Hole machining
Recommended Cutting Speed for Materials(Dia 25.00-65.00mm)
Grade
Feed fn mm/r
Brinell hardness (HB)
Cutting speed Vc m/min
Workpiece material
Insert
Drilling dia mm
P
I
C
25.00-43.00 43.01-65.00
C=0.05-0.10% C=0.10-0.25% C=0.25-0.55% C=0.55-0.80%
125 125 150 170 210 180 275 350 200 325 180 200 200 200 300 230 200 260 180 245 160 250 230
70-130 70-130 70-130 70-130 70-120 55-110 70-120 70-120 55-110 55-110 55-110 55-110 40-110 40-110 40-110
0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.38 0.20-0.38 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.41 0.11-0.33 0.11-0.33 0.11-0.38 0.11-0.38 0.11-0.38 0.11-0.38 0.11-0.38 0.11-0.38 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.33 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30 0.09-0.30
0.14-0.45 0.14-0.45 0.14-0.45 0.14-0.45 0.20-0.45 0.20-0.45 0.20-0.45 0.20-0.45 0.20-0.40 0.20-0.40 0.20-0.45 0.20-0.45 0.20-0.45 0.20-0.45 0.20-0.35 0.20-0.35 0.24-0.41 0.24-0.41 0.24-0.41 0.24-0.41 0.24-0.41 0.24-0.41 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33 0.20-0.33
Unalloyed steel
AP301U(N)
High carbon steel
Carbon tool steel Non-Hardened
AP301U(N)
P
Low-alloyed steel
Tempered Tempered Annealed
AP301U(N)
High-alloyed steel
AP301U(N)
Hardened tool steel Non-alloyed steel Low-alloy （ alloy<5%)
Cast steel
AP301U(N)
Non-Hardened/Ferritic/martensitic
Austenitic
M
Stainless steel
AP301U(N)
Austenitic, precipitation hardened (PH)
Austenitic/ferritic, duplex
40-80
Ferritic Pearlitic
80-120 80-120 60-110 60-110 50-110 50-110 65-150 65-150 65-150 65-150 65-150 65-150 65-150 65-150 65-150
Malleable cast iron
AP301U(N)
Low tensile strength High tensile strength
Grey cast iron
AP301U(N)
K
Ferritic Pearlitic
Nodular cast iron
AP301U(N)
GGV (CGI)
non-aging
30
Wrought aluminium alloys
AP301U(N)
aged
100
≤ 12% Si, non-aging
75 90
Cast aluminium alloys
≤ 12% Si, aged
AP301U(N)
> 12% Si, non-aging
130
N
Magnesium alloy
70
Unalloyed, electrolytic copper Brass, bronze, red brass Cu alloys, short-chip High tensile, Ampco alloy
100
AP301U(N)
90
Copper and copper alloys (bronze/brass)
110 300 200 280 250 350 320 200 375 375 410
AP301U(N)
Fe-based annealed Fe-based hardened
10-55 10-55 10-55 10-55 10-55 30-60 30-60 30-60 30-60
Ni or Co-based annealed Ni or Co-based hardened
Heat-resistant alloys
AP301U(N)
Ni or Co-based cast
S
Pure titanium
α alloys
Titanium alloys
AP301U(N)
α and β alloys
β alloys
Hardened steel Chilled cast iron
Hardened and tempered
43-47 HRC 47-60 HRC
H
*) Insert position-P , I , C P=peripheral insert , I=intermediate insert, C=center insert
365
Made with FlippingBook - Online Brochure Maker