Table 16. AFBMA and American National Standard Shaft Diameter and Housing Bore Tolerance Limits ANSI/ABMA 7-1995 (R2001) Allowable Deviations of Shaft Diameter from Basic Bore Diameter, Inch Inches mm
Over
Incl.
Over
Incl.
Base Bore Diameter 0.2362 0.3937 6 0.3937 0.7087 10 0.7087 1.1811 18 1.1811 1.9685 30 1.9685 3.1496 50
g6
h6
h5
j5
j6
k5
k6
m5
m6
n6
p6
r6
r7
+.0002 − .0001 +.0002 − .0001 +.0002 − .0002 +.0002 − .0002 +.0002 − .0003 +.0002 − .0004 − .0004 +.0005 − .0004 +.0006 − .0005 +.0007 − .0005 +.0009 − .0006 +.0010 − .0006 +.0012 J7
+.0003 − .0001 +.0003 − .0001 +.0004 − .0002 +.0004 − .0002 +.0005 − .0003 +.0005 − .0004 − .0002 +.0003 − .0002 +.0004 − .0002 +.0005 − .0002 +.0006 − .0003 +.0007 − .0003 +.0009 J6
+.0003 0 +.0004 0
+.0005 +.0002 +.0006 +.0003 +.0007 +.0003 +.0008 +.0004 +.0009 +.0004 +.0011 +.0005 − .0007 +.0002 − .0008 − .0002 − .0009 − .0002 − .0011 − .0002 − .0013 − .0003 − .0015 − .0003 M6
0 − .0004 0 − .0004 0 − .0005 0 − .0006 0 − .0007 0 − .0009 0 +.0008 0 +.0010 0 +.0012 0 +.0014 0 +.0016 0 +.0018 H7
0 − .0002 0 − .0003
− .0002 − .0006 − .0002 − .0007 − .0003 − .0008 − .0004 − .0010 − .0004 − .0011 − .0005 − .0013
10 18 30 50 80
+.0004 +.0001 +.0005 +.0001 +.0006 +.0001 +.0007 +.0001 − .0004 +.0001 − .0005 +.0001 − .0006 +.0002 − .0007 +.0002 K6 − .0008 +.0002 − .0009 +.0002
+.0007 +.0001 +.0008 +.0001 +.0010 +.0001 − .0006 +.0002 − .0007 +.0003 − .0008 +.0004 − .0010 +.0004 K7 − .0011 +.0005 − .0013 +.0005
+.0010 +.0004 +.0012 +.0004 +.0014 +.0005 − .0008 0 − .0010 0 − .0012 0 − .0014 0 M7 − .0016 0 − .0018 0
+.0018 +.0009 +.0019 +.0010
+.0023 +.0015
3.1496 4.7244 80 120
Allowable Deviations of Housing Bore from Basic Outside Diameter of Shaft, Inch
Basic Outside Diameter
G7
H6
N6
N7
P6
P7
0 +.0005 0 +.0006 0 +.0007 0 +.0009 0 +.0010 0 +.0011
− .0009 − .0004 − .0011 − .0005 − .0013 − .0006 − .0015 − .0006 − .0018 − .0008 − .0020 − .0009
− .0011 − .0003 − .0013 − .0003 − .0015 − .0004 − .0018 − .0004 − .0020 − .0005 − .0024 − .0006
− .0012 − .0007 − .0015 − .0008 − .0018 − .0010 − .0020 − .0012 − .0024 − .0014 − .0028 − .0016
− .0014 − .0006 − .0017 − .0007 − .0020 − .0008 − .0023 − .0009 − .0027 − .0011
0.7087 1.1811 18 1.1811 1.9685 30 1.9685 3.1496 50
30 +.0003 +.0011 50 +.0004 +.0013 80 +.0004 +.0016
3.1496 4.7244 80 120 +.0005 +.0019 4.7244 7.0866 120 180 +.0006 +.0021
7.0866 9.8425 180 250 +.0006 +.0024 − .0031 − .0013 Based on ANSI/ASME B4.1-1967 (2009; out of print) Preferred Limits and Fits for Cylindrical Parts. Symbols g6, h6, etc., are shaft and G7, H7, etc., hole limits designations. For larger diameters and metric values see AFBMA Standard 7.
Made with FlippingBook - Share PDF online