CUTTING TOOLS 5 Misc Cutting Tools
REAMERS — SPIRAL FLUTE (continued)
HEAVY-DUTY HIGH FLUTE CAR REAMER
Flute Length
Overall Length
Diameter
Part No.
661.18.38 661.18.12 661.18.916 661.18.58 661.18.34 661.18.78 661.18.1
3/8 1/2
2-3/4
4-5/8 5-7/8 5-7/8 6-3/8 6-7/8 6-7/8 6-7/8
• Designed for heavy duty reaming of structural steel assemblies • Tapered at the point for holes out at alignment • 1/2” Shank with 3 flats
4 4 5 5 5
9/16 5/8 3/4
4-1/2
7/8
1
END MILLS — DOUBLE-END, 4-FLUTE, CENTER CUT END MILLS
DOUBLE END 4 FLUTE MILLS
Mill Diameter
Flute Length
Shank Diameter
Part No.
655.04.18 655.04.316 655.04.14 655.04.516 655.04.38 655.04.12 655.04.58 655.04.34 655.04.1
1/8
3/8 1/2 5/8 3/4 3/4
3/8 3/8 3/8 3/8 3/8 1/2 5/8 3/4
3/16
Double-End “Center Cut” End Mills are designed for economical profiling and milling of slots, pockets and where plunge cutting is desired. Multi-flute design produces a finer surface finish on work that has previously been roughed out.
1/4
5/16
3/8 1/2 5/8 3/4
1
1-3/8 1-5/8 1-7/8
• Made from high speed steel • Made in USA
1
1
END MILLS — DOUBLE-END, 2-FLUTE, CENTER CUT END MILLS
6
DOUBLE END 2 FLUTE MILLS
Mill Diameter
Flute Length
Shank Diameter
Part No.
655.02.18 655.02.532 655.02.316 655.02.14 655.02.932 655.02.516 655.02.1132 655.02.38 655.02.1332 655.02.716 655.02.1532 655.02.12 655.02.916 655.02.58 655.02.1116 655.02.34 655.02.78 655.02.1
1/8
3/8 7/16 7/16 1/2 9/16 9/16 9/16 9/16
3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 1/2 1/2 1/2 1/2 5/8 5/8 3/4 3/4 7/8
5/32 3/16
1/4
Double-End Two-Flute End Mills are designed for economical general-purpose milling of keyways, slots and pockets. Two-Flute End Mills are sometimes called “Slot Drills” and are recommended for roughing out slots and deep pockets because their deep flutes are less prone to loading or clogging with chips. Two-Flute End Mills can be used to plunge cut or drill into the work piece.
9/32 5/16 11/32 13/32 7/16 15/32 3/8 9/16 5/8 11/16 1/2
13/16 13/16 13/16 13/16 1-1/8 1-1/8 1-5/16 1-5/16 1-9/16 1-5/8
• Made from high speed steel • Made in USA
3/4 7/8
1
1
END MILLS — ROUGHING END MILLS
ROUGHING MILLS
Mill Diameter
Flute Length
Shank Diameter
No. of Flutes
Overall Length Part No.
655.05.14 655.05.516 655.05.12 655.05.58 655.05.34
1/4
5/8 3/4
3/8 3/8 1/2 5/8 3/4
3 3 4 4 4
2-7/16 2-1/2 3-1/4 3-3/4 3-7/8
5/16
• High Speed Steel • For extremely rapid stock removal • Made in USA
1/2 5/8 3/4
1-1/4 1-5/8 1-5/8
Copyright © 2025 Winzer 800-527-4126
6-5-2
Made with FlippingBook - Online magazine maker