Flat Bottom Drills MDF-L Type Long Type (External Coolant Supply) Recommended Cutting Conditions
1. A prepared hole with the same diameter is needed for drilling with this tool. 2. A prepared hole with the same diameter is recommended for the cutting conditions.
3. The recommended hole depth is 5 x DC. The depth is measured from the highest point of the hole when drilling in inclined surfaces. 4. This product is a drilling tool. Do not use it for traverse cutting or helical milling.
( v c : Cutting Speed (m/min),
f : Feed Rate (mm/rev))
Dia. DC (mm)
Cutting Conditions
Mild Steel/General Steel (up to 250HB)
Alloy Steel (up to 300HB)
Hardened Steel (up to 50HRC)
Stainless Steel (up to 200HB)
Gray Cast Iron FC250
Ductile Cast Iron FCD450
Aluminum Alloy
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 40
70 - 85 - 100
65 - 75 - 85
90 - 120 - 150
v
c
ø4.0
f 0.06 - 0.08 - 0.10 0.05 - 0.08 - 0.10 0.01 - 0.02 - 0.03 0.01 - 0.02 - 0.03 0.06 - 0.08 - 0.10 0.04 - 0.06 - 0.08 0.06 - 0.08 - 0.10
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65- 75 - 85
90 - 120 - 150
v
c
ø6.0
f 0.05 - 0.10 - 0.15 0.05 - 0.10 - 0.15 0.04 - 0.06 - 0.08 0.03 - 0.04 - 0.05 0.05 - 0.10 - 0.15 0.06 - 0.09 - 0.12 0.05 - 0.10 - 0.15
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65- 75 - 85
90 - 120 - 150
v
c
ø8.0
f 0.10 - 0.15 - 0.20 0.10 - 0.15 - 0.20 0.06 - 0.08 - 0.10 0.04 - 0.06 - 0.08 0.10 - 0.15 - 0.20 0.10 - 0.12 - 0.15 0.10 - 0.15 - 0.20
J
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65 - 75 - 85
90 - 120 - 150
v
c
ø10.0
f 0.15 - 0.20 - 0.25 0.15 - 0.20 - 0.25 0.08 - 0.10 - 0.12 0.06 - 0.08 - 0.10 0.15- 0.20 - 0.25 0.12 - 0.15 - 0.18 0.15 - 0.20 - 0.25
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65 - 75 - 85
90 - 120 - 150
v
c
ø12.0
f 0.20 - 0.25 - 0.30 0.20 - 0.25 - 0.30 0.12 - 0.15 - 0.18 0.08 - 0.10 - 0.12 0.17 - 0.22 - 0.27 0.15 - 0.20 - 0.25 0.20 - 0.25 - 0.30
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65 - 75 - 85
90 - 120 - 150
v
c
ø16.0
f 0.20 - 0.25 - 0.30 0.20 - 0.25 - 0.30 0.14 - 0.17 - 0.20 0.10 - 0.15 - 0.20 0.20 - 0.25 - 0.30 0.20 - 0.25 - 0.30 0.25 - 0.30 - 0.35
60 - 80 - 100
50 - 70 - 90
20 - 30 - 40
20 - 30 - 50
70 - 85 - 100
65 - 75 - 85
90 - 120 - 150
v
c
ø20.0
f 0.25 - 0.30 - 0.35 0.25 - 0.30 - 0.35 0.16 - 0.19 - 0.22 0.15 - 0.20 - 0.25 0.30 - 0.35 - 0.40 0.25 - 0.30 - 0.35 0.35 - 0.40 - 0.45 Min. - Optimum - Max.
J51
Made with FlippingBook Ebook Creator