Why Do I Need Water Treatment? The VistaBrite is a highly specialized filtration system that reduces the contaminants found in water that can negatively impact the finish of instruments processed in instrument washers. High TDS (total dissolved solids), high levels of chlorides and elevated hardness can leave spots and damage expensive instruments. Elevated chlorides in water (usually 50 mg/l or more) at high temperatures are particularly damaging causing moderate-to-severe corrosion that actually pits instrument surfaces leaving orange, red and/or brown spots and greatly shortens their useful life. Reduction of these contaminants also greatly reduces spotting and the maintenance required to keep the internal surfaces and working parts of instrument washers clean. How It Works Water enters the system and is first filtered by the PreFilter to remove small sediment and water treatment chemicals like chlorine. The water then moves through the Hyperfiltration membrane where the TDS is reduced by as much as 95%. The level of contaminant reduction is totally dependent upon the 1) input water pressure, 2) contamination level and
3) input water temperature. Higher input water pressure results in higher output water quality and pressure. The water made by VistaBrite can then be used for all cycles. Installation The VistaBrite has been designed to fit in the base cabinet of most sterilization centers. The system is board-mounted and can hang on the inside of a cabinet wall. Alternatively, it can be mounted on drawer slides so the system can be pulled out for service and filter changes. The slides and additional mounting boards should be obtained through your local dealer. The treated water storage tank can stand upright or can be placed on its side using the plastic tank support included with each system. The VistaBrite can also be placed in an equipment room or other remote location as needed. The line running from the storage tank to the instrument washer can be up to 50 feet. However, will cause a slight reduction in water pressure and flow. Additional tubing can be purchased. See your dealer for a good quality LLDPE or similar 3 / 8 ” O.D. tubing.
Visit www.scican.com or call us toll-free for more information today.
90%
Average TDS Rejection Rate *
Condition
Minimum Maximum
Inlet Pressure
40 psi (2.76 bar)
80 psi (5.52 bar)
I
Inlet Temperature
40°F (4.44°C)
100°F (37.78°C)
Red 1/4”
Hot In
Inlet TDS
50 mg/l
2,000 mg/l ^
Blue 1/4”
I
Cold In
psi
Inlet Hardness
0 mg/l (0 grains)
171 mg/l (10 grains) #
WIKA
Natural 1/4”
I
psi
Inlet Iron
0 mg/l
0.1 mg/l
WIKA
Inlet Manganese
0 mg/l
0.05 mg/l
Inlet pH
4
10
Inlet Turbidity
0
1 NTU
* Pressure dependent ^ Milligrams per liter (mg/l) is equivalent to parts per million (ppm) # Water should be softened if above 10 grains per gallon 1440 Don Mills Road, Toronto ON M3B 3P9
Cold Hose
Natural 3/8”
Black 1/4”
Hot Hose
Drain
Spare Parts
R4151
Replacement Carbon Prefilter
R4155
Replacement Hyperfiltration Filter
S9117
TDS/Temp Meter- Hand Held w/ Case
1440 Don Mills Road, Toronto ON M3B 3P9
www.scican.com USA • SciCan, Inc. • 701 Technology Drive • Canonsburg • Pennsylvania • 15317 Phone (724) 820-1600 • Toll free 1-800 572-1211 • Fax (724) 820-1479 • uscustomerservice@scican.com Canada • SciCan Ltd. • 1440 Don Mills Road • Toronto • Ontario • M3B 3P9 Pnone (416) 445-1600 • Toll free 1-800-667-7733 • Fax (416) 445-2727 • custservice.ca@scican.com
Your Infection Control Specialist is a trademark of SciCan Ltd., VistaBrite and Thermoblend are trademarks of Vista Research Group, LLC. VistaBrite is manufactured by Vista Research Group, LLC.
Made with FlippingBook flipbook maker