FLUID POWER Weatherhead Hydraulics 6
COLL-O-CRIMP COUPLINGS — 338 P-SERIES
• Typical Application: Air brake hose lines • Compatible Hose: Prefix 897.338. • Pressure: Determined by hose burst pressure • Material: CA360 Brass
Assemble Instructions: 1. Push collar onto hose until bottomed
2. Push insert into hose until step on insert (or hex) is flush with collar Note: Swivel fittings require the use of a mandrel or an assembled adapter to push on the insert for assembly. Adapter can be removed after fitting assembly. Light lubricant may be required to assemble fitting into hose. 3. Check for bottoming by checking collar movement along insert. Hose is bottomed when collar cannot slide along insert 4. Depending on Coll-O-Crimp system, follow recommended operating procedures
• Advantages: A permanent hose end saves time and is easy to assemble. Brass material offers excellent resistance against corrosion. • Assemble With: T-400-1 T-410-1 T-420-1 T-440-1, T-460- T-462- T-440- T-465- T-480-
MALE PIPE RIGID Hose I.D. Pipe Size
A A
Hose Cut-Off Factor
Thread Size
Hole Dia.
Hex E Danfoss No. 9/16 33806P-104 11/16 33806P-106 11/16 33808P-106
A
Part No.
897.550.64 897.550.66 897.550.86 897.550.88
3/8 3/8 1/2 1/2
1/4 3/8 3/8 1/2
1/4-18 3/8-18 3/8-18 1/2-14
1.71 1.72 1.73 1.94
.75 .81 .81
.28 .28 .38 .38
E E
1.00
7/8
33808P-108
MALE PIPE SWIVEL Hose I.D. Pipe Size
Hose Cut-Off Factor
A A
Thread Size
Hole Dia.
Hex E Danfoss No. 9/16 33806P-J06
A
Part No.
897.551.66
3/8
3/8
3/8-18
2.18
.81
.28
E E
AIR BRAKE SWIVEL Hose I.D. ABS Size
Hose Cut-Off Factor
Thread Size
Hole Dia.
Hex F Danfoss No.
A A
A
Part No.
33806P-Y76 897.554.66
3/8 1/2
3/8 3/8
3/4-20 3/4-20
1.38 1.38
1.00 1.00
.28 .28
3/4 3/4
897.554.86
33808P-Y76
F F
ADAPTER ABS Size
Pipe Size
Overall Length
ABS Thread Size
Danfoss No.
Part No.
897.555.66 897.555.68 897.555.86 897.555.88
3/8 3/8 1/2 1/2
3/8 1/2 3/8 1/2
1.18 1.37 1.18 1.37
3/4-20 3/4-20 7/8-20 7/8-20
1390 x 6 x 6 1390 x 6 x 8 1390 x 8 1390 x 8 x 8
7
COLL-O-CRIMP COUPLINGS — E-SERIES
HOSE END SERIES: ‘E’ SERIES
• Typical Application: General Purpose low and medium pressure hydraulics. Use H435 where shock hazard exist • Compatible Hose: H009, H209, H243, H265, H275, H285, H435 and H436 • Pressure: Determined by maximum working pressure of hose size
• Material: AISI/SAE 12L14, carbon steel • Plating: Zinc yellow dichromate finish • Advantages: Wide selection of hose and end configurations allowing for a diverse number of applications where hose compatibility is a problem
SAE 37° (JIC) FEMALE SWIVEL Hose I.D. Tube Size Thread Size A
Hose Cut-Off Factor*
Hex E 7/16 9/16 9/16
Hex F Danfoss No.
Part No.
A
897.121.44 897.121.46 897.121.66 897.121.88
1/4 1/4 1/4 3/8 3/8 3/8 1/2 1/2
7/16-20 9/16-18 5/8-18 3/4-16
1.92 1-1/8 2.06 1.25 2.06 1-1/8 2.45 1-1/2
9/16
04E-604 04E-606 06E-606 08E-608
11/16
3/4 7/8 7/8
3/4 7/8
1/2 5/8 897.121.810 * To determine the correct length of hose, subtract the cut-off factor for each end fitting from the overall length of the assembly. 7/8-14 2.51 1.50 08E-610
E
F
SAE 37° (JIC) MALE RIGID Hose I.D. Tube Size Thread Size
A
Hose Cut-Off Factor*
Hex E
A
Danfoss No.
Part No.
3/8 897.138.66 * To determine the correct length of hose, subtract the cut-off factor for each end fitting from the overall length of the assembly. 3/8 9/16-18 1.92 1.00 5/8 06E-506
E
Copyright © 2025 Winzer 800-527-4126
7-6-5
Made with FlippingBook - Online magazine maker