Milling
Solid Carbide End Mill Eco Line Cutting Parameters
Ap
Profile (Finishing)
Materials
M100-2BS
Ae
Tensile strength Rm(N/ mm²)
fz [mm/Tooth] Mill diameter [mm]
Brinell hardness (HB)
Cutting speed Vc(m/min)
Material classification
ISO
2 4
6 8
10 12 14
16
20
C ≤ 0.25%
Annealed 125
428
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
0.25 < C ≤ 0.55%
Annealed 190
639
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
0.25 < C ≤ 0.55%
Heat-treated 210
708
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
Unalloyed steel
Annealed 190
639
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
C > 0.55%
Heat-treated 300
1013
80~90
0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
C > 0.55%
Free cutting steel (short-chip) Annealed 220
745
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
Annealed
175
591
90 ~100 0.015 0.027 0.039 0.050 0.060 0.070 0.075 0.080 0.100
P
Heat-treated
300
1013
80~90
0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
Low-alloyed steel
Heat-treated
380
1282
80~90
0.010 0.020 0.030 0.041 0.045 0.050 0.055 0.060 0.070
Heat-treated
430
1477
80~90
0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
Annealed
200
675
90~100 0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
High-alloyed steel and high-alloyed tool steel
Hardened and tempered
300
1013
80~90
0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
Hardened and tempered
400
1361
80~90
0.010 0.020 0.030 0.041 0.045 0.050 0.055 0.060 0.070
Ferritic/martensitic, annealed
200
675
90~100 0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
Stainless steel
Martensitic, heat-treated
330
1114
80~90
0.012 0.023 0.035 0.045 0.052 0.060 0.065 0.070 0.085
Austenitic, quench hardened
200
675
90~100 0.009 0.016 0.023 0.029 0.035 0.041 0.045 0.051 0.060
M
Stainless steel
Austenitic, precipitation hardened (PH)
300
1013
80~90
0.007 0.013 0.020 0.025 0.030 0.035 0.040 0.045 0.050
Austenitic/ferritic, duplex
230
778
80~90
0.009 0.016 0.023 0.029 0.035 0.041 0.045 0.051 0.060
Ferritic
200
400
90 ~100
0.026 0.045 0.064 0.083 0.100 0.115 0.125 0.140 0.160
Malleable cast iron
Pearlitic
260
700
90 ~100
0.026 0.045 0.064 0.083 0.100 0.115 0.125 0.140 0.160
Low tensile strength
180
200
90 ~100
0.026 0.045 0.064 0.083 0.100 0.115 0.125 0.140 0.160
Grey cast iron
K
High tensile strength/austenitic
245
350
90 ~100
0.026 0.045 0.064 0.083 0.100 0.115 0.125 0.140 0.160
Ferritic
155
400
90 ~100 0.020 0.035 0.050 0.060 0.080 0.090 0.105 0.120 0.140
Nodular cast iron
Pearlitic
265
700
90 ~100 0.015 0.030 0.040 0.050 0.065 0.070 0.085 0.100 0.120
GGV(CGI)
230
400
90 ~100 0.020 0.035 0.050 0.060 0.080 0.090 0.105 0.120 0.140
Non-aging
30
-
Wrought aluminium alloys
Aged
100
340
75
260
≤ 12% Si, non-aging
Cast aluminium alloys
≤ 12% Si, aged
90
310
> 12% Si, non-aging
130
450
N
Magnesium alloys
70
250
Unalloyed, electrolytic copper
100
340
Brass, bronze, red brass
90
310
Copper and copper alloys
Cu alloys, short-chipping
110
380
High-tensile, Ampco alloy
300
1010
Annealed 200
680
Fe-based
Hardened
280
940
Heat-resistant alloys
Annealed 250
840
Ni or Co based
Hardened 350
1180
Cast
320
1080
S
Pure titanium
200
680
Titanium alloys
α and β alloys, hardened
375
1260
β alloys
410
1400
Tungsten alloys
300
1010
Molybdenum alloys
300
1010
Hardened and tempered
50HRC
-
Hardened steel
Hardened and tempered
55HRC
-
H
Hardened and tempered
60HRC
-
Chilled cast iron Hardened and tempered
50HRC
-
The cutting data are average recommended values. For special applications, adjustment is needed.
329
Made with FlippingBook - Online Brochure Maker