SEC-Goal Mill GFV5000 Type
Cast Iron
DCSFMS DCB KWW
DCSFMS DCB KWW
DCSFMS
ø101.6
DCB
KWW
CBDP
LF CBDP
CBDP
LF
LF
DC
DC
DC
H
Body
Dimensions (inch)
Effective Cutting Diamater
Number of Teeth
Dia. DC
Boss DCSFMS
Height LF
Bore Dia. DCB
Keyway Width KWW
Keyway Depth KDP
Mounting Depth CBDP
Cat. No.
Stock
Fig
Roughing
Wiper
● 3.000 2.900 2.000 1.000 0.375 0.220 1.060 ● 4.000 3.380 2.000 1.500 0.625 0.385 1.060 ● 6.000 4.880 2.500 2.000 0.761 0.438 1.000 ● 8.000 6.040 2.500 2.500 1.00 0.560 1.595
GFV53000R GFV54000R GFV56000R GFV58000R
6
2 2 4 4
2.352 1 3.342 1 5.342 2 7.342 3
10 12 20
Inserts are sold separately. Left handed cutters are made to order. Insert & Hardware ● USA stocked item
H218
Application Examples
Dimensions (inch)
R
W
T
90°
L
Dimensions (inch)
Catalog No.
Insert Screw*
Insert Wrench
Stock
L
W T R
● ● ● ●
LNGX160516PNFN-W-K244L9 LNGX160516PNFN-W-K246L9 LNGX160516PNFN-W-SN2100K LNGX130516PNTN-W-BN7000**
0.625
0.375 0.187 0.063 BFTX03588
TTX15W
0.500
*Torque specifications for insert screw= 26.5 in/lbs.
**Insert only for use with Special Wiper Cartridge, see below
Micro Adjustment: • Check each of the fixed pocket milling inserts to find the one at the highest setting. • Load the wiper cartridges into the face mill body and torque the cartridge mount screw • Adjust the wiper cartridge using the axial adjustment screw so that it is .0010” ~ .0012” above the highest fixed pocket milling insert
Parts
Axial Adjustment Screw
Cartridge Mount Screw
Wrench for Cartridge Mount Screw
Wrench for Adjustment Screw
Wiper Cartridge*
GFVK5R BX0418
LT15
ED090225E TTX15W
*Insert not included with cartridge
Parts - Wiper Cartridge for CBN Insert Wiper Cartridge for CBN Insert* Adjustment Screw Wrench Insert Screw
Cap Screw Wrench
Wrench (For Adjustment Screw)
Anti-seizure Cream
(For Cartridges)
GFVK5R-13
N m
GFVK5R-13 BTD05F09 TTX15W BFTX03588 3.0 Finishing cartridges do not come assembled with inserts.
LT15
BX0414
TH030 SUMI-P
*Insert not included with cartridge
Recommended Cutting Conditions
Recommended Cutting Conditions - BN7000
ISO Insert Grade K Cast Iron 250HB 800- 1,000 -1,200 0.1- 0.3 -0.5 BN7000 Calculate cutting conditions based on effective no. of teeth. Note Work Material Hardness Cutting Speed v c (m/min) Min. - Optimum - Max. Feed Rate f z (mm/t) Min. - Optimum - Max.
Gray Cast Iron
Ductile Cast Iron
Grade SFM D.O.C.
IPT Grade SFM D.O.C.
IPT
K244L9 450~1150 K246L9 400~650
K244L9 450~800 K246L9 400~600
0.004~0.030 0.004~0.015
0.004~0.030 0.004~0.015
SN2100K 1000~3000 0.010~0.080 0.004~0.010
*Greater depths of cut (up to 4mm) possible if wiper cartridges are removed. NOTE: If the wiper inserts will be indexed without presetting the wiper cartridge heights again, the first preset height should be from 0.001” to 0.002” (0.025 to 0.050 mm) above the highest fixed pocket periphery insert.
H227
Made with FlippingBook Ebook Creator