Prodigi ™ Classic 6-10 (E/G)
Top: Left:
20” (508mm)
• Oven must be installed level. • Oven must be installed on noncombustible surface. • Water supply shut-off valve and back-flow preventer when required by local code. • Hood installation is required. • Drain must not be located directly underneath the appliance.
0” (0mm) 18” (457mm) recommended service access 0” (0mm) Non-combustible surfaces 2” (51mm) combustible surfaces
Right:
CHECK FIRST
CLEARANCE
Bottom: 5-1/8” (130mm) Back: 4” (102mm)
4-5/16” (109mm) optional plumbing kit
Noise emissions Without hood system, a maximum 67 dBA was measured at 3.3 ft (1 m) from unit. With hood system, a maximum 81 dBA was measured at 3.3 ft (1 m) from unit.
Heat of rejection 6-10E
BTU/hr
kW
630
0.18
HEAT: ELECTRIC
NOISE: ELECTRIC
Noise emissions NA
Heat of rejection
6-10G BTU/hr
kW
269
0.08
HEAT: GAS
NOISE: GAS
UL Marked Appliances
Maximum Input BTU/h
Minimum Input BTU/h
Maximum Inlet Pressure Inches WC (kPa)
Minimum Inlet Pressure Inches WC (kPa)
Maximum Fuel Consumption* CFH GPH
Natural Gas
43,000
32,000
14.0 (3.5) 14.0 (3.5)
5.5 (1.1)
45.7
N/A
GAS
Propane 0.5 *Assumes an average heating value for natural gs to be 1050 BTU/SCF and a specific gravity of 0.60. The assumed value for propane gas is 2,500 BTU/SCF, and a specific gravity of 1.53. 43,000 32,000 9.0 (2.8) 19.2
Gas Requirements (gas type must be specified on order) Hook-up: 3/4" NPT
Water requirements (per oven) • Two cold water inlets - drinking quality
Water Quality Standards It is the sole responsibility of the owner/operator/purchaser of this equipment to verify that the incoming water supply is comprehensively tested and, if required, a means of “water treatment” provided that would meet compliance requirements with the published water quality standards shown below. Non- compliance with these minimum standards will potentially damage this equipment and/or components and void the original equipment manufacturer’s warranty. Alto-Shaam recommends using the Alto- Shaam Reverse Osmosis System to properly treat your water.
• One treated water inlet: 3/4” NPT connection. Line pressure 30 psi minimum dynamic and 90 psi maximum static (200– 1000 kPa) at a minimum flow rate of 0.26 gpm (1 L/min). • One untreated water inlet: 3/4” NPT connection. Line pressure 30 psi minimum dynamic and 90 psi maximum static (200–1000 kPa) at a minimum flow rate of 2.64 gpm (10 L/min). Water drain: 1-1/2” (40mm) connection with a vertical vent to extend above the exhaust vent. Materials must withstand temperatures up to 200°F (93°C).
WATER
Inlet Water Requirements
Contaminant Treated Water
Untreated Water
Clearance requirements for water filtration system Do not install a water filtration system behind unit.
Free Chlorine
Less than 0.1 ppm (mg/L)
Less than 0.1 ppm (mg/L)
Hardness
30-70 ppm
30-70 ppm
Chloride
Less than 30 ppm (mg/L)
Less than 30 ppm (mg/L)
pH
7.0 to 8.5
7.0 to 8.5
CLEARANCE
Silica
Less than 12 ppm (mg/L)
Less than 12 ppm (mg/L)
Total Dissolved Solids (tds)
50-125 ppm
50-360 ppm
W164 N9221 Water Street | Menomonee Falls, Wisconsin 53051 | U.S.A. Phone: 262.251.3800 | 800.558.8744 U.S.A./Canada | Fax: 262.251.7067 | alto-shaam.com
CONTACT US
CLS-SPC-0047 2/23 Printed in U.S.A.
Due to ongoing product improvement, specifications are subject to change without notice.
Made with FlippingBook Publishing Software