WaveMill WEZ Endmill Type - 11mm Insert
Steel
Stainless Steel
Cast Iron
Non-Ferrous Metal
Aluminum Alloy
Exotic Alloy
Insert
Dimensions (inch " / mm )
Grade
Coated Carbide Carbide DLC Cermet
High-speed / Light General-purpose
P
K
N
P
Process
P
K
N N
Roughing
K
P
Wiper Facet Length wpr
Nose Radius RE
Cat. No.
Fig
H
● ● ● ● ● ● ● ● ● ● ● ●
● ●
AOMT11T302PEER-G AOMT11T304PEER-G AOMT11T305PEER-G AOMT11T308PEER-G AOMT11T310PEER-G AOMT11T312PEER-G AOMT11T316PEER-G AOMT11T320PEER-G AOMT11T324PEER-G AOMT11T330PEER-G AOMT11T332PEER-G AOMT11T304PEER-H AOMT11T308PEER-H AOMT11T312PEER-H AOMT11T316PEER-H AOET11T302PEER-F AOET11T304PEER-F AOET11T305PEER-F AOET11T308PEER-F AOET11T310PEER-F AOET11T312PEER-F AOET11T316PEER-F AOET11T320PEER-F AOET11T324PEER-F AOET11T330PEER-F AOET11T332PEER-F AOET11T302PEFR-S AOET11T304PEFR-S AOET11T305PEFR-S AOET11T308PEFR-S AOET11T310PEFR-S AOET11T312PEFR-S AOET11T316PEFR-S AOET11T320PEFR-S AOET11T324PEFR-S AOET11T330PEFR-S AOET11T332PEFR-S
.008" / 0.2 .102" / 2.6 1 .016" / 0.4 .110" / 2.8 1 .020" / 0.5 .106" / 2.7 1 .031" / 0.8 .091" / 2.3 1 .039" / 1.0 .083" / 2.1 1 .047" / 1.2 .079" / 2.0 1 .063" / 1.6 .067" / 1.7 1 .079" / 2.0 .051" / 1.3 1 .094" / 2.4 .035" / 0.9 1 .118" / 3.0 .024" / 0.6 1 .126" / 3.2 .024" / 0.6 1 .016" / 0.4 .110" / 2.8 1 .031" / 0.8 .091" / 2.3 1 .047" / 1.2 .079" / 2.0 1 .063" / 1.6 .067" / 1.7 1 .008" / 0.2 .102" / 2.6 1 .016" / 0.4 .110" / 2.8 1 .020" / 0.5 .106" / 2.7 1 .031" / 0.8 .091" / 2.3 1 .039" / 1.0 .083" / 2.1 1 .047" / 1.2 .079" / 2.0 1 .063" / 1.6 .067" / 1.7 1 .079" / 2.0 .051" / 1.3 1 .094" / 2.4 .035" / 0.9 1 .118" / 3.0 .024" / 0.6 1 .126" / 3.2 .024" / 0.6 1 .008" / 0.2 .102" / 2.6 1 .016" / 0.4 .110" / 2.8 1 .020" / 0.5 .106" / 2.7 1 .031" / 0.8 .091" / 2.3 1 .039" / 1.0 .083" / 2.1 1 .047" / 1.2 .079" / 2.0 1 .063" / 1.6 .067" / 1.7 1 .079" / 2.0 .051" / 1.3 1 .094" / 2.4 .035" / 0.9 1 .118" / 3.0 .024" / 0.6 1 .126" / 3.2 .024" / 0.6 1
— — — —
●
● ●
— —
● ● ● ● ● ● ●
●
— —
●
● ●
— —
● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
— —
— —
— —
●
● ●
— —
● ● ● ● ●
F
Fig 1
— — — —
RE
●
● ●
wpr
● ● ● ● ● ● ● ● ● ● ● ● ● ●
— — — — — — — — — — — —
● ●
● ● ● ●
0.504
● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — — ● — — — — — —
0.142
H50
Recommended Cutting Conditions
● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ●
— — — — — — — — — — — — — —
— —
— — — — — — —
—
— — — — — — —
—
— — — — — — —
—
— — — — — — —
—
— — — — — — —
—
— — — — — — —
—
— — — — — — —
—
— — — — — — — — — — — — — —
— —
● USA stocked item « : worldwide warehouse item — : Can not make -L: Low Cutting Force, -G: General-purpose, -H: Strong Edge, -F: Medium Finishing, -S: Non-ferrous metals.
＊ When mounting inserts with nose radius of 3.0 or above, modification of the body is required.
Precautions for Mounting Inserts
Gap
(1) Clean the mounting seat surface and contact parts. (2) While pressing the insert solidly against the seat surface,tighten the screws with the included wrench. (3) Apply Anti-seize paste to the screws and tighten at the recommended torque. (4) After tightening, check that there are no gaps on the seat surface.
Modify this edge.
Reworking guidelines Nose radius = 3.0: C1 (AOMT11T330PEER) Nose radius = 3.2: C1 (AOMT11T332PEER) Standard: R1.
Wrench
Insert
Body
Gap
H57
Made with FlippingBook Ebook Creator