron
K
High tensile strength/austenitic
245
350
55~60
0.012 0.024 0.042 0.060 0.071 0.075 0.080 0.083 0.085
Ferritic
155
400
55~60
0.010 0.020 0.038 0.050 0.060 0.065 0.072 0.075 0.075
Nodular cast iron
Pearlitic
265
700
45~55
0.008 0.012 0.035 0.045 0.055 0.060 0.065 0.068 0.068
GGV(CGI)
230
400
55~60
0.010 0.020 0.038 0.050 0.060 0.065 0.072 0.075 0.075
Non-aging
30
-
Wrought aluminium alloys
Aged
100
340
75
260
≤ 12% Si, non-aging
Cast aluminium alloys
≤ 12% Si, aged
90
310
> 12% Si, non-aging
130
450
N
Magnesium alloys
70
250
Unalloyed, electrolytic copper
100
340
Brass, bronze, red brass
90
310
Copper and copper alloys
Cu alloys, short-chipping
110
380
High-tensile, Ampco alloy
300
1010
Annealed 200
680
Fe-based
Hardened
280
940
Heat-resistant alloys
Annealed 250
840
Ni or Co based
Hardened 350
1180
Cast
320
1080
S
Pure titanium
200
680
Titanium alloys
α and β alloys, hardened
375
1260
β alloys
410
1400
Tungsten alloys
300
1010
Molybdenum alloys
300
1010
Hardened and tempered
50HRC
-
Hardened steel
Hardened and tempered
55HRC
-
H
Hardened and tempered
60HRC
-
Chilled cast iron Hardened and tempered
50HRC
-
The cutting data are average recommended values. For special applications, adjustment is needed.
326
Made with FlippingBook - Online Brochure Maker