Klass 90° Workstation. Assembly Instructions
Klass 90° Workstation
Components List
A
B
C
D
2 x Inside Bracket
2 x Column
1 x Outside Bracket
1 x Column w/ Leveling Pad
E
F
G
H
2 x Telescopic Frame
1 x Short Girder
2 x Rail
2 x Foot
I
J
1 x Switch
1 x Control Box
K
L
M
N
1 x Power Cord
1 x Extension Cable
8 x M6x16 Screw
26 x M6x10 Screw
O
P
Q
22 x ST4.8x16 Screw
4 x ST3.5x16 Screw
4 x M6x8 Screw
Tools:
1 x M6 Allen Key
1 x M4 Allen Key
Screwdriver (not included)
2
Klass 90° Workstation - Assembly Instructions
Klass 90° Workstation
Assembly Instructions
STEP 1:
B
2 x Column
E
2 x Telescopic Frame
N
Loosen (M6x8) screws and pull apart
8 x M6x10
Helpful Tips: Install the column with levelling pad in the middle leg.
1 x M5 Allen Key
STEP 2:
F
1 x Short Girder
G
2 x Rail
N
4 x M6x10
Helpful Tips: You can chose any of the 4 available positions to install the return depending on the desk configuration.
1 x M5 Allen Key
3
olgoffice.com | myolg.online
Klass 90° Workstation Assembly Instructions
STEP 3:
D
1 x Column w/ Leveling Pad
S
8 x M6x10
1 x M5 Allen Key
STEP 4:
A
2 x Inside Bracket
C
1 x Outside Bracket
N
2 x M6x10
Q
4 x M6x8
Helpful Tips: Fix the side bracket with M6x8 screws, then put the washers beside M6x8 screws.
1 x M5 Allen Key
4
Klass 90° Workstation - Assembly Instructions
Klass 90° Workstation Assembly Instructions
STEP 5:
H
2 x Foot
M
8 x M6x16
Helpful Tips: If you are installing a Klass Cable Tray on the workstation, you may need to swap the foot plate on the corner leg for a foot to get the configuration shown, and the lugs facing out from the main desk.
1 x M5 Allen Key
STEP 6:
N
4 x M6x10
1 x M5 Allen Key
5
olgoffice.com | myolg.online
Klass 90° Workstation Assembly Instructions
STEP 7:
O
20 x ST4.8x16 Screw
Screwdriver (not included)
STEP 8:
J
1 x Control Box
I
1 x Switch
O
2 x ST4.8x16
P
2 x ST3.5x16
1 x M5 Allen Key
6
Klass 90° Workstation - Assembly Instructions
Klass 90° Workstation
Cable Connection
STEP 9:
L
1 x Extension Cable
6 x Cable Clip
K
1 x Power Cord
7
olgoffice.com | myolg.online
Klass 90° Workstation Direction for Use
It is necessary to be reset manually after the initial installation and power off.
MANUAL RESET
• Keep pressing down key until the desktop until display shows “E-1” and “rES” alternately and release the key. • Keep pressing down key, the desktop will move slowly down and return back until the display shows “063”.
rES
6
rES
• Release the key, the height-adjustable desk can be used normally.
Note: The anti-collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.
UP AND DOWN
• Keep pressing up key until the required height is reached.
• Keep pressing down key until the required height is reached.
Press and hold the memory key until the columns have reached the desired memory position.
SAVING POSITION
• Adjust the desktop to the height you want to save.
• Press “M” key, until the display will show “S --”
• Press “1”, and the display will show alternately as “S-1” and the desktop height.
• Press “M” key, the first memory position is set successfully. Similar process for 2 and 3 memory positions.
Before use, please make sure removing obstacle in advance and human body is in the safe position.
ANTI-COLLISION FUNCTION
• Once the desktop encounters any obstacle in its path, the screen displays “E-2”.
• The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.
8
Klass 90° Workstation - Assembly Instructions
Klass 90° Workstation Direction for Use
SET MINIMUM AND MAXIMUM HEIGHT
Do not enable this function only when you are really need in some situation.
• Keep pressing the key “M” for 3 seconds until the display shows “S--” to enter setup menu.
• Press up key until the display flash as “HLP”.
1 H-P
• Press “1”, the display show alternately as “H-P” and current height.
• Keep pressing up or down key until the required upper limit position is reached.
• Press “M”, the desktop height will be showed and the shelf stop position has been set. • Press “2”, the display will show alternately “L-P” and current height, keep pressing down key until the lower limit position is reached, press M, the con- tainer stop position has been set.
2
Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new upper or lower limitation position will be stored.
CHANGE THE DISPLAY UNIT(cm/inch)
• Keep pressing up key “M” until the display show “S--” to enter the setup menu.
Unt
• Press “up” key, the display will show “Unt”.
• Press “1”, and the display will show alternately as “Unt” and the desktop height unit by “cm”.
1
• Press “M” key to save the unit as cm.
• Press “2”, and the display will show alternately as “Unt” and the desktop height unit by “inch”, press the key “M” to save the unit as inch.
2
AMEND THE DESKTOP HEIGHT DISPLAYED
rES
• Keep pressing down key until the desktop until display shows “E-1” and “rES”.
• Keep pressing key “M” until the display show “Ur” and “OFF” alternatelty.
• Keep “Up” or “Dn” several times, until the display show “End” and height. (In this case, the unit is mm or inch when this system’s metric or imperial) • Press “1”,”2” and “3” respectively, and to adjust the first number, the second num- ber and the third number. If you click one, the number will increase by 1, until you get to the value you want.
1 2
• Press “M” the height has been changed to defined digit.
Note: The function enables you to change the height shows on the display based on the actual measurement.
9
olgoffice.com | myolg.online
Klass 90° Workstation Direction for Use
The function can detect whether the motors are collected normally.
CHANGE THE DISPLAY UNIT(cm/inch)
• Once the display shows “E-3” and “rES”, it reminds you check whether any motors fail connected with control unit. Please connect the main cable again, wait at least 5 seconds.
E-3 rES
• Collect all the plugs.
rES
• Follow manual reset procedure.
With this function, you can make the control unit to factory setting.
RESET TO FACTORY SETTING
• Keep pressing “M” until the display shows “FAC”.
• Press “M”, and the control unit to factory setting (including memory position, container - and shelf - stop position, etc).
CODE MEANING
Code
Information
Operating
rES
Manual resetting
Refer to the progress of manual reset
Remove the load on desktop till it less than 800N (175 LBS) for further operation
ovr
Overloading
E-2
Anti-Collision function
It can be used normally after removing the obstacle
Operated continuously without suitable rest
dut
Make the desk rest around 15min for further operation
10
Klass 90° Workstation - Assembly Instructions
Klass 90° Workstation Direction for Use
TROUBLE SHOOTING
Code
Operating
E-4 / The height between two legs exceed 1 inch
Stop the operation and reset, refer to Manual reset
Check the cables and ensure they are well connected, and the height-adjustable desk can be used normally after manual reset
E-3
TECHNICAL DATA
Item
Data
Input voltage
100~240VAC
Output voltage
24VDC
Max loading
1000N
Height range (without desktop)
595 – 1245
Duty cycle
2 min on / 18 min off
11
olgoffice.com | myolg.online
Sydney 02 8188 2732 Melbourne 03 9111 0315 Brisbane 07 3733 1923 Adelaide 08 7111 0810 Perth 08 9468 2707
info@olgoffice.com
myolg.online | olgoffice.com | officedesigner.net | motionoffice.com
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12Made with FlippingBook - Share PDF online