FG-25Z & FG-50Z ESD OPERATING INSTRUCTIO OPERATING INSTRUCTIONS
ESD PRESET TORQUE SCREWDRIVER SCREWDRIVER
Rev 1.0 (5/20/2025)
Register Your FG Mini ESD Screwdriver Register your Mountz FG screwdriver now to ensuring your product is always up-to-date, along with comprehensive resources. Screwdriver Register your Mountz FG screwdriver now to unlock exclusive benefits! Gain access to timely updates, date, along with comprehensive resources. unlock exclusive benefits! Gain access to timely updates, Stay ahead with our commitment to providing you with the best experience possible. Register today for peace of mind and unparalleled support. Scan the QR to register your product(s). d unparalleled support. Scan the QR to register your product(s). Adjusting the Torque Setting for a Preset Value The FG-25z ESD and FG-50z ESD has no external analyzer or torque sensor. If the tool has not been preset to external adjustment scale and must be preset using a torque analyzer or torque sensor. If the tool has not been preset to a set torque value, then follow the direction the screwdriver. emove the end cap from the screwdriver anti-clockwise direction. key into the adjuster and turn clockwise. Turn hex key clockwise to clockwise to decrease torque. on the Torque Analyzer to confirm the torque setting. Do not adjust torque above or below the recommended torque ranges for the torque screwdriver or torque using a 3mm hexagonal key. adjust the torque setting while the screwdriver is connected to a torque sensor as you can over-torque and damage the sensor. for adjusting the torque setting before using 1. Use a 3mm hexagonal key and remov 2. Insert the 3mm hexagonal key into the adjuster and turn c increase torque and counter-clockwise to decrease torque. 3. Take 10 consistent readings on the To torque above or below the recommended torque ranges analyzer. Tighten end-cap back on using a Note: Do not adjust the torque setting while analyzer or torque sensor as you can over adjustment scale and must be preset using a torque directions clockwise direction. not adjust
Applying Torque 1. Tighten fastener or bolt by applying steady twists. The s axis of the bolt during tightening. When pre 2. The screwdriver will automatically reset itself for the next application. 3. With its unique cam-over design, it's impossible to over The screwdriver will automatically reset itself for the next application.
olt by applying steady twists. The screwdriver should be kept in line with the ightening. When pre-set torque is reached, the screwdriver will 'slip.' in line with the
s impossible to overtighten beyond the preset load.
Calibrating Torque Screwdrivers To calibrate a torque screwdriver, either use a torque analyzer or torque sensor within the range of the torque screwdriver. For a torque screwdriver calibrate torque in "Peak slowly and smoothly. 1. Select a torque tester or torque sensor that covers the torque range of the screwdriver. Connect torque tester or torque sensor using the appropriate adapters as needed. 2. Apply torque clockwise slowly until screwdriver 3. Adjust screwdriver to required torque setting as described above either use a torque analyzer or torque sensor within the range of the torque screwdriver. For Peak" mode with a torque tester or torque sensor. Make sure to apply the to Select a torque tester or torque sensor that covers the torque range of the screwdriver. Connect crewdriver 'slips' and note reading. mode with a torque tester or torque sensor. Make sure to apply the torque Select a torque tester or torque sensor that covers the torque range of the screwdriver. Connect the screwdriver to the
4. Test and repeat adjustment as necessary to obtain 5. Recalibrate torque screwdriver at prescribed intervals. orque setting as described above. Test and repeat adjustment as necessary to obtain the desired torque value. Recalibrate torque screwdriver at prescribed intervals.
SILICON VALLEY HEADQUARTERS 1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292 1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com
1
Maintenance Schedule Like an automobile, torque screwdrivers contain moving parts that require periodic servicing and lubrication.
Period Between Resetting of Torque 5,000 fastening operations. It is acknowledged that some tools may achieve 5,000 operations in a relatively short period of time. Under these circumstances, the user may decide, with the benefit of their experience, to increase the period between calibration intervals. Routine Maintenance After 50,000 operations, strip, clean, and re-grease the spring, bearings, and internal components. Any worn components should be replaced. Note: Any tool that is dismantled during its life must be re-lubricated in accordance with the Mountz recommendations. Do not clean tools by immersing them in a solvent, as this will destroy the internal lubrication and cause the tool's failure. Cleaning Regimen Please note that these tools are not designed to be submerged. Compatible Cleaning Solvents: organic cleaning solvents compatible with Nitrile. Mountz recommends Isopropyl Alcohol. Cleansing procedures involving water and isopropyl alcohol-based solvents are permitted. Testing and Servicing Torque tools go out of calibration with use. Calibrating a torque tool is a fine-tuning process of bringing the tool back within its tolerance. Regular torque calibration of a hand screwdriver ensures accuracy, repeatable tool performance, and adherence to international standards. We recommend a general once a year calibration interval. However, the user's organization must determine suitable intervals based upon equipment performance, application, degree of usage, and management objectives.
Mountz Calibration and Repair Services Mountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate and repair most any tool. Mountz provides rapid service with quality that you can trust as we offer two state-of-the-art calibration lab and repair facilities that can calibrate up to 20,000 lbf.ft. About Mountz Mountz, The Torque Tool Specialists ® , has been a leader in the torque tool industry for more than 60 years. Engineered in the Silicon Valley and serving the globe, Mountz focuses on delivering high-quality torque products, services, and solutions to ensure customers can always proceed with confidence. We are committed to forging a safer world through precision and accuracy and by innovating every day.
Mountz Service Locations
Eastern Service Center 19051 Underwood Rd. Foley, AL 36535 Phone: (251) 943-4125 Fax: (251) 943-4979 Western Service Center 1080 N.11th Street San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733 UK Service Center Pier Copse Courtyard, Milland Lane, Liphook, Hampshire, GU30 7JN, UK Phone: 00 44 1428 741756
www.mountztorque.com
SILICON VALLEY HEADQUARTERS 1080 North 11th Street, San Jose, CA 95112 | Phone: (408) 292-2214 | Fax: (408) 292-2733 | mountztorque.com
2
Page 1 Page 2Made with FlippingBook - Online magazine maker