GNDI
GND for Internal (ID) Grooving
Internal
Internal Grooving GNDI
Min. Bore Diameter (DMIN)
Fig 1
DCON
H
CW
LHD
LF
Parts Dimensions (inch / mm )
Holder
Figure shows right hand (R) tool.
Cutting Edge Distance
Min. Bore Diameter
Max. Groove Depth
Stock
Screw Wrench
Overall Length
Seat Size
Diameter Height Head
Applicable Insert
Cat. No.
Fig
R L
N m
DCON H LHD LF WF DMIN CW CDX
GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N20 ○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N3 ○○○ - □□ GC □ N40 ○○ - □□ GC □ N5 ○○○ - □□ GC □ N6 ○○○ - □□
● ● 1.000 .906 1.575 8.000 .623 1.250 ● ● 1.000 .906 1.575 8.000 .623 1.250 ● ● 1.000 .906 1.575 8.000 .748 1.250 ● ● 1.000 .906 1.575 8.000 .748 1.250 ● ● 1.000 .906 1.575 8.000 .748 1.250 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 ● ● 1.250 1.181 1.969 10.000 1.024 1.575 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 ● ● 1.500 1.421 2.362 12.000 1.142 2.000 ● ● 1.500 1.421 2.362 12.000 1.142 2.000
GNDI R/L 162T-25 GNDI R/L 163T-25 GNDI R/L 164T-25 GNDI R/L 165T-25 GNDI R/L 166T-25 GNDI R/L 202T-40 GNDI R/L 203T-40 GNDI R/L 204T-40 GNDI R/L 205T-40 GNDI R/L 206T-40 GNDI R/L 243T-43 GNDI R/L 244T-43 GNDI R/L 245T-43 GNDI R/L 246T-43 GNDI R/L 2532-T206 GNDI R/L 2532-T306 GNDI R/L 2532-T406 GNDI R/L 2532-T506 GNDI R/L 3240-T210 GNDI R/L 3240-T310 GNDI R/L 3240-T410 GNDI R/L 3240-T510 GNDI R/L 4050-T311 GNDI R/L 4050-T411 GNDI R/L 4050-T511 GNDI R/L 4050-T611
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
.250 .250 .250 .250 .250 .400 .400 .400 .400 .400 .430 .430 .430 .430
2 3 4 5 6 2 3 4 5 6 3 4 5 6
BH0516 5.0 LH030
BH0616 6.0 LH040
25 25 25 25 32 32 32 32 40 40 40 40
23 23 23 23 30 30 30 30 38 38 38 38
40 200 16 40 200 16 40 200 19 40 200 19 50 250 26 50 250 26 50 250 26 50 250 26 60 300 31 60 300 31 60 300 31 60 300 31
32 2 32 3 32 4 32 5
6 6 6 6
BH0516 5.0 LH030
40 2 10 40 3 10 40 4 10 40 5 10 50 3 11 50 4 11 50 5 11 50 6 11
BH0616 6.0 LH040
BH0616 6.0 LH040
1 Combine the insert with a holder such that the Seat Sze matches. Refer to page 19-20 for applicable inserts. Not usable with GNDIS inserts.
35
: Worldwide Warehouse Item ●: USA Stocked Item
12 & 13
Recommended Cutting Conditions
N m Recommended Tightening Torque (N·m)
Made with FlippingBook flipbook maker