SUPERLINK ARM & SWIVEL A new take on the traditional multi-carb linkage arm. Zinc die-cast with a modern H-beam
POWER BY-PASS VALVES Standard factory power-valve (power by-pass jet), with new fiber-gasket, for Stromberg 48 and 40 carburetors at sea level. Also fits Stromberg 97, 81, LZ and other models.
section for strength without excess weight, and a small feature-line at the bottom edge for a period feel. The counter-sunk stainless steel screw
No. 63 . . . . . 9594K-63 No. 65 . . . . . 9594K-65 No. 67 . . . . . 9594K-67 No. 69 . . . . . 9594K-69 No. 71 . . . . . 9594K-71
matches those on the carb and threads directly into the arm. The stainless steel swivel, secured by a small e-clip on the back, has a cross-hole sized for the typical 3/16" diameter linkage rod, secured by a black knurled-tip set-screw. 9091K $16.00 each
Your Choice $13.00 each
ACCELERATOR PUMP ROD FOR 97/48/40
ACCELERATOR PUMP KIT FOR 81 Talk about original. Our Stromberg 81 accelerator pump has the correct 10-finger brass spring-washer and small bore leather seal. The kit includes new springs, retainer, washers, felt gasket and cotter pin. 9630K-81 $26.00 kit
Full accelerator-pump kit for Stromberg 97, 48 and 40 carburetors. Includes new springs, retainer, washers, felt gasket and cotter pin. 9630K $20.00 kit CABLE CHOKE BRACKET A perfect replica - in stainless steel - of the cable-choke mounting bracket that came with ‘49-’53 Fords. This separate bracket (included with our 9510A-C cable-choke carburetor) - mounts off the rear body screw to hold the choke-cable sleeve. 9552K-B $22.00 each
KICKER ASSEMBLY / CABLE CHOCK
A perfect replica - in stainless steel - of the 97 kicker assembly for cable choke (designed for ‘49-53 Fords). A separate bracket - included - mounts off the rear body screw to hold the choke- cable sleeve. 9552K-C $50.00 each
BRASS FLOAT & HINGE PIN Fits 97, 81, 48, 40 and other models too. Made on the original Stromberg tooling. Pressure tested, of course, and supplied with a new float hinge-pin. 9550K $22.00 set
BOWL PLUG GASKETS If your Stromberg is leaking from underneath, these
could be the answer. 9563K $5.00 set
IDLE JETS Not often a problem, but we’ve got them if you need them. They must seal securely in the casting on that angled seat just below the cross- hole at the top end. 9542K $17.00 pair 1933-38 STROMBERG NEEDLE & SEAT KIT This is the correct replacement. 3 piece kit. 40-9564 $16.00 kit
MAIN JETS Standard factory main jets for Stromberg 48 and 40 carburetors at sea level. Two jets. Installs with Genuine Stromberg jet wrench - 9071K.
S-JET INLET VALVE The Genuine Stromberg twin-ball S-jet is the ‘next generation’ needle and seat. It’s designed to eject dirt particles and improve high- speed running and, unlike many so-called viton-tipped needle valve, it won’t stick or melt in today’s corrosive new gas formulas. Comes with a new fiber washer. Fits Stromberg 97, 48, 81 and 40. 9564K $17.00 each
0.035 inch . . 9533K-35 0.041 inch . . . . 9533K-41 0.043 inch . . 9533K-43 0.045 inch . . 9533K-45 0.048 inch . . 9533K-48 Your Choice $10.00 pair
123
Made with FlippingBook - Online magazine maker