Klass Single Sided Desk. Assembly Instructions
Klass Single Sided Desk
Components List
A
B
C
D
2 x Column
2 x Rail Assembly
2 x Side Bracket
2 x Foot
E
F
G
H
2 x Cable Tray Bracket (optional)
2 x Studio50 Screen Bracket (optional)
Cable Tray Bridge (optional)
GPO Plate (optional)
I
J
K
L
M
1 x Transformer Tray
Data Plate (optional accessories)
Adjustable Cable Tray (optional accessories)
1 x Switch
1 x Control Box
N
O
P
Q
R
S
1 x Power Cord
1 x Extension Cable
4 x M10x16 (accessory screws)
4 x M8x10 (accessory screws)
8 x M6x16
34 x M6x10 (accessory screws)
T
U
V
W
X
Y
4 x M6x8
10 x M5x12 (accessory screws)
12 x ST4.8x16
2 x ST3.5x16
6 x Cable Clip
12 x Washer
Tools:
Z
4 x Plastic Plug (optional)
1 x M5 Allen Key
1 x M4 Allen Key
Screwdriver (not included)
2
Klass Single Sided Desk - Assembly Instructions
Klass Single Sided Desk
Assembly Instructions
STEP 1:
B
Loosen (M6x8) screws and pull apart
2 x Rail Assembly
S
8 x M6x10
Helpful Tips: Don’t plug in the desk until handset & power box are mounted on to the desk top. It might cause errors.
1 x M5 Allen Key
STEP 2:
A
2 x Column
S
8 x M6x10
1 x M5 Allen Key
3
olgoffice.com | myolg.online
Klass Single Sided Desk Assembly Instructions
STEP 3:
D
2 x Foot
R
8 x M6x16
1 x M5 Allen Key
STEP 4:
These plugs are pre-assembled to ensure the frame remains stable during attachment to the worktop
C
2 x Side Bracket
T
4 x M6x8
Y
12 x Washer
Helpful Tips: Ensure that the washers are placed in the holes before fitting the worktop (Step 6).
1 x M5 Allen Key
4
Klass Single Sided Desk - Assembly Instructions
Klass Single Sided Desk
Assembly Instructions
STEP 5:
Skip to Step 8 if you don’t have Cable Management.
E
2 x Cable Tray Bracket (optional)
F
2 x Studio50 Screen Bracket (optional)
P
4 x M10x16
Tighten the screws after adjusting to the proper position.
S
4 x M6x10
1 x M5 Allen Key
Helpful Tips: Don’t plug in the desk until handset & power box are mounted on to the desk top. It might cause errors.
1 x M4 Allen Key
STEP 6:
J
Adjustable Cable Tray (optional)
H
GPO Plate (optional)
I
Install the GPO Plate and DATA Plate inside the cable tray with M5x12 screws.
Data Plate (optional)
S
U
6 x M6x10 6 x M5x12
1 x M5 Allen Key
Helpful Tips: Remove the pre-installed screws from the cable tray, adjust to the proper position and then tighten the screws.
1 x M4 Allen Key
5
olgoffice.com | myolg.online
Klass Single Sided Desk Assembly Instructions
STEP 7:
S
4 x M6x10
1 x M5 Allen Key
STEP 8:
M
1 x Transformer Tray
L
1 x Control Box
K
1 x Switch
V
12 x ST4.8x16
W
2 x ST3.5x16
1 x M5 Allen Key
6
Klass Single Sided Desk - Assembly Instructions
Klass Single Sided Desk Assembly Instructions
STEP 9:
Cable Connection
O
1 x Extension Cable
6 x Cable Clip
N
1 x Power Cord
Helpful Tips: Please ensure all cables are securely in place before connecting to power. Once connected to power, please perform a Manual Reset.
STEP 10:
G
Cable Tray - Bridge (optional)
S
8 x M6x10
Adjust the adjustable cable tray to the proper position and then tighten it with M6x10 screws.
1 x M5 Allen Key
7
olgoffice.com | myolg.online
Klass Single Sided Desk Direction for Use
It is necessary to be reset manually after the initial installation and power off.
MANUAL RESET
• Keep pressing down key until the desktop until display shows “E-1” and “rES” alternately and release the key. • Keep pressing down key, the desktop will move slowly down and return back until the display shows “063”.
rES
6
rES
• Release the key, the height-adjustable desk can be used normally.
Note: The anti-collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.
UP AND DOWN
• Keep pressing up key until the required height is reached.
• Keep pressing down key until the required height is reached.
Press and hold the memory key until the columns have reached the desired memory position.
SAVING POSITION
• Adjust the desktop to the height you want to save.
• Press “M” key, until the display will show “S --”
• Press “1”, and the display will show alternately as “S-1” and the desktop height.
• Press “M” key, the first memory position is set successfully. Similar process for 2 and 3 memory positions.
Before use, please make sure removing obstacle in advance and human body is in the safe position.
ANTI-COLLISION FUNCTION
• Once the desktop encounters any obstacle in its path, the screen displays “E-2”.
• The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.
8
Klass Single Sided Desk - Assembly Instructions
Klass Single Sided Desk Direction for Use
SET MINIMUM AND MAXIMUM HEIGHT
Do not enable this function only when you are really need in some situation.
• Keep pressing the key “M” for 3 seconds until the display shows “S--” to enter setup menu.
• Press up key until the display flash as “HLP”.
1 H-P
• Press “1”, the display show alternately as “H-P” and current height.
• Keep pressing up or down key until the required upper limit position is reached.
• Press “M”, the desktop height will be showed and the shelf stop position has been set. • Press “2”, the display will show alternately “L-P” and current height, keep pressing down key until the lower limit position is reached, press M, the con- tainer stop position has been set.
2
Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation position will be stored.
CHANGE THE DISPLAY UNIT(cm/inch)
• Keep pressing up key “M” until the display show “S--” to enter the setup menu.
Unt
• Press “up” key, the display will show “Unt”.
• Press “1”, and the display will show alternately as “Unt” and the desktop height unit by “cm”.
1
• Press “M” key to save the unit as cm.
• Press “2”, and the display will show alternately as “Unt” and the desktop height unit by “inch”, press the key “M” to save the unit as inch.
2
AMEND THE DESKTOP HEIGHT DISPLAYED
rES
• Keep pressing down key until the desktop until display shows “E-1” and “rES”.
• Keep pressing key “M” until the display show “Ur” and “OFF” alternatelty.
• Keep “Up” or “Dn” several times, until the display show “End” and height. (In this case, the unit is mm or inch when this system’s metric or imperial) • Press “1”,”2” and “3” respectively, and to adjust the first number, the second num - ber and the third number. If you click one, the number will increase by 1, until you get to the value you want.
1 2
• Press “M” the height has been changed to defined digit.
Note: The function enables you to change the height shows on the display based on the actual measurement.
9
olgoffice.com | myolg.online
Klass Single Sided Desk Direction for Use
The function can detect whether the motors are collected normally.
CHANGE THE DISPLAY UNIT(cm/inch)
• Once the display shows “E-3” and “rES”, it reminds you check whether any motors fail connected with control unit. Please connect the main cable again, wait at least 5 seconds.
E-3 rES
• Collect all the plugs.
rES
• Follow manual reset procedure.
With this function, you can make the control unit to factory setting.
RESET TO FACTORY SETTING
• Keep pressing “M” until the display shows “FAC”.
• Press “M”, and the control unit to factory setting (including memory position, container - and shelf - stop position, etc).
CODE MEANING
Code
Information
Operating
rES
Manual resetting
Refer to the progress of manual reset
Remove the load on desktop till it less than 800N (175 LBS) for further operation
ovr
Overloading
E-2
Anti-Collision function
It can be used normally after removing the obstacle
Operated continuously without suitable rest
dut
Make the desk rest around 15min for further operation
10
Klass Single Sided Desk - Assembly Instructions
Klass Single Sided Desk Direction for Use
TROUBLE SHOOTING
Code
Operating
E-4 / The height between two legs exceed 1 inch
Stop the operation and reset, refer to Manual reset
Check the cables and ensure they are well connected, and the height-adjustable desk can be used normally after manual reset
E-3
TECHNICAL DATA
Item
Data
Input voltage
100~240VAC
Output voltage
24VDC
Max loading
1000N
Height range (without desktop)
595 – 1245
Duty cycle
2 min on / 18 min off
11
olgoffice.com | myolg.online
Sydney 02 8188 2732 Melbourne 03 9111 0315 Brisbane 07 3733 1923 Adelaide 08 7111 0810 Perth 08 9468 2707
info@olgoffice.com
myolg.online | olgoffice.com | officedesigner.net | motionoffice.com
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12Made with FlippingBook - Share PDF online