Klass Double Sided Desk. Assembly Instructions
Klass Double Sided Desk
Components List
A
B
C
D
2 x Vertical Connecting Pipe
4 x Side Bracket
2 x Right Column
2 x Left Column
E
F
G
H
1 x Cable Tray Cover (optional)
2 x Plate (optional)
2 x Data Plate
4 x Rail
I
J
K
L
2 x Transformer Tray
2 x Switch
1 x GPO Plate
2 x Control Box
M
N
O
P
2 x Power Cord
4 x Extension Cable
4 x M6x16 Screw
28 x M6x10 Screw
T
Q
R
S
U
4 x ST3.5x16 Screw
8 x M8x18 Screw
16 x ST4.8x16 Screw
6 x M5x12
12 x M6x8 Screw
Tools:
1 x M6 Allen Key
1 x M4 Allen Key
Screwdriver (not included)
2
Klass Double Sided Desk - Assembly Instructions
Klass Double Sided Desk
Assembly Instructions
STEP 1:
A
2 x Vertical Connecting Pipe
C
2 x Right Column
D
2 x Left Column
Q
Helpful Tips: Pre-tighten the vertical connecting pipe and column by screws.
8 x M8x18
STEP 2:
If you don’t have a cable management tray, skip to Step 4.
The number of GPO plates and DATA plates is selected by you, and the number of screws is configured according to the selecting results.
GPO Plate
DATA Plate
F
1 x Cable Tray (optional)
J
H
M6 x 10 Screw
M5 x 12 Screw
GPO Plate Data Plate
P
4 x M6x10
Helpful Tips: The number of M6 x 10 illustrated is 4, the optional number is 4-8; To adjust the length of the trunking, you need to remove the two screws that were originally fixed.
S
6 x M5x12
3
olgoffice.com | myolg.online
Klass Double Sided Desk Assembly Instructions
STEP 3:
Optional Plate
G
M6 x 16 Screw
2 x Plate (optional)
O
4 x M6x16
P
M6 x 10 Screw
4 x M6x10
Helpful Tips: Install the cable tray cover after locking the cable tray screws; Install the optional plate (if Studio50 Screen is required) and tighten the screws.
1 x M5 Allen Key
STEP 4:
E
4 x Rail
P
M6 x 10 Screw
16 x M6x10
Helpful Tips: Pre-tighten the vertical connecting pipe and column by screws.
1 x M5 Allen Key
4
Klass Double Sided Desk - Assembly Instructions
Klass Double Sided Desk Assembly Instructions
STEP 5:
Transformer Tray
B
Gasket
M6 x 8 Screw
4 x Side Bracket
O
2 x Transformer Tray
W
12 x M6x8
S
4 x M6x10
M6 x 10 Screw
Helpful Tips: Insert the side brackets into column and tighten the screws; Lock the transformer tray and install the gasket.
1 x M5 Allen Key
STEP 6:
ST4.8 x 16 Tapping Screw
R
16 x ST4.8x16
Helpful Tips: It is suggested to position the worktop plates 25mm from the edge of the desktop and tighten screws.
Screwdriver (not included)
5
olgoffice.com | myolg.online
Klass Double Sided Desk Assembly Instructions
STEP 7:
ST3.5 x 16 Tapping Screw
I
2 x Switch
T
4 x ST3.5x16
Helpful Tips: Install the switch on suitable position of desktop edge to avoid interference with humans or chairs, display screen facing out, and tighten screws.
Screwdriver (not included)
STEP 8:
N
4 x Extension Cable
6 x Cable Clip
M
2 x Power Cord
Helpful Tips: Tidy up all the power cables with cable clip.
6
Klass Double Sided Desk - Assembly Instructions
Klass Double Sided Desk
Direction for Use
It is necessary to be reset manually after the initial installation and power off.
MANUAL RESET
• Keep pressing down key until the desktop until display shows “E-1” and “rES” alternately and release the key. • Keep pressing down key, the desktop will move slowly down and return back until the display shows “063”.
rES
6
rES
• Release the key, the height-adjustable desk can be used normally.
Note: The anti-collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.
UP AND DOWN
• Keep pressing up key until the required height is reached.
• Keep pressing down key until the required height is reached.
Press and hold the memory key until the columns have reached the desired memory position.
SAVING POSITION
• Adjust the desktop to the height you want to save.
• Press “M” key, until the display will show “S --”
• Press “1”, and the display will show alternately as “S-1” and the desktop height.
• Press “M” key, the first memory position is set successfully. Similar process for 2 and 3 memory positions.
Before use, please make sure removing obstacle in advance and human body is in the safe position.
ANTI-COLLISION FUNCTION
• Once the desktop encounters any obstacle in its path, the screen displays “E-2”.
• The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.
7
olgoffice.com | myolg.online
Klass Double Sided Desk Direction for Use
SET MINIMUM AND MAXIMUM HEIGHT
Do not enable this function only when you are really need in some situation.
• Keep pressing the key “M” for 3 seconds until the display shows “S--” to enter setup menu.
• Press up key until the display flash as “HLP”.
1 H-P
• Press “1”, the display show alternately as “H-P” and current height.
• Keep pressing up or down key until the required upper limit position is reached.
• Press “M”, the desktop height will be showed and the shelf stop position has been set. • Press “2”, the display will show alternately “L-P” and current height, keep pressing down key until the lower limit position is reached, press M, the con- tainer stop position has been set.
2
Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation position will be stored.
CHANGE THE DISPLAY UNIT(cm/inch)
• Keep pressing up key “M” until the display show “S--” to enter the setup menu.
Unt
• Press “up” key, the display will show “Unt”.
• Press “1”, and the display will show alternately as “Unt” and the desktop height unit by “cm”.
1
• Press “M” key to save the unit as cm.
• Press “2”, and the display will show alternately as “Unt” and the desktop height unit by “inch”, press the key “M” to save the unit as inch.
2
AMEND THE DESKTOP HEIGHT DISPLAYED
rES
• Keep pressing down key until the desktop until display shows “E-1” and “rES”.
• Keep pressing key “M” until the display show “Ur” and “OFF” alternatelty.
• Keep “Up” or “Dn” several times, until the display show “End” and height. (In this case, the unit is mm or inch when this system’s metric or imperial) • Press “1”,”2” and “3” respectively, and to adjust the first number, the second num - ber and the third number. If you click one, the number will increase by 1, until you get to the value you want.
1 2
• Press “M” the height has been changed to defined digit.
Note: The function enables you to change the height shows on the display based on the actual measurement.
8
Klass Double Sided Desk - Assembly Instructions
Klass Double Sided Desk Direction for Use
The function can detect whether the motors are collected normally.
CHANGE THE DISPLAY UNIT(cm/inch)
• Once the display shows “E-3” and “rES”, it reminds you check whether any motors fail connected with control unit. Please connect the main cable again, wait at least 5 seconds.
E-3 rES
• Collect all the plugs.
rES
• Follow manual reset procedure.
With this function, you can make the control unit to factory setting.
RESET TO FACTORY SETTING
• Keep pressing “M” until the display shows “FAC”.
• Press “M”, and the control unit to factory setting (including memory position, container - and shelf - stop position, etc).
CODE MEANING
Code
Information
Operating
rES
Manual resetting
Refer to the progress of manual reset
Remove the load on desktop till it less than 800N (175 LBS) for further operation
ovr
Overloading
E-2
Anti-Collision function
It can be used normally after removing the obstacle
Operated continuously without suitable rest
dut
Make the desk rest around 15min for further operation
9
olgoffice.com | myolg.online
Klass Double Sided Desk Direction for Use
TROUBLE SHOOTING
Code
Operating
E-4 / The height between two legs exceed 1 inch
Stop the operation and reset, refer to Manual reset
Check the cables and ensure they are well connected, and the height-adjustable desk can be used normally after manual reset
E-3
TECHNICAL DATA
Item
Data
Input voltage
100~240VAC
Output voltage
24VDC
Max loading
1000N
Height range (without desktop)
595 – 1245
Duty cycle
2 min on / 18 min off
10
Klass Double Sided Desk - Assembly Instructions
Sydney 02 8188 2732 Melbourne 03 9111 0315 Brisbane 07 3733 1923 Adelaide 08 7111 0810 Perth 08 9468 2707
info@olgoffice.com
myolg.online | olgoffice.com | officedesigner.net | motionoffice.com
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11Made with FlippingBook - Share PDF online