Installationsempfehlung Installation recommendations
Produkte mit Remote-Treiber Es wird empfohlen, den Treiber maximal 2 Meter vom Produkt ent- fernt zu installieren, wenn die in den geltenden Richtlinien festgele- gten EMV-Werte für die entsprechende Anwendung nicht überprüft werden können. Die Polarität der Produktkabel muss überprüft wer- den, bevor der Anschluss an die Sekundärseite des Treibers erfolgt, da eine fehlerhafte Verbindung das LED-Modul und/oder den Treiber beschädigen kann. Steuerung Die Kabel für das Steuerungssignal müssen getrennt von den Stromkabeln installiert werden. Es dürfen keine Schalter an der Sekundärseite des Treibers angebra- cht werden. Steuerung nach Leitung (Phasenschnitt) -Basissteuerung nach Leitung, keine zusätzlichen Kabel erforderlich. -Produkte mit „L“-Dimmtreiber können mit Dimmern des Typs TRIAC/ IGBT gedimmt werden; Steuerung durch Phasenanschnitt. -Produkte mit „C“-Dimmtreiber können mit IGBT-Dimmern gedimmt werden; Steuerung durch Phasenabschnitt. -Produkte mit „LC“-Dimmtreiber können mit beiden zuvor angegebe- nen Dimmertypen verwendet werden. -Es wird empfohlen, die Kompatibilität des Dimmtreibers zu überprü- fen. Push-Steuerung Erfordert ein zusätzliches Kabel. Es müssen Druckschalter vom Typ NA (normalerweise offene) verwendet werden. Kurzes Drücken schaltet das Produkt ein oder aus. Durch Gedrückthalten des Schal- ters kann die Helligkeit eingestellt werden. Steuerung 0/1–10 V Analoge Steuerung, die zwei zusätzliche Kabel mit Polarität erfordert. Ein Dimmer erzeugt ein Signal bei konstanter Spannung zwischen 0 und 10 V. Bei einer Spannung von 1 V regelt der Treiber die Helligkeit des Produkts auf das Minimum herunter, bei einer Spannung von 10 V leuchtet das Produkt hingegen mit maximaler Helligkeit. Treiber, die ein Signal mit einem Bereich von 0 bis 10 V unterstützen, können das Produkt beim Empfang von 0 V durch den Dimmer vollständig abschalten. DALI/DALI-2-Steuerung Digitales Steuerprotokoll, das von den großen Treiberherstellern als Standard im Beleuchtungssektor entwickelt wurde. Ermöglicht die Speicherung von Szenen, das Senden von Nachrichten bei Ausfall oder Ende der Produktlebensdauer, eine punktweise Steuerung und Planung des Produkts sowie ein Notfallmanagement. Erfordert zwei zusätzliche Kabel ohne Polarität. Es wird ein Kabel mit einem Quers- chnitt von 1,5 mm2 empfohlen. Die DALI-2-Zertifizierung verbessert die Kompatibilität mit DALI-Geräten. DMX-Steuerung Digitales Steuerprotokoll für spektakuläre Beleuchtungen. Erfordert zwei zusätzliche Kabel mit Polarität. Die Verwendung eines abges- chirmten, geflochtenen Kabels mit einer Impedanz von 120 Ω wird empfohlen. Casambi-Steuerung Bluetooth Mesh-Steuersystem Der Abstand zwischen den Geräten sollte 15 m nicht überschreiten und es wird empfohlen, keine Metallabdeckungen zu verwenden, die die drahtlose Kommunikation beeinträchtigen.
Products with a remote driver Install the driver within 2 metres of the product when the EMC levels for each application cannot be checked, in accordance with referen- ce standards. The polarity of the product’s cables must be checked before they are connected to the driver’s secondary side, given that the incorrect polarity may damage the LED module and/or driver. Control Control signal cables must be installed separately from power cables. Switches are not permitted on the driver’s secondary side. Phase-cut control -Basic phase-cut control. Does not require additional cables. -Products with an L-control driver: they enable control with TRIAC/ IGBT dimmers; leading-edge/forward-phase control. -Products with a C-control driver: they enable control with IGBT dim- mers; trailing-edge/reverse-phase control. -Products with LC-control driver: they allow both aforementioned types of dimmers. -Check dimmer-driver compatibility. Push control Requires an additional cable. NO (Normally Open) push buttons should be used. A quick press switches the product on or off. If the button is pressed and held, the brightness level is adjusted. 0/1-10V control Analogue control that requires two additional polarised cables. A dim- mer generates a constant voltage signal between 0 and 10V. If a vol- tage of 1V is applied, the driver will adjust the product’s brightness to the minimum, however, when a voltage of 10V is applied, the product’s brightness will be set to its maximum. The drivers that allow a control signal between 0-10V are capable of switching off the product com- pletely when they receive a signal of 0V from the dimmer. DALI/DALI-2 control Digital control protocol developed by leading driver manufacturers to create a control standard in the lighting industry. It allows scenes to be memorised, messages to be sent in the event of a breakdown or the end of the product’s life, point-to-point product control and planning, and emergency management. It requires two additional non-polari- sed cables. A cable with a cross-section of 1.5mm2 is recommended. DALI-2 certification improves interoperability between DALI devices. DMX control Digital control protocol used in the world of show lighting. It requires two additional polarised cables. Using a twisted, shielded cable with an impedance of 120Ω is recommended. Casambi control Bluetooth Mesh control system We recommend not to exceed 15m distance between devices, nor to use metal enclosures that may affect wireless communication.
Made with FlippingBook - professional solution for displaying marketing and sales documents online