ELECTRIC TRIM TAB KITS 13
lencomarine.com
Extreme Duty (XD) Performance Trim Tab Kit 12V System / Single Actuator The only single actuator Extreme Duty design offered. This kit is similar to our Heavy Duty Performance series with a thicker, stronger blade for those boaters who run hard in extreme conditions. Boat lengths 20' (6.1 m) to 40' (12.2 m)
Extreme Duty (XD) Performance Trim Tab Kit 12V System / Dual Actuator All the robust features of our single actuator XD series with twice the actuator power for larger, faster boats that don't back away from rough conditions. Boat lengths 23' (7 m) to 50' (15.2 m)
15045-101 Electro-Polished
15046-101 Electro-Polished
Blades are constructed of Electro-Polished 10-gauge (3.4 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with mechanical strain-relief cable seals, welded on stainless steel upper & adjustable lower actuator mounting brackets, 3/8" (9.5 mm) stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed.
Blades are constructed of Electro-Polished 10-gauge (3.4 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 3/8" (9.5 mm) diameter hinge pin. Full transom back plate with mechanical strain-relief cable seals, welded on stainless steel upper & adjustable lower actuator mounting brackets, 3/8" (9.5 mm) stainless steel mounting bolts. 3.75" (9.5 cm) sacrificial anodes installed.
Kit includes: • (2) 10-gauge stainless steel Electro-Polished blades • (2) 15056-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer • Note: Actuator extension harnesses not in kits, must be purchased separately (2 required) See page 42
Kits include: • (2) 10-gauge stainless steel Electro-Polished blades • (4) 15056-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer • Note: Actuator extension harnesses not in kits, must be purchased separately (4 required) See page 42
= Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below.
= Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below.
SHIPPED FULLY ASSEMBLED
SHIPPED FULLY ASSEMBLED
Back Plate Dimensions
Back Plate Dimensions
5" (12.7 cm)
6" (15.2 cm)
8" (20.3 cm)
8" (20.3 cm) 2"
10" (25.4 cm)
10" (25.4 cm)
2" (5.1 cm)
(5.1 cm)
12" (30.5 cm)
14" (35.6 cm)
The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates.
The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates.
Part #
L" X W"
Boat Length Min. Transom Height
Part #
L" X W"
Boat Length Min. Transom Height
15045-101
15046-101 15047-101
17" x 12"
20'–40'
10.5" (26.7 cm)
19" x 14" 24" x 14"
23'–45' 25'–50'
10.5" (26.7 cm) 10.5" (26.7 cm)
Switch kits sold separately See pages 30–32
Switch kits sold separately See pages 30–32
Made with FlippingBook Digital Proposal Creator