Important shower tray information It is up to the designer or installer to ensure that the tray and enclosure combination is arranged in such a way that water retention meets the customers needs. » The waste has the capacity to carry away 27L/Min. High powered systems may exceed this. Please check with the manufacturer. » Please ensure that the shower head is not positioned directly over the waste as this may restrict water ow rate. » Please ensure that the colour and size of shower tray are as per your order before installation. » You must inspect the product thoroughly before installation. Fitting the product is acceptance of quality. » The trays are handmade from natural material. Please allow for height variances due to manufacturing tolerances. » For open ended shower screens please consult your installer. » Shower trays must be tted as per the tting instruction. Deviation from the pre installation checks or tting installation will void the guarantee. » When wet, the surface of the majority of shower trays will show an increase in the potential for slipping. This is particularly the case when soap, shampoo, bath oil etc. are used. It is important that designers, installers and users are aware of this. Important Although shower door and enclosure sizes are related to tray sizes it is important to note that most shower trays are tiled down to the rim, often over an ‘up-stand’. The finished installation space may be less than the nominal tray size. MERLYN shower units are made to suit this remaining space.
Tray Finish min-max The Tray Finish applies when fitting a door and a tray. These are the minimum and maximum dimensions that a shower door or enclosure will fit using standard wall profiles. Tray nish
Recess Location Take the measurements after the tray is installed and the walls are tiled.
High
Mid
To nd the correct Tray Finish dimension: In a recess: Measure from the finished, tiled wall to the opposite finished, tiled wall. In a corner: Measure from the finished, tiled wall to the edge of the tray.
Low
Recess Location
Corner Location
Note:
If the wall/walls are leaning in, this will further reduce your Tray Finish.
Adjustment This is the min and max adjustment of the actual enclosure. These are the adjustment dimensions of the actual door excluding the tray. Therefore, these are the dimensions to follow when installing a enclosure in a wetroom application without a tray. The guide below may be helpful in taking measurements to determine the shower door or enclosure size required. Dimensions given in this publication are in millimetres, are approximate and may vary with adjustment. They are subject to change without notice. Please note that when a tray is fitted it is essential that the tray is level before any doors or enclosures are fitted.
Wall Location
Quadrant Location
Bath Screens » MERLYN Bath Screens are not designed to t on baths with stepped fronts, roll top rims or integral soap dishes. » Fitting of screen on baths which have raised head rests or shapes is not recommended. » There must be no items causing obstruction with the seal and bath, as any of the above may cause leaks. » When choosing your Bath Screen, please ensure that if your bath has bath handles, they do not interfere with the bath rim area where your screen will be placed. » When choosing an in-swing or folding Bath Screen, please ensure your swing area is not interfering with any brassware or internal shower features. Similarly, when choosing an out–swing, please ensure the out-swing area is free from any obstructions. » It is recommended the shower head position is situated on the same wall to which the Bath Screen is xed and in the centre of the shower area.
UKCA, CE & EN Information
The manufacturer is legally responsible for ensuring that the product conforms to the requirements of both directives. The European Commission thus refers to the CE marking as a “Passport” which allows products to be freely circulated within the EU single market. The UKCA marking allows products to move freely within Great Britain. Often consumers will consider the UKCA and CE markings on a product as an indication of conformance to laid down minimum standards and therefore, a minimum level of safety which other products may lack. Both markings are often seen by consumers as a “Symbol of Safety.”
The UKCA (UK Conformity Assessment) mark on MERLYN enclosures is the new standard marking for products on the market in Great Britain (England, Wales and Scotland). It is a declaration that the product complies with GB designated standards. The CE markings on MERLYN enclosures is a declaration that the product complies with the essential requirements of the relevant European health, safety and environmental protection legislation. EU and GB legislation requires manufacturers to display either the UKCA mark for Great Britain and a CE mark for the EU and Northern Ireland on their product or packaging. It is an offence to place a product on the relevant market without a UKCA for Great Britain or CE marking for the EU market.
EU also including Northern Ireland Mark
Manufacturer: Merlyn Industries Limited, Unit 8,Purcellsinch Ind. Estate, Kilkenny, Ireland, R95 HP71 .
UK Distributor: Merlyn (a division of NGH L ), Ladyfield House, Station Rd, Wilmslow, Cheshire, SK9 1BU.
19 UKCA DOP: UKCATZ1.1 CE DOP: CETZ1.1 Product Code here (MER13) PH EN 14428 CA/IR/DA
Great Britain Mark
Manufacturer: Merlyn Industries Limited, Unit 8,Purcellsinch Ind. Estate, Kilkenny, Ireland, R95 HP71 .
UK Distributor: Merlyn (a division of NGH L ), Ladyfield House, Station Rd, Wilmslow, Cheshire, SK9 1BU.
MERLYN invests heavily in its product development and as such guarantees that its glass fully complies with regulations and is manufactured in accordance with BS EN 14428. The rigorous testing of the glass ensures that the endurance, stability and water retention criteria meet high industry standards.
19 UKCA DOP: UKCATZ1.1 CE DOP: CETZ1.1 Product Code here (MER13) PH EN 14428 CA/IR/DA
New GB, EU and NI label
ISO Certi cation
MERLYN has implemented an Integrated Management System comprising of Quality Management, Environmental Management and Occupational Health and Safety Management. An Integrated Management System ensures the seamless integration of several different standards into a common system that meets the requirements of each of these standards. These certifications are proof of MERLYN’s credibility but also to instil confidence in our potential consumers that MERLYN will keep its promises.
Brochure Recycling
Please be aware our cover is non recyclable. Remove cover before recycling the internal pages.
25
Made with FlippingBook - PDF hosting