FASTENERS Rivets & Anchors 11
ANCHORS — HOLLOW WALL Hollow Wall Anchors expand inside the wall cavity to provide a large bearing area for load transfer. Standard hollow wall anchors require drilling a hole for installation. Drive type hollow wall anchors do not require a pre-drilled hole for installation. Use them in standard gypsum drywall, plaster, or paneling. Material: Expander shell-Cold-rolled steel
1
STANDARD HOLLOW WALL ANCHORS
Installation: Standard Hollow Wall Anchors • Drill hole using the specified diameter drill bit • Tap anchor into hole until flush with surface
Hole Size
Wall Thickness
Size
Part No.
922.01.1814 922.01.1812 922.01.1878 922.01.18112 922.01.31612 922.01.3161316 922.01.1412 922.01.141316
1/8 XS
5/16 5/16 5/16 5/16
1/16-1/4 1/8-1/2 5/8-7/8
• Tighten screw while maintaining constant pressure on the anchor to set • Remove screw, install screw through fixture, reinsert screw into anchor body and tighten until snug against base material
1/8 S 1/8 L
1/8 XL 3/16 S 3/16 L
1-1/4 – 1-1/2
3/8 3/8
1/8-1/2
5/8 – 1-3/16
1/4 S 1/4 L
7/16 7/16
1/8-1/2
5/8 – 1-3/16
DRIVE-TYPE HOLLOW WALL ANCHORS
Drive-type Hollow Wall Anchors • Drive anchor into gypsum drywall until head is flush with surface • Tighten screw to set anchor • Remove screw, install screw through fixture, reinsert screw into anchor body and tighten until snug against base material
Size
Wall Thickness
Part No.
922.010.1812 922.181316
1/8 SD 1/8 SLD
1/8-1/2 1/8-3/16
ANCHORS — TOGGLE BOLTS
Round Head Part No.
Mushroom Head Part No.
Screw Size 6-32 x 2 6-32 x 3 6-32 x 4 10-24 x 3 10-24 x 4 10-24 x 5 10-24 x 6 1/4-20 x 3 1/4-20 x 4 1/4-20 x 5 1/4-20 x 6 5/16-18 x 4 5/16-18 x 5 5/16-18 x 6 3/8-16 x 3 3/8-16 x 4 3/8-16 x 5 3/8-16 x 6
Size
Part Number Includes Screw and Wing
924.1.1820 924.1.1830 924.1.1840 924.1.3130 924.1.3140 924.1.3150 924.1.3160 924.1.1430 924.1.1440 924.1.1450 924.1.1460 924.1.5640 924.1.5650 924.1.5660 924.1.3830 924.1.3840 924.1.3850 924.1.3860
924.2.1820 924.2.1830 924.2.1840 924.2.3130 924.2.3140
1/8 x 2 1/8 x 3 1/8 x 4 3/16 x 3 3/16 x 4 3/16 x 5 3/16 x 6 1/4 x 3 1/4 x 4 1/4 x 5 1/4 x 6 5/16 x 4 5/16 x 5 5/16 x 6 3/8 x 3 3/8 x 4 3/8 x 5 3/8 x 6
924.2.1430 924.2.1440
Use in: Block, wallboard, plaster, hollow tile Use with: No other fastener needed Made of: Steel, zinc plated
924.2.1460
To Install: Drill hole completely through wall. Insert bolt through item to be fastened, attach wings,fold wings completely back, then push through hole until wings are against inside wall. Tighten with screwdriver. Original and replacement bolts are equipped with a combo-style head.
ANCHORS — TOGGLE WINGS
Make your own size by ordering wings and any coarse thread machine screw
Screw Size 6-32 10-24 1/4-20 5/16-18 3/8-16 1/2-13
Size
Part No
925.18 925.316 925.14 925.516 925.38 925.12
1/8
3/16
1/4
5/16 3/8
1/2
ANCHORS — PLASTIC TOGGLE
• A one piece anchor that takes screws from #6 through #12
Use in: Wallboard, plaster Use with: Sheet metal screws #6 - #12 Made of: Plastic
Panel Thickness
Hole Size 5/16
Screw Size #6 - #12 #6 - #12 #6 - #12
Part No
0 - 1/4 * 3/8 - 1/2 5/8 - 3/4
924.11.14 924.11.38 924.11.58
5/16 5/16
*Mini style plastic toggle
Copyright © 2025 Winzer 800-527-4126
1-11-11
Made with FlippingBook - Online magazine maker