53 D
41610
41450
4017
41500
41490
8699
8701
40100
8695
8697
8705
18650
8696
60050
51797
51795
58100
8629
3053
3046
42900
42890
42910
Number
Description
Includes
Price
PULLERS, SEPARATORS, HUB TOOLS
ATD-3046
$39.19 Call for Price $20.59 $21.49
Pitman Arm Puller Heavy-Duty Pitman Arm Spreader Ball Joint Separator Tie Rod Separator
Heavy-duty center screw and heat treated yoke drop forged from high grade alloy steel for a safe and steady pull. Heavy-duty yoke eliminates spreading and breakage.
MTI-18650
Spread the open end of a pitman arm for easy removal on Class 3-8 vehicles. Easily install bearing cups of SPL series u-joints into full round yokes.
ATD-8700 ATD-8701 LIS-41500
15/16” Opening x 12” Long 5/8” Opening x 16” Long
Call for Price
Pickle Fork Kit
Kit consists of (3) forks and (2) handles; (1) for manual hammering and (1) for use with an air hammer (.401” shank). Heavy-duty forgings, handles are heat-treated alloy steel.
5-Pc. Ball Joint and Tie Rod Separator Set 12-Pc. Inner Tie Rod Tool Set Wheel Hub Removal Tool
ATD-8705
Made of heavy, drop-forged chrome vanadium steel. Includes: (3) Forks: 11/16”, 15/16” and 1-1/8”, (1) Handle for use with air hammer and (1) Handle for use with manual hammer $55.59
The long socket slips over tie rod end and crows foot engages on socket for easy removal and installation of tie rods with inaccessible wrench flats. Includes: (12) Crowsfeet: 1-3/16”, 1-1/4”, 1-3/8”, 1-1/2”, 1-5/16”, 1-7/16”, 29mm, 32.5mm, 33.6mm, 38.4mm, 40mm and 42mm to fit many cars, trucks and SUVs. Call for Price Safely removes frozen hub assemblies instantly. Universal mount fits all axle bolted hubs (5, 6 and 8 lug hubs). Mounts to 2 studs using supplied flange nuts. Use with 5 lbs. hammer to knock frozen hubs out of axles. 3/4” steel backing plate and reinforced striking plate for long life. $173.29 Fits on most 5, 6 and 8 lug hub assemblies found on cars and trucks. Bolt the 1/2” thick driving plate to the hub using the hardened washers and existing lug nuts. Insert the hardened thread forcing screw to push against a solid surface to loosen the hub assembly Call for Price Slide hammer pulls many flange-type rear axles and axle bearings. Includes: (3) bearing adapters, (1) 5/8”-18T x 22-1/2” slide screw, (1) 5/8” lock nut, (1) axle yoke, (1) 3.75 lbs. slide hammer, (1) bearing hook. $169.79
LIS-58100
ATD-8629
LIS-40100
Hub Remover
ATD-3053
Rear Axle Puller Set
Call for Price Call for Price
Separates half-shafts from transaxle. Shim tool is included to fill gaps on some applications. Better and safer than hammer and bar. Both are 14” / 36cm long with 2” / 51mm opening. Machine forged for strength and durability. Fully Heat-treated, High-strength Cast Steel Tools for Removing Stubborn Pitman Arms. 41450 works on pitman arms on medium duty trucks and other vehicles with pitman arms held on with a nut. For impact use.
CCT-4017
Axle Popper Kit 2-Pc.
Intermediate Pitman Arm Puller Pitman Arm Puller For M100 Sheppard Pitman Arm Puller For M110 Sheppard 15/16” Pneumatic Ball Joint Separator 21/32” Pneumatic Tie Rod Separator U-Joint Puller, Small U-Joint Puller, Medium
LIS-41450
Fully Heat-treated, High-strength Cast Steel Tools for Removing Stubborn Pitman Arms. 41490 works on Sheppard M100 steering gears found on many Class 6-8 vehicles. For impact use. Call for Price Fully Heat-treated, High-strength Cast Steel Tools for Removing Stubborn Pitman Arms. 41610 works on Sheppard M110 steering gears found on many Class 6-8 vehicles. For impact use. Call for Price
LIS-41490
LIS-41610
Call for Price Call for Price
TIT-51795
Separates ball joints with minimal shock to components. Engineered with a 0.401. Overall length: 3”; Fork width: 15/16”; Material: Chrome Moly Alloy Steel
TIT-51797
Separates tie rods with minimal shock to components. Engineered with a 0.401. Overall length: 3”; Fork width: 21/32”; Material: Chrome Moly Alloy Steel
Call for Price Call for Price
LIS-42890 LIS-42900
Quickly and easily remove sealed U-Joint caps without damage to driveshafts, yokes or bearing caps. Works on cars, light-duty trucks and agriculural equipment with 1” to 1.25” caps Quickly and easily remove sealed U-Joint caps without damage to driveshafts, yokes or bearing caps. Works on Class 7 and 8 trucks with 1.5” to 2.2” caps Quickly and easily remove sealed U-Joint caps without damage to driveshafts, yokes or bearing caps. Works on cars, medium-duty trucks, agriculural equipment and light industrial vehicles with 1.125” to 1.7” caps
Call for Price
LIS-42910
U-Joint Puller, Large
For use on yokes with a bearing diameter between 1-7/8” and 2-13/16”. These yokes are commonly found on Class 6-8 trucks. Kit comes with strong, grade eight bolts. All components are heat-treated. Call for Price
LIS-60050
Heavy-Duty Yoke Puller
BALL JOINT SERVICE
XL C-Frame Ball Joint Press
Extra-large ball joint press for maximum clearance. Will work with ATD and other ball joint removal and installation adapters. Kit includes long and short drive screws for shorter working length. 9.1” throat; 11.9” length.
ATD-8695
$106.29
Master Ball Joint Service Set Deluxe Ball Joint Service Set
Live center forcing screw plug. Heavy-duty steel and cast metal construction. Includes all receiver tubes and adapters needed to work on press-fit upper and lower ball joints on most 2WD and 4WD pickups, vans and SUVs thru 2006. $206.69 Includes: C-frame press & (3) receiver tubes: 2-3/4” x 3”, 2-1/4” x 2-1/2” and 1-3/4” x 2”. Adapters for ‘67-current 1/2 and 3/4 Ton 4WD vehicles having the Dana 44 front axle (found on Ford, GM, Dodge, IHC & Jeep vehicles). $97.59
ATD-8699
ATD-8696
Add-On Service Set for ATD-8696
ATD-8697
$91.69
Includes all the receiver tubes and adapters needed to work on most GM, Ford and Dodge 2WD and 4WD pickups, vans SUVs thru current.
Made with FlippingBook flipbook maker