Modular Quick-Change System PSZ Turn PSZ TGAR - Round Edged Grooving Insert / TTE Insert
l =USA Stocked item = World Wide Warehouse Item
Fig 1
± 0.025
GAN
CW
* For the holder, SUMIBO SUMIDIA Coated Ca Carbide Coated C Coated C Cermet
Cutting Edge GAN
Grade
± 0.025
GAN
RE
Coated Carbide AC530U
CW
15° 25° 15° 15° 10°
Honing
IC
H1
Sharp Edge
Carbide
RE
Coated Cermet T3000Z Coated Cermet T2500Z
Honing Honing
T1500A
Sharp Edge
Cermet
SUMIBORON BN2000
Negative Land 5°
DA2200
15°
Sharp Edge
SUMIDIA
S
Figure shows right hand (R) tool.
* For the rake angle when tted on the holder, refer to page F44.
S
Figure shows right hand (R) tool.
(
Coated Carbide /
Cermet /
Carbide)
Round Edged Grooving Insert
Dimensions ( mm )
AC530U H1 T2500Z T3000Z Width of Cut CW R R R R
Maximum Depth of Cut
Maximum Groove Depth CDX
Nose Radius RE
Inscribed Circle IC
Thickness
*Group No.
Cat. No.
Fig
Internal Diameter
O.D.
S
2 1
1.00 2.0
1.7
2.5
0.50 12.70 4.76
TGAR4050R TGAR4075R TGAR4100R TGAR4125R TGAR4150R TGAR4200R
1 1 1 1 1
1.50 2.00 2.50 3.00 4.00
0.75 1.00 1.25 1.50 2.00
3
3.5
2.5
3.9
12.70 4.76
4
5.0
2.5
5.4
12.70 4.76
*Select applicable inserts for the holders by using matching group numbers.
TTE inserts fits on PSZ - TGAR Holders
Fig 2 (Threading)
11°
PNA
PDX
RE
IC
S
TTE Insert (
DLC Coating )
Coated Carbide /
Cermet /
Dimensions ( mm )
Thread Ridge Angle
Nose Radius
X Direction
Max Depth of Cut
Inscribed Circle
Pitch
Thickness Applicable Holder
Pcs/ Pack
*Group No.
Cat. No.
Fig
S
Threads/Inch RE PDX CDX PNA IC
mm
2 2 2 2 2 2
TTER36002075 0.20 ~ 0.75 80 ~ 32 0.05 0.55 TTER36005125 0.50 ~ 1.25 56 ~ 20 0.05 1.00
0.65 1.30 1.80 2.40 1.50 2.40
60 9.525 3.18 60 9.525 3.18 60 9.525 3.18 60 9.525 3.18 55 9.525 3.18 55 9.525 3.18
1.00 ~ 1.50 24 ~ 16 0.10 1.30 1.50 ~ 3.00 16 ~ 8 0.20 1.70
TTER3601015 TTER3601530 TTER3554816 TTER3552008
GWC 1 10
48 ~ 16 0.05 1.00 20 ~ 8 0.10 1.50
*Select applicable inserts for the holders by using matching group numbers.
Parameters are for the inserts on page 10
Recommended Cutting Conditions Work Material P General Steel
M Stainless Steel
S Exotic Alloy N Non-ferrous Metal H Hardened Steel
Insert Grade H1 DA2200 BN2000 Cutting Speed v c (SFM) 160 to 650 330 to 600 330 to 600160 to 650160 to 650260 to 500260 to 400 65 to 265650 to 1000650 to 1000 260 to 400 Feed Rate f (IPR) .001 to .004 .002 to .004 .002 to .003 .001 to .004.001 to .004.002 to .003.002 to .003.0004 to .0012.002 to .006.002 to .006 .001 to .003 AC530U T2500Z/T3000Z T1500A AC5015/AC5025S AC530U T2500Z/T3000Z T1500A AC5015/AC5025S ● Ordering TGA Type Special Inserts Use the "Special Grooving Insert Request Form" when ordering special inserts (with different shapes, widths of cut, and cutting edge lengths). Make a copy of the form, fill it out and send it to a Sumitomo Electric Carbide, Inc. Sales Representative or distributor.
11
Made with FlippingBook flipbook maker