AutoBody Master

Technical Manual

INDEX

ABRASIVES

37-38

AEROSOLS

2

BODY FILLER

9-11

BUFFING PADS

35-36

CLEARCOAT

29-34

COATINGS

3

DETAILING SUPPLIES

36

EQUIPMENT ENAMEL

1

FASTENERS

39

FIBERGLASS PRODUCTS

13-14

HARDENERS

19

MASKING

7-8

MISCELLANEOUS

4-6, 8

PRIMERS

20-26

SEALER

27-28

SEAM SEALER

3

SOLVENTS

15-18

Equipment & Implement Enamels Gallon Aerosol Color 6455G 6455 Allis Chalmers Orange 6401G 6401 Black-Gloss 6412G 6412 Black-Low Gloss 6499G 6499 Caterpillar Yellow-New 6487G 6487 Caterpillar Yellow (Old, light) 6435G 6435 Ford Blue 6409G 6409 Ford Gray 6400G 6400 Gray Primer 6431G 6431 Harvester Red 6443G 6443 John Deere Green 6461G 6461 John Deere Yellow 6471G 6471 Massey Ferguson Red 6402G 6402 Red Oxide Primer 6406G 6406 Silver Aluminum 6463G 6463 School Bus Yellow 6476G 6476 White Gloss

Substrates • Fully cured finishes - Sand with 240 - 320 grit paper • Steel - Sand with 80 - 180 grit & prime with Equipment & Implement Primer Mixing

• Reduction is not required. If reduction is preferred, reduce with VM&P Naphtha #5960-1 or 5960-4 (for spray applications) or Mineral Spirits #5950-1 (for brushing or rolling applications) at a 16:1 ratio. Set Up Tech Tip/Needle: 1.4mm to 1.6mm Spot Air Pressure: 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap Coverage 500 sq ft /gallon @ 1 mil Application Product can be rolled, brushed, airless or compressed air sprayed. Apply 2 - 3 coats until sufficient coverage or hiding is achieved. Allow each coat to become hand slick before additional coats are applied. Drying

Dries to the touch in 4 to 6 hours. Pot Life: Indefinite if sealed Physical Data VOC RTS

< 3.5 lb./gallon

Humidity Resistance

Very good Very good

Salt Spray Test

Master Tips Do not apply in direct, hot sunlight. Surface & air temperature should be between 40-90°F during application and dry time. Catalyzation is not recommended.

Page 1

All Purpose Enamels

AB680 AB605 AB600 AB642 AB670

Aluminum Black, Flat Black-Gloss

12 oz 12 oz 12 oz 12 oz 12 oz

Red

White

Engine Enamels AB613 Black

11 oz 11 oz 11 oz 11 oz 11 oz 11 oz

AB607 AB601 AB606 AB625 AB609

Chevy Orange

Ford Blue

Ford Dark Blue Ford/Universal Red

GM Blue

Hi-Temp Paints AB602 Black

11 oz 11 oz

AB604

White

Sandable Primers AB698 Black

12 oz 12 oz 12 oz

AB699 AB694

Gray

Red Oxide

Professional Series 9648 Cut-In Clear

11 oz 12 oz 12 oz 12 oz 12 oz 11 oz 12 oz

9741 9083 9103 9413 9143 9988

Etch & Fill Primer

Flexible Bumper Black Gloss Flexible Bumper Original Black

Flexible Primer

Satin Black Trim Paint Self Etching Primer

Page 2

Rubberized Undercoating - Non-paintable An asphaltic, non-paintable, rubber and wax coating which contains no asbestos fiber and is fast drying. Perfect for undercarriage protection, sound deadening, and wheel well coating. Helps prevent rust. Very flexible and will not crack or peel. Black color.

Part # 7668

Description

Size

Rubberized Undercoat

15.45 oz

Rocker Panel Guard - Paintable An economical gravel guard that offers a tough and flexible paintable coating. The coating’s rubberized base remains pliable to absorb impacts and resists chipping. Use on rocker panels, gravel shields, inner panel sound deadening, trunk panels, chassis, wheel wells, etc. Seals out moisture to protect from the formation of rust and corrosion. Chip resistant and will not pinhole. Do not apply sealer over this product. Black color. Part # Description Size 7658 Rocker Panel Guard - Black 14 oz Rocker Panel Protector - Paintable A premium fast drying permanent textured coating designed for protecting rocker panels and valance panels from stone chips and other road abrasion and weathering. Perfect for rocker panels, gravel shields, fender wells, trunk panels, inner panel protection, etc. It’s super strong adhesion and durability offers a coating that will not flake or chip off, remains flexible and will not crack. Do not apply sealer over this product. Available in 850 ml “schutz” style cans in black or beige. Part # Description Size 7652 Rocker Panel Protector-Black 28.7 fl. oz. 7653 Rocker Panel Protector-Beige 28.7 fl. oz. Seam & Joint Sealers A very flexible seam sealer for all types of auto body sealing. Excellent tooling time after application without the use of solvent. Tooling with solvent will offer an extra slick appearance. Paintable in 30 to 60 minutes after application. Skin time is approximately 10 minutes. Sets to a firm abrasion resistant seal that’s tough

with excellent flexibility. No cracking or peeling. Great for use on cowl seams, floor seams, door skins, wheel house seams, trunk seams, etc.

Description

Size

Part # 7605 7607 7612

Seam & Joint Sealer-Beige Seam & Joint Sealer-Black Seam & Joint Sealer-Clear

10 oz/300ml 10 oz/300ml 10 oz/300ml

Urethane Sealant & Adhesive A one component polyurethane adhesive & sealant for areas that are subjected to mechanical stress, shock, vibrations, and sudden impacts. The moisture cure, non sag system cures through atmospheric moisture to a rubber like adhesive and sealant. The flexibility of the product will not crack. Paintable in 30 minutes. Product also offers filing and patching properties that can be sanded. Excellent adhesion to alu- minum bare metal primed and painted, FRP, SMC, and RIM. Excellent weather resistance. Great for bond- ing roof panels, floor panels, interior and exterior body side moulding and trim.

Description

Size

Part # 7627

Urethane Sealant Adhesive-Black 10.5 oz.

Page 3

Urethane Accelerator Reduces dust free, tack free and tape times. Autobody Master urethane accelerator can be added to urethane coatings such as primers, color coats, and clears when improved curing times are desired. Compatible with all major urethane paint systems. Very concentrated, recommended 1/2 ounce per sprayable quart. Great for cool shop conditions.

Part # 8220

Description

Size Pint

Urethane Accelerator

Weather Strip Adhesive Bonds all types of rubber and vinyl to doors and trunks. Waterproof, flexible and dries fast.

Part # 7001 7008

Description

Size

Weather Strip Adhesive-Amber Weather Strip Adhesive-Black

135 ml 135 ml

Double Sided Tape Premium double sided high density urethane foam tape coated with high temperature and UV resistance acrylic adhesive on both sides. This tape is excellent for bonding heavy moldings and trim with it’s superior holding power.

Part #

Description

Size

AV7682D Double Sided Urethane Tape

1/2” x 60’ 7/8” x 60’ 1/2” x 15’ 7/8” x 15’

AV7683D

Double Sided Urethane Tape Double Sided Urethane Tape Double Sided Urethane Tape

7684 7685

Cut Off Wheels Abrasive reinforced wheels. Cuts all ferrous materials with ease. Disks measure 3” x 1/16” x 3/8”.

Part # 1150

Description

Size

Cut Off Wheels 50/box

3”x1/16”x3/8

Razor Blades Premium quality steel back razor blades. Packaged 100 per safety dispenser.

Description

Type

Part # 1100 1112

#9 Razor Blades 100/box

#9

Heavy-Duty Razor Blades 100/box #12

Page 4

Mixing Cups Economical disposable mixing cups feature 12 different mixing ratios. Transparent plastic with easy to read solvent-resistant printing.

Description Mixing Cups Mixing Cups Mixing Cups Mixing Cups Mixing Cups Lids

Part # 1008 1010 1011 1016 1025 1030

Size

Units/Case

1/2 Pint

100 100 100 100

Quart Quart

Pint

2.5 Quart 5 Quart

50 25

Clean Sheets Non porous sheets for mixing body fillers and putties. Sheets will not absorb resins like cardboard. Disposable tear off sheets gives you a clean mixing surface every time.

Part #

Description

Size

CS100ABM Clean Sheets 100/mix pallet

12” x 12”

Leather Work Gloves Premium suede deer skin palms with reinforced fingertips and a Spandex back for dexterity. Hook & loop wrist closure. Water repellant. Washable.

Part #

Description

Size

AM75M Leather Work Gloves

Medium Large X-Lrg. XX-Lrg.

AM75L

Leather Work Gloves

AM75XL Leather Work Gloves AM75XXL Leather Work Gloves

Head Socks Lightweight and breathable head socks keep dirt, dust and overspray off your head and neck. Sewn-in elastic for a snug fit. One size fits all. Colors vary.

Description

Qty.

Part # 1600

Painter’s head socks

20

Touch-Up Bottles 2 oz. plastic bottles feature a brush cap, mixing marbles and shatter-proof HDPE plastic. Fit on most brands of airbrushes.

Part # 1050

Description

Qty.

Touch-Up Bottles

50

Page 5

Paint Sticks

Part # 1001

Description

Paint Sticks approx. 1000/box

Paint Strainers Fine nylon mesh

Part # 1000

Description

Paint Strainers 1000/box

Spreaders Part #

Description

Size

Qty.

1204

Yellow Spreader

4” 4” 5” 5” 6”

12

1204B Yellow Spreader

100

1205

Yellow Spreader

12

1205B Yellow Spreader

100

1206 1209 1212 1213 1215 1225 1234 1236 1239

Yellow Spreader Body Filler Knife

12

6.5”

1 1

Body Filler Mixing Board Black Squeegee/Spreader Black Squeegee/Spreader Blue Glazing Spreader

12”x12”

3” 5”

12 12 12

2.5” 2.5”

1225B Blue Glazing Spreader

100

Spreader Assortment Spreader Assortment

2.5, 3 & 4” 3, 4 & 6” 1, 2, 3 & 4”

1/ea. 1/ea. 1/ea.

Steel Spreader Assortment

Page 6

Green Machine Glazed Masking Paper Green MG (machine glazed) masking paper. Tested for paint hold out and designed as a masking grade paper. Inexpensive compared to treated or coated papers. Bleed through can occur from urethanes or from over saturation.

Part #

Description

Size ~6” ~12” ~18” ~24” ~36”

G6

Machine-Glaze Green Machine-Glaze Green Machine-Glaze Green Machine-Glaze Green Machine-Glaze Green

G12 G18 G24 G36

Green Polycoated Masking Paper Polycoating seals out solvents for better bleed-through protection.

Part # PG12 PG18 PG36

Description

Size ~12” ~18” ~36”

12” Green Polycoat 18” Green Polycoat 36” Green Polycoat

Blue Polycoated Masking Paper Blue poly-coated masking consisting of a 30# basis recycled newsprint with 6 to 7 pounds of poly applied. The poly-coating provides maximum hold out for no bleed through protection. Sold in 700' rolls.

Part #

Description

Size ~12” ~18” ~36”

B12 B18 B36

12” Blue Polycoat 18” Blue Polycoat 36” Blue Polycoat

White Urethane Grade Masking Paper White #24 basis flouro-chemically treated masking paper. Flouro-Chemical treating gives this paper a urethane resistant barrier. Light basis weight makes it ideal for cornering and other intricate masking applications. Sold in 750' rolls.

Part #

Description

Size ~12” ~18” ~36”

W12 W18 W36

12” White Coated 18” White Coated 36” White Coated

Plastic Sheeting: Extremely low static. Good stretch and tear strength. Quickly mask off vehicles, cutting away repair area for the fastest masking job available. EZ Dispenser box keeps plastic clean and simple to dispense.

Part #

Description

Size

400

Economy Plastic

12’ x 400’

Page 7

Premium Plastic Sheeting: High density plastic sheeting that offers high tear and puncture strength. Specially treated so paint clings to surface and doesn’t flake off. EZ Dispenser keeps plastic clean and simple to dispense, even without a masking machine. PAINTABLE!

Part #

Description

Size

403

Hi Density Plastic

12’ x 400’ 16’ x 350’

403-16

Extra Wide Hi Density Plastic

Masking Tape Professional quality masking tape at an affordable price. Good conformability and staying power without adhesive transfer.

Part #

Description

Size

334 338 340

Professional Masking Tape-Beige 3/4” Professional Masking Tape-Beige 1-1/2”

Professional Masking Tape-Beige

2”

Wheel Maskers: Canvas wheel maskers for overspray protection of automotive tires. #2000 fits up to most 15” tires, #2017 fits larger SUV and Truck tires

Part # 2000 2017

Description

Size

Blue Wheel Maskers Blue Wheel Maskers

Up to 15” Up to 17”

Seat Covers: Plastic seat covers to protect customer’s interior seats. Slip and grip plastic keeps seat cover in place. 125 covers in a box.

Part #

Description

Size

407

Slip & Grip Seat Covers

Fits Most

Floor Mats: White plastic floor mats to protect customer’s interior floors. Slip and grip plastic keeps mats in place. 250 mats on a roll.

Description

Size

Part #

409

Slip & Grip Floor Mats

16”x21”

Page 8

Lightweight Body Filler An economical Lightweight Body Filler offering smooth and creamy tex- ture that spreads easily for excellent feather edging. Adheres to galva- nized, aluminum and bare steel. Sands easily and won’t load up sand paper. Great for a general use body filler.

Part # 4401 4404

Description

Size

Lightweight Body Filler Lightweight Body Filler

Gallon Quart

Substrates & Prep Clean surface removing dirt, wax, grease & oil. Grind away any corrosion or rust using 36 or 40 grit grinding disc. Rough sand substrate no finer than 80 grit paper. Mixing 50 Parts Lightweight Body Filler 1 Part RED OR BLUE Cream Hardener

50:1

As a general rule, scoop appropriate amount of body filler for a single application on a non porous surface. Drawing a straight line across the widest points of body filler “puddle” will provide the 50:1 mix ratio needed for proper catalyzation. Do not whip air into mixture, stir in circular motion. Application Apply thin layer using firm pressure to ensure proper adhesion. Apply additional layers building slightly higher and larger to allow for sanding. Repeat process as necessary. Drying

Gel Time Approximately 4 to 7 minutes Sand Time Approximately 15 minutes Recoat

Allow 1 hour cure time before coating with primer or sealer.

Master Tips Do not return unused catalyzed portion to filler can. Allow for extended flash off time if wax & grease remover used on filler.

Page 9

Premium Lightweight Body Filler Truly a premium body filler that’s tack free, self etching, and stain resist- ant. Formulated with finest resins available to offer superior spreading and sanding properties. Self etching body filler adheres to steel, alu- minum, zinc, and galvanized metals.

Part # 4450

Description

Size

Premium Body Filler

Gallon

Substrates & Prep Clean surface removing dirt, wax, grease & oil. Grind away any corrosion or rust using 36 or 40 grit grinding disc. Rough sand substrate no finer than 80 grit paper. Mixing 50 Parts Body Filler 1 Part BLUE Cream Hardener

50:1

As a general rule, scoop appropriate amount of body filler for a single application on a non porous sur- face. Drawing a straight line across the widest points of body filler “puddle” will provide the 50:1 mix ratio needed for proper catalyzation. Do not whip air into mixture, stir in circular motion. Application Apply thin layer using firm pressure to ensure proper adhesion. Apply additional layers building slightly higher and larger to allow for sanding. Repeat process as necessary. Drying

Gel Time Approximately 4 to 7 minutes Sand Time Approximately 15 minutes Recoat

Allow 1 hour cure time before coating with primer or sealer.

Master Tips Do not return unused catalyzed portion to filler can. Allow for extended flash off time if wax & grease remover used on filler.

Page 10

Fiberglass Reinforced Body Filler High strength body filler that offers superior adhesion to steel, zinc, and galvanized metals. Corrosion resistant, waterproof, and rust proof. Strength comes from short strands of fiberglass fibers. A final coat of glazing or finishing putty is recommended.

Part # 4600

Description

Size

Fiberglass Body Filler

Gallon

Substrates & Prep Clean surface removing dirt, wax, grease & oil. Grind away any corrosion or rust using 36 or 40 grit grinding disc. Rough sand substrate no finer than 80 grit paper. Mixing 50 Parts Body Filler 1 Part BLUE Cream Hardener

50:1

As a general rule, scoop appropriate amount of body filler for a single application on a non porous sur- face. Drawing a straight line across the widest points of body filler “puddle” will provide the 50:1 mix ratio needed for proper catalyzation. Do not whip air into mixture, stir in circular motion. Application Apply thin layer using firm pressure to ensure proper adhesion. Apply additional layers building slightly higher and larger to allow for sanding. Repeat process as necessary. Drying

Gel Time Approximately 4 to 7 minutes Sand Time Approximately 15 minutes Recoat

Allow 1 hour cure time before coating with primer or sealer.

Master Tips Do not return unused catalyzed portion to filler can. Allow for extended flash off time if wax & grease remover used on filler.

Page 11

2K Glazing Putty A two part glazing and finishing putty offering super smooth texture, fast dry, and no shrinkage. Excellent adhesion properties allows you to apply directly to metal, body filler, fiberglass and cured topcoats to fill minor imperfection.

Part # 4724

Description

Size

2K Glazing Putty

24 oz Tube

Substrates & Prep Clean surface removing dirt, wax, grease & oil. Grind away any corrosion or rust using 36 or 40 grit grinding disc. Finish sand with 180 grit before applying putty. Mixing 50 Parts Glazing Putty 1 Part BLUE Cream Hardener

50:1

As a general rule, scoop appropriate amount of body filler for a single application on a non porous sur- face. Drawing a straight line across the widest points of body filler “puddle” will provide the 50:1 mix ratio needed for proper catalyzation. Do not whip air into mixture, stir in circular motion. Application Apply thin layer using firm pressure to ensure proper adhesion. Apply additional layers building slightly higher and larger to allow for sanding. Repeat process as necessary. Drying

Gel Time Approximately 2 to 3 minutes Sand Time Approximately 15 minutes Recoat

Allow 1 hour cure time before coating with primer or sealer.

Master Tips Do not return unused catalyzed portion to filler can. Allow for extended flash off time if wax & grease remover used on filler.

Page 12

Fiberglass Resin Autobody Master Fiberglass Resin offers finishing grade resin unlike many other brands that offer laminating grades. Used in conjunction with fiberglass cloth, mat, and tape. Fiberglass Resin offers excellent rebuilding properties to torn or rotted fiberglass & metal.

Part # 4100 4104

Description

Size

Fiberglass Resin Fiberglass Resin

Gallon Quart

Substrates & Prep Metal, fiberglass, & wood Surface must be clean and dry. Strip any existing paint or varnish. Rough sand or sand blast metal surfaces. Mixing

1 oz to

1 ounce of fiberglass resin 12 drops of liquid hardener Application

Fiberglass and metal - Apply tack coat to substrate. When coat becomes tacky, apply fiberglass fabric, starting at one end and unrolling fabric working out bubbles and wrinkles. Apply catalyzed resin using a brush, roller, squeegee or spreader. Completely saturate fabric and work out any bub- bles or wrinkles. If additional layers are needed, apply fabric before previous layer has cured to avoid sanding between layers. Soft Woods - If resin soaks in, continue to apply layers until a tacky coat can be achieved, then apply cloth or mat. Drying Gel Time 10-15 minutes Sand Time 30 minutes Master Tips Do not apply in direct sunlight. Sunlight can breakdown resin properties during application and cause improper cure and adhesion. In warmer temperatures, 90°F and above, use 50% less harden- er to allow for longer working time. In colder temperatures, 65°F and below, use up to 100% more hardener. Do not apply at temperatures below 60 degrees. Always begin and end project with a wet coat of resin.

Page 13

FIBERGLASS CLOTH & MAT • CLOTH: Interwoven cloth material that offers high patching strength to repairs of fiberglass, metal, and plastic. Must be used with fiberglass, poly- ester, or epoxy resins. Wets fast, lays down smooth and easily drapes to conform to contours and shapes. Excellent high strength backing patch over holes, punctures, and breaks. • MAT: Fiberglass mat material reinforced with long, fiberglass strands. Used to reinforce fiberglass, polyester, and epoxy resins where bulk and water- proofing is required. Use for the repair of holes and badly damaged areas in fiberglass, metals, and plastics. Easy to handle on flat or curved surfaces. May be used with or tape to build layers of laminate Fiberglass Cloth Part # Description Size 4110 Fiberglass Cloth 1yd x 38” 4111 Fiberglass Cloth 3yd x 38” Fiberglass Mat Part # Description Size 4115 Fiberglass Mat 1yd x 38” 4116 Fiberglass Mat 3yd x 38”

Substrates & Prep Surface must be dry, clean, and free from paint, varnish, dirt and other foreign matter. Rough sand or sand blast to ensure proper adhesion. Application

First apply wet coat of catalyzed resin with roller or brush. When resin becomes tacky, apply fiberglass cloth. Working from one end, unroll fabric, stretching and working out air bubbles. Once cloth is applied roll out remaining bubbles with resin roller. Apply second coat of resin with roller or brush Apply second layer of fabric to build up surface. If resin cures between layers, surface must be sanded for proper adhesion between coats. Master Tips Do not apply in direct sunlight. Sunlight can breakdown resin properties during application and cause improper cure and adhesion. Do not apply at temperatures below 60 degrees. Always begin and end project with a wet coat of resin.

Page 14

Lacquer Thinner - General Purpose Grade Formulated from high quality solvents to offer a high solvency general purpose lacquer thinner. Part # Description Sizes 5700- General Purpose Lacquer Thinner 1,5,16 & 55 Lacquer Thinner - Color Grade Special blend of high quality solvents for thinning lacquer color coats or lacquer primer surfac- ers. Part # Description Sizes 5770- Fast Color Grade Lac. Thinner 1,5,16 & 55 5780- Medium Color Grade Lac. Thinner 5790- Slow Color Grade Lac. Thinner Enamel Reducer Excellent for acrylic enamel paints & primers. Compatible with all major paint manufacturers. Part # Description Sizes 5855- Fast Enamel Reducer 1,5, & 55 5875- Medium Enamel Reducer 5890- Slow Enamel Reducer Premium Urethane Reducer Premium urethane grade solvents for reducing urethane, epoxy, primers and clear coats. Part # Description Sizes 8860 Fast Urethane Reducer 1 Gallon 8870 Medium Urethane Reducer Paint Prep Solvent based. Excellent cleaner prior to priming, painting, pin stripping, or attaching graphics and emblems. Removes wax, oil, grease, and other surface contaminates. Part # Description Size 5900- Wax & Grease Remover 1 & 5 Gallon Waterborne Wax & Grease Remover Water based. Removes wax, oil, grease, and other surface contaminates. Also works great as a gun cleaner for water based products. Excellent final cleaner prior to paint application. Part # Description Size 5911 Waterborne Wax & Grease Remover Quart Spray Gun Cleaning Solvent Formulated for fast and efficient cleaning of spray guns. Removes old hard dry finishes and can be used over and over many times. Part # Description Size 5914-1 Spray Gun Cleaning Solvent Gallon 5914-5 Spray Gun Cleaning Solvent 5-Gallon 5914-55 Spray Gun Cleaning Solvent 55-Gallon

Page 15

Mineral Spirits Slow-dry solvent for oil-based paints and alkyd enamels. Also good parts cleaner.

Description Mineral Spirits Mineral Spirits

Part # 5950-1 5950-5

Size

Gallon 5-Gal. 55-Gal.

5950-55 Mineral Spirits

M.E.K. - Methyl Ethyl Ketone Medium dry solvent for lacquers and copolymers. Use only where directed.

Description

Part # 5975-1 5975-5

Size

M.E.K. M.E.K.

Gallon 5-Gal. 55-Gal.

5975-55 M.E.K.

VM&P Naptha Fast-dry solvent for oil-based paints & alkyd enamels. Use when spraying. Part # Description Sizes 5960-1 VM&P Naptha Gallon 5960-4 VM&P Naptha Quart Xylene For thinning synthetic enamels, epoxy paint, rubber- based paint and varnishes. Part # Description Sizes 5980-1 Xylene Gallon 5980-5 Xylene 5-Gal. 5980-55 Xylene 55-Gal. Toluene Fast evaporating solvent for cleaning and a reducer for certain primers, topcoats, oils and resins. Part # Description Size 5970-1 Toluene Gallon 5970-5 Toluene 5-Gal. 5970-55 Toluene 55-Gal. Acetone Great panel cleaner and a solvent for epoxies, vinyl, lacquer, contact cements and adhesives. Part # Description Size 5990-1 Acetone Gallon 5990-5 Acetone 5-Gal. 5990-55 Acetone 55-Gal.

Page 16

Basecoat Reducer Specialized formulation of reducers to be used as an excellent alternative basecoat reducers for DuPont’s Chromabase basecoats. Part # Description Size 5530 Basecoat Reducer D - Fast Gallon 5531 Basecoat Reducer D - Medium Gallon

Mixing - SHAKE WELL BEFORE USE! Basecoat Reducer: 1 Part DuPont Chromabase, 1 Part Basecoat Reducer

Drying Flash Recoat

5-10 Min. 15-30 Min.

Clear Window If Basecoat dries more than 24 hours, scuff sand and reapply color. Master Tips SHAKE WELL BEFORE USE! Do not use Basecoat Reducer to clean equipment or melt in overspray. Basecoat reducer should be tightly sealed during storage. VOC RTS D<6.4

Page 17

Paint Prep Solvent based. Excellent cleaner prior to priming, painting, pin stripping, or attaching graphics and emblems. Removes wax, oil, grease, and other surface contaminates.

Part # 5900-1 5900-5

Description

Size

Wax & Grease Remover Wax & Grease Remover

Gallon 5 Gallon

Generously apply wax and grease remover to substrate either with a cloth or by spray applicator. Wipe surface with a clean dry cloth before the wax and grease remover has flashed off the substrate.

Anti Static Wax & Grease Remover

Water based. Use on plastics to avoid flash fire from static spark. Removes static from pre-paint surface thus reducing dirt, dust and lint. Excellent final cleaner and wipe down solution prior to priming, painting or pin stripping. Removes wax, oil, grease, and other surface contaminates. Also works great as a gun cleaner for water based products.

Part # 5911

Description

Size

Wax & Grease Remover

Quart

Generously apply wax and grease remover to substrate with either a cloth or by spray applicator. Wipe surface with a clean wet cloth before the wax and grease remover has flashed off the substrate. Finish drying surface with clean dry cloth. Try to avoid excessive wiping.

Master Tip

Use Anti Static Wax & Grease Remover when degreasing on or around body fillers or putties. Because fillers and putties can “hold” solvents when wiped with solvent based degreasers, a “ring” can appear if all of the solvent had not released prior to topcoating. Anti Static is waterbased and will not cause the “ring” caused by trapped solvent when using a solvent based degreaser around fillers or putties. General Purpose Adhesive Remover Removes adhesives, silicone, wax, grease, oil, tar, rubber cement and other contami- nants from a variety of surfaces. Leaves no oily film and dries fast. Nozzle top included for easy dispensing.

Part # 5984

Description

Size

General Purpose Adhesive Remover Quart

Page 18

Wet Look Acrylic Enamel Hardener High solids catalyst to enhance the gloss and durability of acrylic enamel. Wet Look offers a super high gloss finish that’s more durable and chemical resistant than conventional enamel finishes. Part # Description Size 8105 Acrylic Enamel Hardener 1/4 Pint 8108 Acrylic Enamel Hardener Pint

Substrates & Prep Surface must be primed and or sealed and ready for paint. Always clean surface with wax & grease remover prior to painting. Mixing

Typically 8:4:1 (8 Parts Acrylic Enamel Color : 4 Part Enamel Reducer : 1 Part Wet Look Hardener) Note: Follow paint manufacturers reduction ratio. Some paints come partially reduced from manufacturer. Drying Flash Time: 10-15 minutes Dust Free: 10 minutes Tack Free: 1 hour Sand/Recoat: Overnight to 48 hours Pot Life: Typically 4 - 6 hours Master Tips Due to large variance in reducer temperature ranges, above figures are typical of performance when proper temperature reducer is used. Always add catalyst slowly to reduced paint. Adding catalyst to quickly or to unreduced paint can cause the paint to shock.

Synthetic Enamel Hardener High solids catalyst to enhance synthetic enamel gloss and durability. Produces a finish that’s more durable and chemical resistant than conventional synthetic enamel finishes. Part # Description Size 8132 Synthetic Hardener Pint

Substrates & Prep Surface must be primed and or sealed and ready for paint. Always clean surface with wax & grease remover prior to painting. Mixing

Typically 8:4:1 (8 Parts Synthetic Enamel Color : 4 Part Synthetic Reducer : 1 Synthetic Hardener) Note: Follow paint manufacturers reduction ratio. Some paints come partially reduced from manufacturer. Drying Flash Time: 10-15 minutes Dust Free: 10 minutes Tack Free: 1 hour Sand/Recoat: Overnight to 48 hours Pot Life: Typically 4 - 6 hours Master Tips Due to large variance in reducer temperature ranges, above figures are typical of performance when prop- er temperature reducer is used. Always add catalyst slowly to reduced paint. Adding catalyst to quickly or to unreduced paint can cause the paint to shock.

Page 19

PRIMERS

Super Etch Super Etch is a precoat primer that offers the ultimate in adhesion to bare steel, aluminum, galvanized and zinc coated substrates. Formulated to be used as a pretreatment coating, Super Etch bites into the substrate and promotes the adhesion of additional primers and sealers. Color: Transparent Olive Green. Mix Ratio 1:1 Etch Fill Etch Fill provides the convenience of a self etching corrosion resistant precoat primer with moderate filling properties. Etch Fill offers excellent adhesion to bare steel, aluminum, gal- vanized and zinc coated substrates. Etch Fill etches into the substrate and fills minor imperfections. Etch Fill can be topcoated with additional primers, sealers or topcoat direct- ly with color. Color: Mauve/Rose. Mix Ratio 1:1 Epoxy Primer Epoxy Primer offers good corrosion resistance, excellent adhesion, and excellent color holdout. Epoxy Primer can also be used as a sealer when reduced with a urethane grade reducer. Lead, chromate and isocyanate free. Color: Green/Gray, Black and White. Mix Ratio 4:1 Fast Prime Fast Prime is an extremely versatile, high build primer surfacer that’s ready to sand in 45 minutes. Fast Prime offers excellent corrosion resistance and adhesion to bare metal. Use Fast Prime as the primer of choice when you’re looking for a production oriented primer surfacer. Color: Gray. Mix Ratio 4:1 Urethane Primer Urethane Primer is formulated to offer a premium quality, acrylic urethane coating with excellent filling and building properties. Urethane Primer is the ideal primer for urethane base/clear topcoats with excellent color holdout. Flexible, fast dry, no shrinkage, and very resistant to sand scratch swelling. Color: Buff or Gray. Mix Ratio 4:1. Hi Prime Hi Prime is an acrylic lacquer primer surfacer offering high solids, quick filling, quick build, easy sanding and excellent adhesion to pre-coated substrates. Excellent everyday primer with minimal film shrinkage. Color Red Oxide, Gray and Hot Rod Black. Mix Ratio 2:3. Acrylic Sealer Ready to spray acrylic sealer for faster topcoat coverage and better color holdout. This sealer is fast drying, easy flowing and provides a uniform color that’s satin smooth. Gray. ShadeSystem 2K Sealer ShadeSystem 2K Sealer is a super productive primer sealer that offers a variable gray shade intermix system, excellent flow and leveling, excellent color holdout and medium build to fill many small surface imperfections. ShadeSystem 2K Sealer can be topcoated 15-30 minutes after application, nib sanded after 20-30 minutes if needed.

Page 20

Super Etch Super Etch is designed to be used as a pre-treatment coating that etches into the repair substrate and offers a base that promotes the adhesion of additional primers or sealers. Applied to properly prepared steel, aluminum, galvanized & zinc coatings, Super Etch will provide outstanding corrosion resistance and promote adhesion. Pre-treating with Super Etch is especially beneficial when using waterborne primers over aluminum and steel substrates. Product color: Transparent Olive Green

Part # 8462 8162

Description

Size

Super Etch Primer Super Etch Catalyst

Quart Quart

Substrates • Steel, Galvanized & Aluminum - Sand with 80 - 180 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover. Mixing • 1 Part Super Etch Pre-Treatment Coating • 1 Part Super Etch Catalyst • Induction Period - 5 minutes stirred Set Up Tech Info Tip/Needle: 1.3mm to 1.5mm Spot Air Pressure: 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap Viscosity (#2 Zahn) 16 - 18 seconds Film Build: 0.3 - 0.4 mils DFT Coverage: 83 sq. ft. @ 1 mil Application Apply 1 medium wet coat to provide excellent adhesion promotion and corrosion resistance. Product is not designed to fill sand scratches or minor imperfections. Drying Sand Time Sanding is not recommended Recoat 30 minutes cure time before recoating with additional primers or sealers. Recoat within 4 hours, beyond 4 hours, lightly scuff and reapply 1 coat of Super Etch. Pot Life 24 hours - product should be stored in plastic container Physical Data Volume Solids RTS: 5.2% VOC RTS: 6.2 lb./gallon Humidity Resistance: Excellent Salt Spray Test: Excellent Master Tips Primer or sealer must be applied before color coat. Do not directly top coat with color. Application should be a single wet coat, do not use as a filling primer. If not recoated with primer or sealer within 4 hours, lightly scuff and reapply 1 coat of Super Etch before applying additional primers or sealers. Do not apply over lacquer products.

Page 21

Etch Fill Etch Fill provides the convenience of a self etching corrosion resistant precoat primer with moderate filling properties. Etch Fill offers excellent adhesion to bare steel, aluminum, galvanized, & zinc coated substrates. Etch Fill etches into the substrate and fills minor imperfections. Etch Fill can be topcoated with additional primers, sealers or topcoat directly with color. Product color: Mauve/Rose

Part # 8466 8467 8166 8167

Description

Size

Etch Fill Primer Etch Fill Primer Etch Fill Catalyst Etch Fill Catalyst

Gallon Quart Gallon Quart

Substrates • Fully cured finishes - Sand with 240 - 320 grit paper • Steel, Galvanized & Aluminum - Sand with 80 - 180 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover. Mixing

1 Part Etch Fill Primer 1 Part Etch Fill Catalyst Set Up Tech Info Tip/Needle: Spot Air Pressure:

1.3mm to 1.5mm

Conventional 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: Conventional 45 - 55 psi / HVLP 5 to 10 psi at cap Viscosity (#2 Zahn) 18-20 seconds Film Build: 2-3 mils DFT Coverage: 205 sq. ft. @ 1 mil Application Apply 1 to 2 full wet coats to provide excellent adhesion, corrosion resistance, and fill minor imperfections. Allow 5 to 10 minutes between coats. Drying Sand Time Sanding not recommended Recoat 30 minutes cure time before recoating with primer or sealer, recoat within 24 hours Topcoat 1-2 hours minimum, sealing is recommended. See Master Tips. Pot Life 24 hours - Product should be stored in plastic container Physical Data Volume Solids RTS: 12.8% VOC RTS: 5.3 lb./gallon Humidity Resistance: Excellent Salt Spray Test: Excellent Master Tips Heavier coats should be allowed additional cure time before the application of additional primers, sealers or topcoats. As a general rule, allow 1 hour per wet coat before topcoating direct with color. Sealing is recommended because if not fully cured, Etch Fill can “yellow” topcoat color. If allowed to cure longer than 24 hours, scuff sand before recoating or topcoating. Do not tint.

Page 22

Epoxy Primer An outstanding quality, two component, isocyanate, lead, and chromate free epoxy primer and sealer with good corrosion resistance. Offers excellent adhesion to prepared metal, fiberglass and aluminum surfaces.

Description

Size

Part # 8411 8412 8413 8414 8416 8121 8122

Epoxy Primer Green/Gray Epoxy Primer Green/Gray Epoxy Primer Black Epoxy Primer Black Epoxy Primer White

Gallon Quart Gallon Quart Quart Quart

Epoxy Catalyst Epoxy Catalyst

Half Pint

Substrates • Fully Cured Finishes - Sand with 240-320 grit paper • Steel, Galvanized& Aluminum - Sand with 80-180 grit paper • Fiberglass and SMC - Sand with 150-240 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover. Mixing VOC Compliant Primer Conventional Primer Conventional Sealer 4 parts Epoxy Primer 4 Primer 4 Primer 1 part Epoxy Catalyst 1 Catalyst 1 Catalyst Up to 1/2 Part Urethane Reducer 3 Urethane Reducer 4 Urethane Reducer 5 Min. Mechanical Induction 5 Min. Mechanical Induction 5 Min. Mechanical Induction Set Up Tech Info Tip/Needle: 1.5mm to 1.8mm Spot Air Pressure 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap VOC Primer Conv. Primer Conv. Sealer Viscosity (#2 Zahn) 20-25 Sec 19-22 Sec 16-18 Sec Film Build 1.0-1.2 mils DTF .8-1.0 mils DTF .5 mils DTF Coverage (@ 1mil) 481 Sq. Ft. 336 Sq. Ft. 288 Sq. Ft. Application VOC Compliant Primer Conventional Primer Conventional Sealer 1 full wet coat 1-2 full wet coats 1 wet coat w/10-15 min. flash Drying VOC Primer Conv. Primer Conv. Sealer Sand Time Not recommended 60 minutes Not recommended Recoat 60 minutes 60 minutes 30 minutes Topcoat 60 minutes 60 minutes 30 minutes Pot Life 8 hours 8 hours 8 hours

Physical Data Volume Solids RTS Humidity Resistance Salt Spray Resistance VOC RTS

30%

21%

18%

4.8 lb/gal. Excellent Excellent

5.5 lb/gal. Excellent Excellent

5.7 lb/gal. Excellent Excellent

Master Tips Do not use over lacquer products. Recoat within 72 hours. Greater than 72 hours, scuff sand before top coat. In temperatures over 77°F recoat within 36 hours.

Page 23

Fast Prime Fast Prime is an extremely versatile, high build primer surfacer that’s ready to sand in 45 minutes. Fast Prime offers excellent corrosion resistance and adhesion to bare metal. Use Fast Prime as the primer of choice when you’re looking for a production oriented primer surfacer. Color: GRAY

Part # 8474 8475 8174 8175

Description

Size

Fast Prime Primer Surfacer Fast Prime Primer Surfacer

Gallon Quart Quart 1/2 Pint

Fast Prime Activator Fast Prime Activator

Substrates • Fully cured finishes - Sand with 240 - 320 grit paper • Steel, Galvanized & Aluminum - Sand with 120-220 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover. Mixing 4 Parts FAST PRIME Primer Surfacer 1 Part FAST PRIME Activator Set Up Tech Info Tip/Needle: 1.3mm to 1.5mm Spot Air Pressure: Conventional 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: Conventional 45 - 55 psi / HVLP 5 to 10 psi at cap Viscosity (#2 Zahn) 23-24 seconds Film Build: 1.3-1.5 mils per full wet coat Coverage: 545 sq. ft. @ 1 mil Application Apply 2 to 3 full wet coats to provide excellent adhesion, corrosion resistance, and fill imperfections. Allow 5 to 10 minutes between coats. Drying Sand Time 45 minutes. Final block with 600 grit or finer. Recoat 45 minutes cure time before recoating with primer or sealer. Topcoat 45 minutes cure time before topcoating with color. Pot Life 2-4 hours

Physical Data Weight Solids RTS:

53.3%

VOC RTS:

4.8 lb./gallon

Humidity Resistance: Excellent Salt Spray Test: Excellent Master Tips

Heavier coats should be allowed additional cure time before sanding or the application of additional primers, sealers or topcoats. In high heat conditions (above 85°F), it is recommended that you drop your air pressure to 20-25 lbs to help slow the curing process. Large panels of bare metal should be precoated with a self etching primer for maximum adhesion and corrosion protection. Do not acceler- ate or add fish eye eliminator.

Page 24

Urethane Primer Surfacer A premium acrylic urethane primer surfacer designed as a high build easy sanding primer surfacer that resists sand scratch swelling and shrinkage. 2K Urethane Primer has excellent adhesion and flex proper- ties. The resins utilized in this formula offer excellent color holdout and are ideal for urethane top coats and base coat clear coat systems. Part # Description Size 8441 Urethane Primer- Buff Gallon 8442 Urethane Primer- Buff Quart 8443 Urethane Primer- Gray Gallon 8444 Urethane Primer- Gray Quart 8141 Urethane Primer Standard Catalyst Quart 8142 Urethane Primer Standard Catalyst 1/2 Pint 8143 Urethane Primer FAST Catalyst Quart

Substrates • Fully cured finishes - Sand with 240 - 320 grit paper • Steel, Galvanized & Aluminum - Sand with 80 - 180 grit paper • Fiberglass & SMC - Sand with 150 - 240 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover. Mixing Full Body Primer Medium Build Primer Sealer 4 parts Urethane Primer 4 Primer 4 Primer 1 part Urethane Catalyst 1 Catalyst 1 Catalyst 1/2 Urethane Reducer 2 Urethane Reducer Set up Tech Info Tip/Needle: 1.5mm to 1.8mm Spot Air Pressure: 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap HIgh Build Sealer Viscosity (#2 Zahn) 20-25 sec. 16-18 sec. Film Build: 2.5 - 4.5 mils 0.8 -1.2 mils Coverage: 555 @ 1 mil 308 @ 1 mil Application Apply 2 to 3 medium wet coats to fill sand scratches, minor imperfections, and build low areas. Allow 10-15 minutes between coats. As a sealer apply 1 full wet coat. Drying Sand Standard Catalyst 2-4 hours Fast Catalyst 1 -2 hours Recoat Cure 3 hours before recoating with additional primers, sealers or color topcoat. Recoat within 12 hours. Pot Life 3 - 4 hours

Physical Data Volume Solids RTS

34.6% @ 4:1 19.21% @ 4:1:2 4.8 lb./g as primer 5.8 lb./g as sealer

VOC RTS:

Humidity Resistance: Salt Spray Test: Lead & Chromate Levels

Excellent Excellent

Lead & Chromate Free

Master Tips If shop or substrate temperature is below 60°F, urethane accelerator recommended. Curing process of isocyanate products are severely inhibited below 60°F. Primer should be recoated or topcoated within 12 hours. If not topcoated within 12 hours, sand with 500 grit paper before recoating with primer, sealer, or color topcoat. Retarders - Recommended only in severe heat and humidity. Flex Agent - Recommended when repairing flexible substrates OFF the vehicle.

Page 25

Hi Prime Hi Prime is a high solids acrylic lacquer primer surfacer formulated for quick filling, easy sanding, and excellent adhesion on pre-coated substrates. Its quick filling properties easily fills up to 80 grit sand scratches . An economical and production shop oriented primer that provides an excellent base and promotes topcoat adhesion. VOC complaint when used with color grade lacquer thinner.

Part # 8400 8401 8402 8403 8404

Description

Size

Hi Prime - Gray Hi Prime - Gray

Gallon Quart Gallon Quart Gallon

Hi Prime - Red Oxide Hi Prime - Red Oxide Hi Prime - Hot Rod Black

Substrates • Fully cured finishes - Sand with 240 - 320 grit paper • Steel, Galvanized & Aluminum - Sand with 80 - 180 grit paper & precoat with Super Etch Primer. • Fiberglass & SMC - Sand with 150 - 240 grit paper • Always clean surface prior to application with 5900 or 5911 wax & grease remover Mixing

2 Parts Hi Prime Primer Surfacer 3 Parts VOC Compliant Thinner Set Up Tech Info Tip/Needle:

11/2 2 3

1.5mm to 1.8mm

Spot Air Pressure: Overall Air Pressure: Viscosity (#2 Zahn)

35 - 45 psi / HVLP 5 to 10 psi at cap 45 - 55 psi / HVLP 5 to 10 psi at cap

18 - 20 seconds

Film Build Coverage

0.6-0.8 mils DFT per full wet coat

208 sq. ft. @ 1 mil

Application Apply 2-3 full wet coats to provide filling and leveling of sand scratches and minor imperfections on refinish surface. Allow 10 to 15 minutes between full wet coats. Time may vary due to heat and humidity conditions. Adjust accordingly with the appropriate temperature color grade lacquer thinner. Drying Sand Time 20 - 30 minutes with appropriate Lacquer Thinner Recoat 30 minutes dry time, sand with 400 grit before recoating with primer or sealer. Topcoat 30 minutes dry time, sand with 400 grit before topcoating with lacquer or enamel.

Physical Data Volume Solids RTS VOC (sprayable) Humidity Resistance Salt Spray Test Pot Life Lead & Chromate

13%

Indefinite 4.8lbs/gal.

Good Good

Lead & Chromate Free

Master Tips If applying to bare metal, it’s highly recommended to apply Super-Etch Primer first. It is important to choose the proper temperature range lacquer thinner. Accelerated evaporation can actually condense water vapor within primer surfacer and severely reduce primers adhesion and sanding properties. Sealing is recommended if topcoating with a urethane or synthetic enamel topcoat. Allow an extended flash off time after the use of wax & grease removers due to primers porous nature.

Page 26

Acrylic Sealer Ready to spray acrylic sealer for faster topcoat coverage and better color holdout. This sealer is fast drying, easy flowing and provides a uniform color that’s satin smooth. Gray

Part # 8430 8431

Description Acrylic Sealer Acrylic Sealer

Size

Gallon Quart

Substrates Fully Cured Finishes: Sand with 240-320 grit paper Steel, Galvanized & Aluminum: Pre Coat with Super Etch or Etch Fill Self Etching Primer Fiberglass & SMC: Sand with 150-240 grit paper Mixing Ready To Spray Set Up Tech Info Tip/Needle: 1.3mm to 1.5mm Spot Air Pressure: 35 - 45 psi / HVLP 5 to 10 psi at cap Overall Air Pressure: 45 - 55 psi / HVLP 5 to 10 psi at cap Viscosity: #2 Zahn 19-20 seconds Film Build: .05 mils / full wet coat Coverage (@ 1 mil) 387 sq. ft. @ 1 mil Application Apply 1-2 medium coats @ 40-50 psi allowing 10-15 minutes between coats.

Drying Topcoat Recoat

20-30 minutes 30 minutes

Sand Time 30 minutes Pot Life Indefinite - Stir thoroughly

Physical Data Volume Solids RTS

24.1%

Pot Life: VOC RTS:

Indefinite

4.6 lbs/gallon

Master Tips Acrylic Sealer must be mixed well before use. If sealer is allowed to dry for more than 48 hours, scuff sand and reapply 1 coat of sealer before topcoating. Film build, temperature, and humidity will affect dry times.

Page 27

ShadeSystem 2K Sealer ShadeSystem 2K Sealer is a super productive primer sealer that offers a variable gray shade intermix system, excellent flow and leveling, excellent color holdout and medium build to fill many small surface imperfections. Sealer can be topcoated 15-30 minutes after application, nib sanded after 20-30 minutes if needed.

Part # Description

Size

8321 8322 8324 8325 8327 8328 8124 8125 8126 8127

S1 ShadeSystem 2K Sealer White S1 ShadeSystem 2K Sealer White S4 ShadeSystem 2K Sealer Gray S4 ShadeSystem 2K Sealer Gray S7 ShadeSystem 2K Sealer Black S7 ShadeSystem 2K Sealer Black ShadeSystem Sealer Activator ShadeSystem Sealer Activator Slow ShadeSystem Sealer Activator

Gallon Quart Gallon Quart Gallon Quart Quart 1/2 Pint

Quart

Slow ShadeSystem Sealer Activator 1/2 Pint Substrates Fully Cured Finishes: Finish sand with 400-600 grit paper. Steel, Galvanized & Aluminum: Pre Coat with Super Etch or Etch Fill Self Etching Primer Fiberglass & SMC: Finish sand with 400-600 grit paper Mixing 4 Parts Sealer 1 Part Activator S1 S2 S3 S4 S5 S6

S7

Recommended Shade:

No Mix No Mix 8321/8322 1 part S4 2 parts S4 8324/8325 1 part S7 2 parts S7 8327/8328 Whites Lt Red Med Red Med Dk Red Dk Red Dk Red Black Lt Yellow Lt Green Med Green Med Dk Green Dk Green Dk Green Very Dk Red Silvers Lt Blue Med Blue Med Dk Blue Dk Blue Dk Blue Very Dk Green Lt Brown Med Brown Med Dk Brown Dk Brown Dk Brown Very Dk Blue Med Yellow Med Dk Silver Charcoal Silver Dk Charcoal Silver Very Dk Brown 2 parts S1 1 part S1 No Mix 2 part S4 1 part S4

Color Type:

Set Up Tech Info Tip/Needle: Spot Air Pressure: Overall Air Pressure:

1.3mm to 1.5mm

35 - 45 psi / HVLP 5 to 10 psi at cap 45 - 55 psi / HVLP 5 to 10 psi at cap

Film Build:

1-1.5 mils / full wet coat

Coverage (@ 1 mil)

548 sq. ft. @ 1 mil

Application Apply 1 medium wet coat using 35-45 psi at the gun. Allow 15-30 min. flash before topcoating.

Drying Topcoat Recoat

15-30 minutes 30 minutes 20-30 minutes

Sand Time

Physical Data Volume Solids RTS

34.1% 2 hours

Pot Life: VOC RTS:

4.6 lbs/gallon

Master Tips Film build, temperature, and humidity will affect dry times. Do not use accelerator or fish eye eliminator in this product. Make sure you’re ready to apply topcoat before using this sealer. If not topcoated within 40 minutes, you must scuff and re-apply before topcoating.

Page 28

Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16 Page 17 Page 18 Page 19 Page 20 Page 21 Page 22 Page 23 Page 24 Page 25 Page 26 Page 27 Page 28 Page 29 Page 30 Page 31 Page 32 Page 33 Page 34 Page 35 Page 36 Page 37 Page 38 Page 39 Page 40 Page 41 Page 42 Page 43 Page 44

Made with FlippingBook flipbook maker