AC5000S Brochure -2020

CAT.AC5000SBROCHURE.10/20

Coated Turning Grades for Heat Resistant Alloys

Ready to Create New Standards AC5015S / AC5025S

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S

• Application Range

AC5015S

Excellent Wear Resistance

Wear Resistance 2 x Conventional Types

AC5015S Most Recommended for Turning of Exotic Alloys

AC520U (Conventional AC5025S Material)

AC5025S

AC5025S Heavy Interrupted/Oxide Cutting

AC510U (Conventional AC5015S Material)

Fracture Resistance 1.5 x Conventional Types

Stable

High Precision Machining AC1030U (G Class Precision)

AC6040M (M Class Precision)

AC1030U Try the following grades if even greater toughness is required. Ground Precision AC6040M Molded Precision

Finishing Roughing Continuous Cut Light Interrupted Interrupted Cut

• AC5015S/AC5025S Features

AC5015S / AC5025S

New PVD-Coating Technology Absotech ®

Excellent Cutting Edge Quality

Newly Developed Highly Adhesive Technology Greatly improved film coating adhesion realizes excellent boundary defect resistance . Newly Developed Rigid Carbide Substrate Material Introduction of a revolutionary new sintering process enables hardness to be maintained while greatly improving rigidity, realizing reduces notch wear and chipping resistant performance. Highly heat-resistant ultra-multi-layer thin-film AlTiSiN structure realizes excellent crater wear resistance and flank wear resistance.

50µm

Conventional Tool

50µm

• Recommended Cutting Conditions

(Red text indicates 1st recommendation.)

Cutting Conditions

Cutting State

Min. - Optimum - Max.

Chipbreaker

Grade

Material

Depth of Cut a p (in)

Cutting Speed v c (SFM)

Feed Rate f (IPR)

AC5015S AC5025S AC5015S AC5025S AC5015S AC5025S AC5015S AC5025S

-

-

-

-

-

-

EEF

360

230

164

0.008

0.005

0.004

0.059

0.020

0.007

Finishing

Heat Resistant Alloy ( Ni Base Material Fe Base Material Co Base Material )

-

-

-

-

-

-

EEX

295

197

131

0.012

0.008

0.004

0.157

0.039

0.020

Light

-

-

-

-

-

-

EEG

295

197

131

0.012

0.010

0.006

0.157

0.079

0.020

Medium

-

-

-

-

-

-

EEM

262

180

98

0.016

0.010

0.008

0.157

0.079

0.039

Rough

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S • Wear Resistance of AC5015S New PVD Coating Technology Absotech®Bronze Reduces Wear

0.020

Competitor's Product A (S10 PVD)

AC5015S

Part Material: Insert: Cutting Conditions:

Inconel 718 (44HRC) CNMG432 v c = 131 SFM f = 0.004 IPR, a p =0.060 in, Wet

D

0.016

0.012

Conventional Tool A

13 Minutes Machining

13 Minutes Machining

D D

0.008

█ D D D █

Wear Resistance Compared to Conventional 2 x

0.004

█ D D

0 5 10 15 20 25 30

35

Competitor's Product A

AC5015S

Cutting Time (min)

• Fracture Resistance of AC5015S Newly Developed Hard Base Material Suppresses Notch Wear

25

Hastelloy (22HRC) CNMG432 v c = 164 SFM f = 0.004 IPR, a p =0.060 in, Wet

Part Material: Insert: Cutting Conditions:

Fracture Resistance Compared to Conventional 1.5 x

20

15

10 Minutes Machining

13 Minutes Machining

10

5

0

AC5015S

Conventional Tool B

Competitor's Product B (S10 PVD)

Competitor's Product B

AC5015S

• Wear Resistance of AC5025S New PVD Coating Technology Absotech®Bronze Notch Wear

0.016

Competitor's Product C (S20 PVD)

Part Material: Insert: Cutting Conditions:

Inconel 718 (44HRC) CNMG432 v c = 131 SFM f =0.004 IPR, a p =0.060 in, Wet

AC5025S

Conventional Tool C

0.012

9 Minutes Machining

9 Minutes Machining

0.008

0.004

 

Wear Resistance Compared to Conventional 2.5 x

█  

0

5

10

15

20

25

Competitor's Product C (S20 PVD)

AC5025S

Cutting Time (min)

• Fracture Resistance of AC5025S Newly Developed Hard Base Material Suppresses Boundary Defects

60

Hastelloy (22HRC) CNMG432 v c = 164 SFM f =0.004 IPR, a p =0.060 in, Wet

Part Material: Insert: Cutting Conditions:

Fracture Resistance Compared to Conventional 1.5 x

50

40

35 Minutes Machining

37 Minutes Machining

30

20

10

0

AC5025S

Conventional Tool D

Competitor's Product D (S20 PVD)

Competitor's Product D

AC5025S

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S

AC5015S & AC5025S Availabilty - Negative Inserts

CNGG 80° Diamond/Negative

CNMM 80° Diamond/Negative

SNMG 90° Square/Negative

Sumitomo Catalog Number

Sumitomo Catalog Number

Sumitomo Catalog Number

Chipbreaker Type

Chipbreaker Type

Chipbreaker Type

Finishing SNMG432ESU l l .500.1875 .0313 .2031 Finishing SNMG431EEF l  .500.1875 .0156 .2031 SNMG432EEF l  .500.1875 .0313 .2031

CNGG430ESU l l .500.1875 .0039 .2031 CNGG430.5ESU l l .500.1875 .0078 .2031 CNGG431ESU l l .500.1875 .0156 .2031 CNGG432ESU l l .500.1875 .0313 .2031 CNGG430.5EEF l l .500.1875 .0078 .2031 CNGG431EEF l l .500.1875 .0156 .2031 CNGG432EEF  l .500.1875 .0313 .2031

CNMM432ENP  .500.1875.0313 .2031 CNMM433ENP  .500.1875.0469 .2031 CNMM434ENP  .500.1875.0625 .2031 CNMM542ENP  .625 .250 .0313 .250 CNMM543ENP  .625 .250 .0469 .250 CNMM544ENP  .625 .250 .0625 .250 CNMM642ENP  .750 .250 .0313 .3126 CNMM643ENP  .750 .250 .0469 .3126 CNMM644ENP  .750 .250 .0625 .3126 CNMM646ENP  .750 .250 .0938 .3126

Finishing

SNMM432ENP  .500.1875.0313.2031 SNMM433ENP  .500.1875.0469.2031 SNMM434ENP  .500.1875.0625.2031 SNMM643ENP  .750 .250 .0469.3126 SNMM644ENP  .750 .250 .0625.3126 SNMG432EEM l l .500.1875 .0313 .2031 SNMG433EEM l l .500.1875 .0469 .2031 SNMG542EEM  .625 .250 .0313 .250 SNMG543EEM l l .625 .250 .0469 .250 SNMG544EEM l l .625 .250 .0625 .250 SNMG643EEM l l .750 .250 .0469 .3126 SNMG644EEM l l .750 .250 .0625 .3126 SNMG646EEM  .750 .250 .0938 .3126 SNMG866EEM  l 1.00 .375 .0938 .3622 SNMG432EMU l l .500.1875 .0313 .2031 SNMG433EMU l l .500.1875 .0469 .2031 SNMG542EMU  .625 .250 .0313 .250 SNMG543EMU l l .625 .250 .0469 .250 SNMG544EMU  l .625 .250 .0625 .250 SNMG643EMU l l .750 .250 .0469 .3126 SNMG644EMU l l .750 .250 .0625 .3126 SNMG646EMU  .750 .250 .0938 .3126 SNMG866EMU  1.00 .375 .0938 .3622 SNMG432ENZ  .500.1875 .0313 .2031 SNMG433ENZ  .500.1875 .0469 .2031 SNMG431EEX l l .500.1875 .0156 .2031 SNMG432EEX l l .500.1875 .0313 .2031 SNMG433EEX l l .500.1875 .0469 .2031 SNMG543EEX  l .625 .250 .0469 .250 SNMG643EEX  l .750 .250 .0469 .3126 SNMG432EUP l l .500.1875 .0313 .2031 SNMG433EUP  l .500.1875 .0469 .2031 SNMG431EGU  l .500.1875 .0156 .2031 SNMG432EGU  l .500.1875 .0313 .2031 SNMG433EGU  .500.1875 .0469 .2031 SNMG431EEG  l .500.1875 .0156 .2031 SNMG432EEG l l .500.1875 .0313 .2031 SNMG433EEG l l .500.1875 .0469 .2031 SNMG542EEG  .625 .250 .0313 .250 SNMG543EEG l l .625 .250 .0469 .250 SNMG544EEG  .625 .250 .0625 .250 SNMG643EEG l l .750 .250 .0469 .3126 SNMG644EEG  l .750 .250 .0625 .3126

Rough to Heavy Cutting

Light to Medium Cutting Light to Medium Cutting Medium Cutting

Finishing

CNMG 80° Diamond/Negative Fine Finishing CNMA 80° Diamond/Negative - CNMA432 CNGP 80° Diamond/Negative - CNGP432 CNGP433

l l .500.1875 .0313 .2031 l l .500.1875 .0469 .2031

DNGG 55° Diamond/Negative DNGA 55° Diamond/Negative — DNGA431

 l .500 .1875.0156.2031

l  .500.1875 .0313 .2031

Finishing DNGG430.5ESU l l .500.1875.0078.2031 DNGG431ESU l l .500.1875.0156.2031 DNGG432ESU l l .500.1875.0313.2031 Finishing DNGG431EEF l l .500.1875.0156.2031 DNGG432EEF l l .500.1875.0313.2031 Medium Cutting DNGG431EEG l l .500.1875.0156.2031 DNGG432EEG l l .500.1875.0313.2031

CNMG431EFL  .500.1875.0156.2031 CNMG432EFL  .500.1875.0313.2031 CNMG430.5ESU l l .500.1875.0078.2031 CNMG431ESU l l .500.1875.0156.2031 CNMG432ESU l l .500.1875.0313.2031 CNMG433ESU l l .500.1875.0469.2031 CNMG331EEF  .375.1875.0156 .150 CNMG332EEF l  .375.1875.0313 .150 CNMG431EEF l l .500.1875.0156.2031 CNMG432EEF l l .500.1875.0313.2031 CNMG433EEF l l .500.1875.0469.2031 CNMG431EEX l l .500.1875.0156.2031 CNMG432EEX l l .500.1875.0313.2031 CNMG433EEX l l .500.1875.0469.2031 CNMG543EEX l l .625 .250 .0469 .250 CNMG643EEX l l .750 .250 .0469.3126 CNMG431EUP l l .500.1875.0156.2031 CNMG432EUP l l .500.1875.0313.2031 CNMG433EUP l l .500.1875.0469.2031 CNMG431EGU l l .500.1875.0156.2031 CNMG432EGU l l .500.1875.0313.2031 CNMG433EGU l l .500.1875.0469.2031 CNMG332EEG  .375.1875.0313 .150 CNMG333EEG  .375.1875.0469 .150 CNMG431EEG l l .500.1875.0156.2031 CNMG432EEG l l .500.1875.0313.2031 CNMG433EEG l l .500.1875.0469.2031 CNMG542EEG l l .625 .250 .0313 .250 CNMG543EEG l l .625 .250 .0469 .250 CNMG544EEG  .625 .250 .0625 .250 CNMG643EEG l l .750 .250 .0469.3126 CNMG644EEG l l .750 .250 .0625.3126 CNMG432EEM l l .500.1875.0313.2031 CNMG433EEM l l .500.1875.0469.2031 CNMG434EEM l l .500.1875.0625.2031 CNMG542EEM  l .625 .250 .0313 .250 CNMG543EEM l l .625 .250 .0469 .250 CNMG544EEM l l .625 .250 .0625 .250 CNMG643EEM l l .750 .250 .0469.3126 CNMG644EEM l l .750 .250 .0625.3126 CNMG646EEM  .750 .250 .0938.3126 CNMG866EEM  l 1.00 .375 .0938.3622 CNMG432EMU l l .500.1875.0313.2031 CNMG433EMU l l .500.1875.0469.2031 CNMG434EMU l l .500.1875.0625.2031 CNMG542EMU l l .625 .250 .0313 .250 CNMG543EMU l l .625 .250 .0469 .250 CNMG544EMU  l .625 .250 .0625 .250 CNMG642EMU l .750 .250 .0313.3126 CNMG643EMU l l .750 .250 .0469.3126 CNMG644EMU  l .750 .250 .0625.3126 CNMG646EMU  .750 .250 .0938.3126 CNMG866EMU  1.00 .375 .0938.3622 CNMG432ENZ  .500.1875.0313.2031 CNMG433ENZ  .500.1875.0469.2031

Medium Cutting

Finishing

DNMG 55° Diamond/Negative

DNMG331ESU  l .375.1875.0156 .150 DNMG332ESU l .375.1875.0313 .150 DNMG430.5ESU l l .500.1875.0078.2031 DNMG431ESU l l .500.1875.0156.2031 DNMG432ESU l l .500.1875.0313.2031 DNMG433ESU l l .500.1875.0469.2031 DNMG441ESU  .500 .250 .0156.2031 DNMG442ESU  .500 .250 .0313.2031 DNMG331EEF  l .375.1875.0156 .150 DNMG332EEF l l .375.1875.0313 .150 DNMG333EEF  .375.1875.0469 .150 DNMG431EEF l l .500.1875.0156.2031 DNMG432EEF l l .500.1875.0313.2031 DNMG433EEF l  .500.1875.0469.2031 DNMG441EEF  .500 .250 .0156.2031 DNMG442EEF  .500 .250 .0313.2031 DNMG443EEF  .500 .250 .0469.2031 DNMG431EEX l l .500.1875.0156.2031 DNMG432EEX l l .500.1875.0313.2031 DNMG433EEX l l .500.1875.0469.2031 DNMG441EEX  .500 .250 .0156.2031 DNMG442EEX  .500 .250 .0313.2031 DNMG443EEX  .500 .250 .0469.2031 DNMG431EUP l l .500.1875.0156.2031 DNMG432EUP l l .500.1875.0313.2031 DNMG433EUP l l .500.1875.0469.2031 DNMG431EGU  l .500.1875.0156.2031 DNMG432EGU l l .500.1875.0313.2031 DNMG433EGU  .500.1875.0469.2031 DNMG332EEG  l .375.1875.0313 .150 DNMG333EEG  .375.1875.0469 .150 DNMG431EEG l l .500.1875.0156.2031 DNMG432EEG l l .500.1875.0313.2031 DNMG433EEG l l .500.1875.0469.2031 DNMG441EEG  .500 .250 .0156.2031 DNMG442EEG l  .500 .250 .0313.2031 DNMG443EEG  .500 .250 .0469.2031 DNMG432EEM l l .500.1875.0313.2031 DNMG433EEM l l .500.1875.0469.2031 DNMG434EEM  .500.1875.0625.2031 DNMG442EEM  .500 .250 .0313.2031 DNMG443EEM  .500 .250 .0469.2031 DNMG432EMU l l .500.1875.0313.2031 DNMG433EMU l l .500.1875.0469.2031 DNMG434EMU  .500.1875.0625.2031 DNMG432ENZ  .500.1875.0313.2031 DNMG433ENZ  .500.1875.0469.2031

Finishing

Medium to Rough Cutting

Finishing

Light to Medium Cutting Light to Medium Cutting Medium Cutting

Medium to Rough Cutting

Finishing

Medium to Rough Cutting

Medium Cutting

Light to Medium Cutting Light to Medium Cutting Medium Cutting

SNMM 90° Square/Negative Rough to Heavy Cutting

SNMN 90° Square/Negative

SNMN432 SNMN433 SNMN434

 .500.1875.0313  .500.1875.0469  .500.1875.0625

Medium to Rough Cutting

SNP R/L 90° Square/Negative Medium to Rough Cutting SNPL432M SNPR432M

Medium Cutting

 .500.1875.0078 .150  .500.1875 .0156 .150

Medium to Rough Cutting Medium to Rough Cutting Medium to Rough Cutting

Medium to Rough Cutting

Medium to Rough Cutting

See next page for negative inserts availbility continued

● : USA stocked item  : worldwide warehouse item (Items in Red are new items)

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S

AC5015S & AC5025S Availabilty - Negative Inserts

TNGA Triangle/Negative

TNP R/L Triangle/Negative

Sumitomo Catalog Number

Sumitomo Catalog Number

Chipbreaker Type

Chipbreaker Type

— TNGA331

l  .375 .1875.0156 .150

TNPL330.5FFX  l .375 .1875.0078 .150 TNPL331FFX  l .375 .1875.0156 .150 TNPL330.5FFY  .375 .1875.0078 .150 TNPL331FFY  .375 .1875.0156 .150 TNPR330.5FFX  l .375 .1875.0078 .150 TNPR331FFX  l .375 .1875.0156 .150 TNPR330.5FFY  .375 .1875.0078 .150 TNPR331FFY l  .375 .1875.0156 .150

TNGG Triangle/Negative

TNGG330.5ESU l l .375 .1875.0078 .150 TNGG331ESU l l .375 .1875.0156 .150 TNGG332ESU l l .375 .1875.0313 .150

Finishing

Finishing

TNMA Triangle/Negative — TNMA331

l  .375 .1875.0156 .150 l  .375 .1875.0313 .150

TNMA332

VNGG 35° Diamond/Negative

TNMG Triangle/Negative

VNGG330ESU VNGG330.5ESU VNGG331ESU VNGG332ESU

l .375 .1875.0039 .150 l .375 .1875.0078 .150 l .375 .1875.0156 .150

Finishing TNMG330.5ESU  l .375 .1875 .0078 .150 TNMG331ESU l l .375 .1875 .0156 .150 TNMG332ESU l l .375 .1875 .0313 .150 TNMG333ESU l  .375 .1875 .0469 .150 TNMG431ESU l l .500 .1875 .0156 .2031 TNMG432ESU l l .500 .1875 .0313 .2031 Finishing TNMG331EEF l l .375 .1875 .0156 .150 TNMG332EEF  .375 .1875 .0313 .150

Finishing

l .375 .1875.0313 .150 VNGG330.5EEF l l .375 .1875.0078 .150 VNGG331EEF l l .375 .1875.0156 .150 VNMG330.5ESU l l .375 .1875.0078 .150 VNMG331ESU l l .375 .1875.0156 .150 VNMG332ESU l l .375 .1875.0313 .150 VNMG330.5EEF l l .375 .1875.0078 .150 VNMG331EEF l l .375 .1875.0156 .150 VNMG332EEF l l .375 .1875.0313 .150 VNMG331EEX l l .375 .1875.0156 .150 VNMG332EEX l l .375 .1875.0313 .150 VNMG331EUP l l .375 .1875.0156 .150 VNMG332EUP l l .375 .1875.0313 .150 VNMG331EGU l l .375 .1875.0156 .150 VNMG332EGU l l .375 .1875.0313 .150 VNMG333EGU l  .375 .1875.0469 .150 VNMG331EEG l  .375 .1875.0156 .150 VNMG332EEG l l .375 .1875.0313 .150 VNMG333EEG l  .375 .1875.0469 .150 VNMG331ENZ  .375 .1875.0156 .150 VNMG332ENZ  .375 .1875.0313 .150

VNMG 35° Diamond/Negative

Finishing

TNMG331EEX l l .375 .1875 .0156 .150 TNMG332EEX l l .375 .1875 .0313 .150 TNMG333EEX  l .375 .1875 .0469 .150 TNMG331EUP l l .375 .1875 .0156 .150 TNMG332EUP l l .375 .1875 .0313 .150 TNMG333EUP l  .375 .1875 .0469 .150 TNMG432EUP l l .500 .1875 .0313 .2031 TNMG331EGU  l .375 .1875 .0156 .150 TNMG332EGU l l .375 .1875 .0313 .150 TNMG333EGU  .375 .1875 .0469 .150 TNMG331EEG  .375 .1875 .0156 .150 TNMG332EEG l l .375 .1875 .0313 .150 TNMG333EEG  l .375 .1875 .0469 .150 TNMG332EEM  .375 .1875 .0313 .150 TNMG333EEM  .375 .1875 .0469 .150 TNMG666EEM  l .750 .375 .0938 .3126 TNMG332EMU l l .375 .1875 .0313 .150 TNMG333EMU  .375 .1875 .0469 .150 TNMG432EMU l l .500 .1875 .0313 .2031 TNMG433EMU l l .500 .1875 .0469 .2031 TNML331EHM  .375 .1875.0156 .150 TNML332EHM  .375 .1875.0313 .150 TNMR331EHM  .375 .1875.0156 .150 TNMR332EHM  .375 .1875.0313 .150

Light to Medium Cutting Light to Medium Cutting Medium Cutting Medium Cutting Medium to Rough Cutting Medium to Rough Cutting

Finishing

Light to Medium Cutting Light to Medium Cutting Medium Cutting Medium Cutting Medium to Rough Cutting

WNMG Trigon/Negative WNGG Trigon/Negative Finishing WNGG431ESU l

.500 .1875.0156.2031

WNMG331ESU l l .375 .1875 .0156 .150 WNMG332ESU l l .375 .1875 .0313 .150 WNMG431ESU l l .500 .1875 .0156 .2031 WNMG432ESU l l .500 .1875 .0313 .2031 WNMG433ESU l l .500 .1875 .0469 .2031 WNMG331EEF  l .375 .1875 .0156 .150 WNMG332EEF l l .375 .1875 .0313 .150 WNMG431EEF l l .500 .1875 .0156 .2031 WNMG432EEF l l .500 .1875 .0313 .2031 WNMG331EEX l l .375 .1875 .0156 .150 WNMG332EEX l l .375 .1875 .0313 .150 WNMG431EEX l l .500 .1875 .0156 .2031 WNMG432EEX l l .500 .1875 .0313 .2031 WNMG433EEX l l .500 .1875 .0469 .2031 WNMG432EUP l l .500 .1875 .0313 .2031 WNMG433EUP  l .500 .1875 .0469 .2031 WNMG431EGU  l .500 .1875 .0156 .2031 WNMG432EGU l l .500 .1875 .0313 .2031 WNMG433EGU l l .500 .1875 .0469 .2031 WNMG332EEG l l .375 .1875 .0313 .150 WNMG333EEG  .375 .1875 .0469 .150 WNMG431EEG l l .500 .1875 .0156 .2031 WNMG432EEG l l .500 .1875 .0313 .2031 WNMG433EEG l l .500 .1875 .0469 .2031 WNMG432EEM l l .500 .1875 .0313 .2031 WNMG433EEM l l .500 .1875 .0469 .2031 WNMG332EMU l l .375 .1875 .0313 .150 WNMG432EMU l l .500 .1875 .0313 .2031 WNMG433EMU l l .500 .1875 .0469 .2031 WNMG431ENZ  .500 .1875 .0156 .2031 WNMG432ENZ  .500 .1875 .0313 .2031 WNMG433ENZ  .500 .1875 .0469 .2031

TNM R/L Triangle/Negative Medium to Rough Cutting

Finishing

Finishing

Light to Medium Cutting

Light to Medium Cutting Medium Cutting

Medium Cutting

Medium to Rough Cutting Medium to Rough Cutting Medium to Rough Cutting

See next page for positive inserts availbility

● : USA stocked item  : worldwide warehouse item (Items in Red are new items)

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S

AC5015S & AC5025S Availabilty - Positive Inserts

CPMT 80° Diamond/ 11° Relief Angle Sumitomo

DCMT 55° Diamond/ 7° Relief Angle Sumitomo

CCGT 80° Diamond/ 7° Relief Angle Sumitomo

Catalog Number

Catalog Number

Catalog Number

CPMT2.51.51ESU  .250 .094 .0156 .110 CPMT2.51.52ESU  .250 .094 .0313 .110 CPMT21.51ESU l l .250 .094 .0156 .110 CPMT21.52ESU l l .250 .094 .0313 .110 CPMT321ESU  .375 .125 .0156.1732 CPMT322ESU  .375 .125 .0313.1732 CPMT32.51ESU l l .375 .156 .0156.1732 CPMT32.52ESU l l .375 .156 .0313.1732

DCMT21.50.5ESU l l .250 .094 .0078 .110 DCMT21.51ESU l l .250 .094 .0156 .110 DCMT21.52ESU l l .250 .094 .0313 .110 DCMT32.50.5ESU l l .375 .156 .0078.1732 DCMT32.51ESU l l .375 .156 .0156.1732 DCMT32.52ESU l l .375 .156 .0313.1732 DCMT21.51EGU l l .250 .094 .0156 .110 DCMT21.52EGU l l .250 .094 .0313 .110 DCMT32.51EGU l l .375 .156 .0156.1732

CCGT03X101LFY  .1378.0551.0039.0748 CCGT03X102LFY  .1378.0551.0078.0748 CCGT03X104LFY  .1378.0551.0156.0748 CCGT04X101LFY  .1693.0709.0039.0906 CCGT04X102LFY  .1693.0709.0078.0906 CCGT04X104LFY  .1693.0709.0156.0906 CCGT03X101RFY  .1693.0551.0039.0748 CCGT03X102RFY  .1378.0551.0078.0748 CCGT03X104RFY  .1378.0551.0156.0748 CCGT04X101RFY  .1693.0709.0039.0906 CCGT04X102RFY  .1693.0709.0078.0906 CCGT04X104RFY  .1693.0709.0156.0906 CCGT21.5.001LFX  .250.0937.0012.1102 CCGT21.50LFX  .250.0937.0039.1102 CCGT21.50.5LFX  .250.0937.0078.1102 CCGT21.51LFX  .250.0937.0156.1102 CCGT32.5.001LFX  .375 .156 .0012.1732 CCGT32.50LFX  .375 .156 .0039.1732 CCGT32.50.5LFX  .375 .156 .0078.1732 CCGT32.51LFX  .375 .156 .0156.1732 CCGT32.52LFX  .375 .156 .0313.1732 CCGT21.5.001RFX  .250.0937.0012.1102 CCGT21.50RFX  .250.0937.0039.1102 CCGT21.50.5RFX  .250.0937.0078.1102 CCGT21.51RFX  .250.0937.0156.1102 CCGT32.5.001RFX  .375 .156 .0012.1732 CCGT32.50RFX  .375 .156 .0039.1732 CCGT32.50.5RFX  .375 .156 .0078.1732 CCGT32.51RFX  .375 .156 .0156.1732 CCGT32.52RFX  .375 .156 .0313.1732 CCGT32.50MESI l l .375 .156 .0039.1732 CCGT32.50.5MESI l l .375 .156 .0078.1732 CCGT32.51MESI l l .375 .156 .0156.1732 CCGT32.52MESI l l .375 .156 .0313.1732

DCGT 55° Diamond/ 7° Relief Angle

DPMT 55° Diamond/ 11° Relief Angle

DCGT21.5.001LFX  l .250 .094 .0012 .110 DCGT21.50LFX  l .250 .094 .0039 .110 DCGT21.50.5LFX  l .250 .094 .0078 .110 DCGT32.5.001LFX  l .375 .156 .0012 .1732 DCGT32.50LFX  l .375 .156 .0039 .1732 DCGT32.50.5LFX  l .375 .156 .0078 .1732 DCGT32.51LFX  l .375 .156 .0156 .1732 DCGT21.5.001LFY  .250 .094 .0012 .110 DCGT21.50LFY  .250 .094 .0039 .110 DCGT21.50.5LFY  .250 .094 .0078 .110 DCGT21.51LFY  .250 .094 .0156 .110 DCGT32.5.001LFY  .375 .156 .0012 .1732 DCGT32.50LFY  .375 .156 .0039 .1732 DCGT32.50.5LFY  .375 .156 .0078 .1732 DCGT32.51LFY  .375 .156 .0156 .1732 DCGT21.5.001LFYS  .250 .094 .0012 .110 DCGT21.50LFYS  .250 .094 .0039 .110 DCGT21.50.5LFYS  .250 .094 .0078 .110 DCGT21.51LFYS  .250 .094 .0156 .110 DCGT32.5.001LFYS  .375 .156 .0012 .1732 DCGT32.50LFYS  .375 .156 .0039 .1732 DCGT32.50.5LFYS  .375 .156 .0078 .1732 DCGT32.51LFYS  .375 .156 .0156 .1732 DCGT21.5.001RFX  l .250 .094 .0012 .110 DCGT21.50RFX  l .250 .094 .0039 .110 DCGT21.50.5RFX  l .250 .094 .0078 .110 DCGT32.5.001RFX  l .375 .156 .0012 .1732 DCGT32.50RFX  l .375 .156 .0039 .1732 DCGT32.50.5RFX  l .375 .156 .0078 .1732 DCGT32.51RFX  .375 .156 .0156 .1732 DCGT21.5.001RFY  .250 .094 .0012 .110 DCGT21.50RFY  .250 .094 .0039 .110 DCGT21.50.5RFY  .250 .094 .0078 .110 DCGT21.51RFY  .250 .094 .0156 .110 DCGT32.5.001RFY l  .375 .156 .0012 .1732 DCGT32.50RFY  .375 .156 .0039 .1732 DCGT32.50.5RFY l  .375 .156 .0078 .1732 DCGT32.51RFY l  .375 .156 .0156 .1732 DCGT21.5.001RFYS  .250 .094 .0012 .110 DCGT21.50RFYS  .250 .094 .0039 .110 DCGT21.50.5RFYS  .250 .094 .0078 .110 DCGT21.51RFYS  .250 .094 .0156 .110 DCGT32.5.001RFYS  .375 .156 .0012 .1732 DCGT32.50RFYS  .375 .156 .0039 .1732 DCGT32.50.5RFYS  .375 .156 .0078 .1732 DCGT32.51RFYS  .375 .156 .0156 .1732 DCGT21.50MEFC  l .250 .094 .0039 .110 DCGT21.50.5MEFC  l .250 .094 .0078 .110 DCGT21.51MEFC l l .250 .094 .0156 .110 DCGT32.50MEFC l l .375 .156 .0039 .1732 DCGT32.50.5MEFC l l .375 .156 .0078 .1732 DCGT32.51MEFC  l .375 .156 .0156 .1732 DCGT21.50MESI l l .250 .094 .0039 .110 DCGT21.50.5MESI l l .250 .094 .0078 .110 DCGT21.51MESI l l .250 .094 .0156 .110 DCGT32.50MESI l l .375 .156 .0039 .1732 DCGT32.50.5MESI l l .375 .156 .0078 .1732 DCGT32.51MESI l l .375 .156 .0156 .1732 DCGT32.52MESI l l .375 .156 .0313 .1732

DPMT21.51ESU l l .250 .094 .0156 .110 DPMT32.51ESU l l .375 .156 .0156 .1732 DPMT32.52ESU l l .375 .156 .0313 .1732

Finishing

RCMX Round/ 7° Relief Angle — RCMX120400 RCMX200600  .787 .250 RPGA Round/ 11° Relief Angle RCMT Round/ 7° Relief Angle — RCMT120400 RCMT200600  .787 .250

 .472 .1875 — .1654

.2559

l l .472.1875 — .1654

.2559

 .315.1252

.1299

RPGA080300 RPGA100400 RPGA120400

—  .394.1875 .1496  .472.1875 .1654

SCGT Square/ 7° Relief Angle

SCGT32.50.5LFX  .375 .156 .0078.1732 SCGT32.51LFX  .375 .156 .0156.1732 SCGT431LFX  .500.1875.0156.2165 SCGT32.50.5RFX  .375 .156 .0078.1732 SCGT32.51RFX  .375 .156 .0156.1732 SCGT431RFX  .500.1875.0156.2165 SCMT Square/ 7° Relief Angle Finishing SCMT32.51ESU l l .375 .156 .0156.1732 SCMT32.52ESU l l .375 .156 .0313.1732

CCMT 80° Diamond/ 7° Relief Angle

CCMT21.50.5ESU l l .250 .094 .0078 .110 CCMT21.51ESU l l .250 .094 .0156 .110 CCMT21.52ESU l l .250 .094 .0313 .110 CCMT32.50.5ESU l l .375 .156 .0078.1732 CCMT32.51ESU l l .375 .156 .0156.1732 CCMT32.52ESU l l .375 .156 .0313.1732 CCMT431ESU  .500.1875.0156.2165 CCMT432ESU  .500.1875.0313.2165 CCMT21.51EGU l l .250 .094 .0156 .110 CCMT21.52EGU l l .250 .094 .0313 .110 CCMT32.51EGU l .375 .156 .0156.1732 CCMT32.52EGU l .375 .156 .0313.1732

SPG 90° Square/ 11° Relief Angle

 .375 .125 .0313  l .500 .125 .0156 l l .500 .125 .0313

SPG322 SPG421 SPG422

SPMN 90° Square/ 11° Relief Angle

 .500 .125 .0313  .500 .125 .0469  .625 .125 .0313

SPMN422 SPMN423 SPMN532

TBGT Triangular/ 5° Relief Angle

CPGT 80° Diamond/ 11° Relief Angle

TBGT520.5LFX l  .156.0625.0078 .090 TBGT521LFX l  .156.0625.0156 .090 TBGT520LFY  .156.0625.0039 .090 TBGT520.5LFY  .156.0625.0078 .090 TBGT521LFY  .156.0625.0156 .090 TBGT520.5RFX l  .156.0625.0078 .090 TBGT521RFX l  .156.0625.0156 .090 TBGT520LFY  .156.0625.0039 .090 TBGT520.5LFY  .156.0625.0078 .090 TBGT521LFY  .156.0625.0156 .090

— CPGT2.51.50.5 l l .3125 .094 .0078 .134 CPGT2.51.51  .3125 .094 .0156 .134 CPGT2.51.52  .3125 .094 .0313 .134 CPGT320.5 l  .375 .125 .0078.1732 CPGT321 l  .375 .125 .0156.1732 CPGT322 l  .375 .125 .0313.1732 CPGT430.5 l  .500 .1875.0078.2165 CPGT431 l  .500 .1875.0156.2165 CPGT432 l  .500 .1875.0313.2165 Finishing CPGT32.50.5ESU l .375 .156 .0078.1732 CPGT32.51ESU l .375 .156 .0156.1732

TCGT Triangular/ 7° Relief Angle

TCGT1.81.50LFX  .219 .094 .0039 .0984 TCGT1.81.50.5LFX  .219 .094 .0078 .0984 TCGT21.50LFX  .250 .094 .0039 .110 TCGT21.50.5LFX  .250 .094 .0078 .110 TCGT1.81.50LFY  .219 .094 .0039 .0984 TCGT1.81.50.5LFY  .219 .094 .0078 .0984 TCGT21.50LFY  .250 .094 .0039 .110 TCGT21.50.5LFY  .250 .094 .0078 .110 TCGT21.51MESI l l .250 .094 .0156 .110 TCGT1.81.50LFX  .219 .094 .0039 .0984 TCGT1.81.50.5LFX  .219 .094 .0078 .0984 TCGT21.50LFX  .250 .094 .0039 .110 TCGT21.50.5LFX  .250 .094 .0078 .110 TCGT1.81.50LFY  .219 .094 .0039 .0984 TCGT1.81.50.5LFY  .219 .094 .0078 .0984 TCGT21.50LFY  .250 .094 .0039 .110 TCGT21.50.5LFY  .250 .094 .0078 .110

● : USA stocked item  : worldwide warehouse item (Items in Red are new items)

See next page for positive inserts availbility continued

New coated grades for Heat Resistant Alloys & Exotic Materials AC5015S/AC5025S TCMT Triangular/ 7° Relief Angle Sumitomo

AC5015S & AC5025S Availabilty - Positive Inserts

TPMN Triangular/ 11° Relief Angle Sumitomo

VCGT 35° Diamond/ 7° Relief Angle Sumitomo

Catalog Number

Catalog Number

Catalog Number VCGT220LFX

 .250 .125 .0156  .250 .125 .0313 l  .375 .125 .0156  .375 .125 .0313  .500 .1875.0313  .500 .1875.0469

 l .250 .125 .0039 .134 VCGT220.5LFX  l .250 .125 .0078 .134 VCGT221LFX  .250 .125 .0156 .134 VCGT220LFY  .250 .125 .0039 .134 VCGT220.5LFY  .250 .125 .0078 .134 VCGT221LFY  .250 .125 .0156 .134 VCGT220RFX  l .250 .125 .0039 .134 VCGT220.5RFX  l .250 .125 .0078 .134 VCGT221RFX  .250 .125 .0156 .134 VCGT220RFY  .250 .125 .0039 .134 VCGT220.5RFY  .250 .125 .0078 .134 VCGT221RFY  .250 .125 .0156 .134 VCGT631MEFC  .1875 .094 .0156 .090 VCGT220MEFC  l .250 .125 .0039 .134 VCGT220.5MEFC  l .250 .125 .0078 .134 VCGT221MEFC  l .250 .125 .0156 .134 VCGT220MESI l l .250 .125 .0039 .134 VCGT220.5MESI l l .250 .125 .0078 .134 VCGT221MESI l l .250 .125 .0156 .134 VCGT222MESI l l .250 .125 .0313 .134 VCGT330MESI l l .375 .1875 .0039 .1732 VCGT330.5MESI l l .375 .1875 .0078 .1732 VCGT331MESI l l .375 .1875 .0156 .1732 VCGT332MESI l l .375 .1875 .0313 .1732

TPMN221 TPMN222 TPMN321 TPMN322 TPMN432 TPMN433

TCMT21.51ESU l l .250 .094 .0156 .110 TCMT21.52ESU l l .250 .094 .0313 .110 TCMT32.51ESU l l .375 .156 .0156.1693 TCMT32.52ESU l l .375 .156 .0313.1693

TPG Triangular/ 11° Relief Angle

TPG221 TPG321 TPG322 TPG432

 .250 .125 .0156 l l .375 .125 .0156 l l .375 .125 .0313 l  .500 .1875 .0313

TPMT Triangular/ 11° Relief Angle

TPMT630.5ESU  .1875 .094 .0078 .090 TPMT631ESU  .1875 .094 .0156 .090 TPMT1.81.50.5ESU  l .219 .094 .0078 .102 TPMT1.81.51ESU  l .219 .094 .0156 .102 TPMT21.50.5ESU l l .250 .094 .0078 .107 TPMT21.51ESU l l .250 .094 .0156 .107 TPMT21.52ESU l l .250 .094 .0313 .107 TPMT220.5ESU  .250 .125 .0078 .130 TPMT221ESU  .250 .125 .0156 .130 TPMT222ESU  .250 .125 .0313 .130 TPMT32.51ESU l l .375 .156 .0156.1693 TPMT32.52ESU l l .375 .156 .0313.1693 TPMT331ESU  .375 .1875.0156.1732 TPMT332ESU  .375 .1875.0313.1732 TPMT221ENF l l .250 .125 .0156 .130 TPMT222ENF l l .250 .125 .0313 .130 TPMT331ENF l l .375 .1875.0156.1693 TPMT332ENF l l .375 .1875.0313.1693  .250 .125 .0039 .134 VBGT220.5LFX  .250 .125 .0078 .134 VBGT221LFX  .250 .125 .0156 .134 VBGT220LFY  .250 .125 .0039 .134 VBGT220.5LFY  .250 .125 .0078 .134 VBGT221LFY  .250 .125 .0156 .134 VBGT22.001LFYS  .250 .125 .0012 .134 VBGT220LFYS  .250 .125 .0039 .134 VBGT220.5LFYS  .250 .125 .0078 .134 VBGT221LFYS  .250 .125 .0156 .134 VBGT222LFYS  .250 .125 .0313 .134 VBGT220RFX  .250 .125 .0039 .134 VBGT220.5RFX  .250 .125 .0078 .134 VBGT221RFX  .250 .125 .0156 .134 VBGT220RFY  .250 .125 .0039 .134 VBGT220.5RFY  .250 .125 .0078 .134 VBGT221RFY  .250 .125 .0156 .134 VBGT22.001RFYS  .250 .125 .0012 .134 VBGT220RFYS  .250 .125 .0039 .134 VBGT220.5RFYS  .250 .125 .0078 .134 VBGT221RFYS  .250 .125 .0156 .134 VBGT222RFYS  .250 .125 .0313 .134 VBGT220MESI l l .250 .125 .0039 .134 VBGT220.5MESI l l .250 .125 .0078 .134 VBGT221MESI l l .250 .125 .0156 .134 VBGT222MESI  l .250 .125 .0313 .134 VBGT330MESI l l .375 .1875.0039.1732 VBGT330.5MESI l l .375 .1875.0078.1732 VBGT331MESI l l .375 .1875.0156.1732 VBGT332MESI l l .375 .1875.0313.1732

TPGG Triangular/ 11° Relief Angle Finishing to Light Cutting TPGG221L TPGG331L TPGA Triangular/ 11° Relief Angle — TPGA221 TPGA331 TPGT Triangular/ 11° Relief Angle

 .250 .125 .0156 .130  .375.1875.0156.1693

l  .250 .125 .0156 .130  .375.1875.0156.1693

TPGT630.5LFX l l .1875 .094 .0078 .090 TPGT631LFX l l .1875 .094 .0156 .090 TPGT21.50.5LFX l  .250 .094 .0078 .110 TPGT21.51LFX l l .250 .094 .0156 .110 TPGT21.52LFX l  .250 .094 .0313 .110 TPGT220.5LFX l l .250 .125 .0078 .130 TPGT221LFX  l .250 .125 .0156 .130 TPGT222LFX  l .250 .125 .0313 .130 TPGT321LFX  .375 .125 .0156.1732 TPGT322LFX  .375 .125 .0313.1732 TPGT63.001LFY  l .1875 .094 .0012 .090 TPGT630LFY  l .1875 .094 .0039 .090 TPGT630.5LFY  .1875 .094 .0078 .090 TPGT631LFY  .1875 .094 .0156 .090 TPGT1.81.50LFY  .2189 .094 .0039 .110 TPGT1.81.50.5LFY  .2189 .094 .0078 .110 TPGT1.81.51LFY  .2189 .094 .0156 .110 TPGT22.001LFY  .250 .125 .0012 .130 TPGT220LFY  .250 .125 .0039 .130 TPGT220.5LFY  .250 .125 .0078 .130 TPGT221LFY  .250 .125 .0156 .130 TPGT222LFY  .250 .125 .0313 .130 TPGT320.5LFY  .375 .125 .0078.1732 TPGT321LFY  .375 .125 .0156.1732 TPGT322LFY  .375 .125 .0313.1732 TPGT630.5RFX l l .1875 .094 .0078 .090 TPGT631RFX l l .1875 .094 .0156 .090 TPGT21.50.5RFX l  .250 .094 .0078 .110 TPGT21.51RFX l  .250 .094 .0156 .110 TPGT21.52RFX l  .250 .094 .0313 .110 TPGT220.5RFX  l .250 .125 .0078 .130 TPGT221RFX  l .250 .125 .0156 .130 TPGT222RFX  l .250 .125 .0313 .130 TPGT321RFX  .375 .125 .0156.1732 TPGT322RFX  .375 .125 .0313.1732 TPGT63.001RFY  l .1875 .094 .0012 .090 TPGT630RFY  l .1875 .094 .0039 .090 TPGT630.5RFY  .1875 .094 .0078 .090 TPGT631RFY  .1875 .094 .0156 .090 TPGT1.81.50RFY  .2189 .094 .0039 .110 TPGT1.81.50.5RFY  .2189 .094 .0078 .110 TPGT1.81.51RFY  .2189 .094 .0156 .110 TPGT22.001RFY  .250 .125 .0012 .130 TPGT220RFY  .250 .125 .0039 .130 TPGT220.5RFY  .250 .125 .0078 .130 TPGT221RFY  .250 .125 .0156 .130 TPGT222RFY  .250 .125 .0313 .130 TPGT320.5RFY  .375 .125 .0078.1732 TPGT321RFY  .375 .125 .0156.1732 TPGT322RFY  .375 .125 .0313.1732 TPGT220.5MEFC  l .250 .125 .0078 .130 TPGT221MEFC  l .250 .125 .0156 .130

VCMT 35° Diamond/ 7° Relief Angle

VCGT631ESU  .1875 .094 .0156 .090 VCMT220.5ESU  .250 .125 .0078 .134 VCMT221ESU  .250 .125 .0156 .134 VCMT222ESU  .250 .125 .0313 .134 VCMT331ESU l l .375 .1875.0156.1732 VCMT332ESU l l .375 .1875.0313.1732 VCMT331EGU l l .375 .1875.0156.1732 VCMT332EGU l l .375 .1875.0313.1732

VBGT 35° Diamond/ 5° Relief Angle VBGT220LFX

Medium Cutting

WBGT 80° Trigon/ 5° Relief Angle

WBGT520.5LFX l  .156 .0625.0078 .090 WBGT521LFX l  .156 .0625.0156 .090 WBGT630.5LFX  .1875 .094 .0078 .090 WBGT631LFX  .1875 .094 .0156 .090 WBGT520.5LFY  .156 .0625.0078 .090 WBGT521LFY  .156 .0625.0156 .090 WBGT520.5RFX  .156 .0625.0078 .090 WBGT521RFX  .156 .0625.0156 .090 WBGT630.5RFX  .1875 .094 .0078 .090 WBGT631RFX  .1875 .094 .0156 .090 WBGT520.5RFY  .156 .0625.0078 .090 WBGT521RFY  .156 .0625.0156 .090

● : USA stocked item  : worldwide warehouse item (Items in Red are new items)

VBMT 35° Diamond/ 5° Relief Angle

VBMT220.5ESU  .250 .125 .0078 .134 VBMT221ESU l l .250 .125 .0156 .134 VBMT222ESU l l .250 .125 .0313 .134 VBMT331ESU l l .375 .1875.0156.1732 VBMT332ESU l l .375 .1875.0313.1732 VBMT221EGU l l .250 .125 .0156 .134 VBMT222EGU l l .250 .125 .0313 .134 VBMT331EGU l l .375 .1875.0156.1732 VBMT332EGU l l .375 .1875.0313.1732

Finishing to Light Cutting

Sumitomo Electric Carbide, Inc. AC5000S P roduct P age

Sumitomo Electric Carbide, Inc. Headquarters 1001 Business Center Drive Mount Prospect, IL 60056-2181 P.O. Box 545, Mt. Prospect, IL 60056-0545

Detroit Branch

14496 Sheldon Road #230 Plymouth, MI 48170 Phone: (800) 239-5177 Phone: (734) 451-0200 Fax: (734) 451-5338

Phone: (800) 950-5202 Phone: (847) 635-0044 Fax: (847) 635-9335 http://www.sumicarbide.com Sumitomo Electric Carbide, Inc. Headquarters 1001 Business Center Drive Mount Prospect, IL 60056-2181

Sumitomo Electric Tool Engineering Center 5637 S. Westridge Drive New Berlin, WI 53151 Phone: (800) 950-5202 Sumitomo Electric Carbide, Inc. - Americas Tool EngineeringCenter Phone: (800) 950-5202 Ph ne: (847) 635-0044 Fax: (847) 635-7866

Huntsville Branch

6700 Odyssey Drive Suite 211 Huntsville, AL 35806 Phone: (256) 971-1203 Fax: (256) 971-1205 Sumitomo Carbide Canada, Inc. 150 Research Lane Unit #210 Guelph, Ontario N G 4T2 Canada

595 S. Emerson Avenue Suite 100 Greenwood, IN 46143 Phone: (317) 859-1601 5637 S. Westridge Drive New Berlin, WI 53151 (800) 950-5202

Indiana Branch

Phone: (519) 265-6050 Phone: (844) 211-6050

Torrance Branch 21241 South Western Avenue Suite 120 Torrance, CA 90501 Phone: (800) 950-5202 Fax: (310) 782-0211 i o o Carbide Canada, Inc. 150 Research Lane Unit #210 Guelph, O tario N1G 4T2 Can d Phone: (519) 265-6050 (844) 211-6050 21241 South Western Avenue Suite 120 Torrance, CA 90501 Phone: (800) 950-5202 Fax: (310) 782-0211 595 S. Emerson Avenue Suite 100 Greenwood, IN 46143 Phone: (317) 859-1601 West Coast Branch - Torrance Sumitom Cartomo Hardmetal Mexico (SHMM) Av. Agauascalientes Sur #2625 Fracc. Jardines de las Fuentes Aguascalientes, AGS Mexico C.P. 20278 Phone: 011-52-449-993-2740 Fax: 011-52-449-993-2753 www.sumicarbide.com Indiana Branch - Greenwood

Detroit Branch

14496 Sheldon Road #230 Plymouth, MI 48170 Phone: (800) 239-5177 Phone: (734) 451-0200 Fax: (734) 451-5338

Huntsville Branch

6700 Odyssey Drive Suite 211 Huntsville, AL 35806 Phone: (256) 971-1203 Fax: (256) 971-1205

CAT.AC5000SBROCHURE.10/20

CAT.AC5000BROCHURE.10/20

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8

sumicarbide.com

Made with FlippingBook - Online magazine maker